Search results for "Invention"
showing 10 items of 13027 documents
Electron transport and the effect of current annealing in a two-point contacted hBN/graphene/hBN heterostructure device
2020
In this work, we fabricated a 2D van der Waals heterostructure device in an inert nitrogen atmosphere by means of a dry transfer technique in order to obtain a clean and largely impurity free stack of hexagonal boron nitride (hBN)-encapsulated few-layer graphene. The heterostructure was contacted from the top with gold leads on two sides, and the device’s properties including intrinsic charge carrier density, mobility, and contact resistance were studied as a function of temperature from 4 K to 270 K. We show that the contact resistance of the device mainly originates from the metal/graphene interface, which contributes a significant part to the total resistance. We demonstrate that current…
A fully-digital realtime SoC FPGA based phase noise analyzer with cross-correlation
2017
We report on a fully-digital and realtime operation of a phase noise analyzer using modern digital techniques with cross-correlation. With the advent of system on chip field-programmable gate arrays (SoC FPGAs) embedding hard core central processing unit, coprocessor and FPGA onto a single integrated circuit, the building of sensitive analysis devices for Time & Frequency research is made accessible at virtually no cost and benefits from reconfigurability. Used with high-speed digitizers we have successfully implemented a four-channel system whose preliminary results at 10 MHz shows a residual white noise floor < −185 dBrad2/Hz up to 5 MHz off the carrier, and flicker < −127 dBrad2/Hz using…
Identification of induction motor thermal model for improved drivetrain design
2016
Selection of components of electric drivetrains is not only based on evaluating their ability to perform according to mechanical specifications, but — what is equally important — on assessing their thermal protection limits. These are typically affected by electrical and thermal properties of motors and drives. Although rated parameters (such as power, torque, speed, etc.) are easily accessible in catalogs of equipment producers, more specific properties like mass / length of copper winding, heat dissipation factor, rotor / stator dimensions etc. are not available to customers. Therefore, effective selection of drivetrain components is limited due to the lack of sufficient data and the need…
Sensorless control of induction motors using an extended Kalman filter and linear quadratic tracking
2017
Induction motors are the most commonly used prime-movers in industrial applications. Many induction motors supplied by frequency converters are coupled with a physical angular rotor position/velocity sensor which makes the drive complex and require maintenance. This paper presents a sensorless control structure to avoid using a physical angular rotor position/velocity sensor. The proposed method estimates and control the angular rotor velocity using optimal control theory. The optimal controller used in this paper is based on linear quadratic tracking and the states of the machine are estimated using an extended Kalman filter. Both the controller and the estimator utilize the same internal …
Strategies for numerical simulation of linear friction welding of metals: a review
2017
Linear friction welding (LFW) is a solid-state joining process used to weld non-axisymmetric components. Material joining is obtained through the reciprocating motion of two specimens undergoing an axial force. During this process, the heat source is determined by the frictional work transformed into heat. This results in a local softening of the material and plays a key role in the onset of the bonding conditions. In this paper, a critical analysis of the different approaches used to simulate the LFW processes is provided. The focus of the paper is the comparison of different modeling strategies and the most relevant outputs available, i.e. temperature, strain and stress distribution, mate…
Resistive communications based on neuristors
2017
Memristors are passive elements that allow us to store information using a single element per bit. However, this is not the only utility of the memristor. Considering the physical chemical structure of the element used, the memristor can function at the same time as memory and as a communication unit. This paper presents a new approach to the use of the memristor and develops the concept of resistive communication.
High-frequency electrodeless lamps in argon–mercury mixtures
2005
In this paper, numerical and experimental investigations of high-frequency (HF) electrodeless lamps in argon–mercury mixtures are performed. The intensities of the mercury spectral lines having wavelengths λ = 404.66, 435.83, 546.07 nm (7 3S1–6 3P0,1,2) and the resonance line λ = 253.7 nm (6 3 P1–6 1S0) are measured at a wide range of mercury pressures, varying the HF generator current and argon filling pressure. A stationary self-consistent model of HF electrodeless discharge lamp is developed including kinetics of the excited mercury and argon atomic states. Based on the developed model, the radiation characteristics of the discharge plasma are calculated. Numerical simulation of the line…
Recent improvements on micro-thermocouple based SThM
2017
The scanning thermal microscope (SThM) has become a versatile tool for local surface temperature mapping or measuring thermal properties of solid materials. In this article, we present recent improvements in a SThM system, based on a micro-wire thermocouple probe associated with a quartz tuning fork for contact strength detection. Some results obtained on an electrothermal micro-hotplate device, operated in active and passive modes, allow demonstrating its performance as a coupled force detection and thermal measurement system.
Ionization efficiency studies with charge breeder and conventional electron cyclotron resonance ion source
2013
Radioactive Ion Beams play an increasingly important role in several European research facility programs such as SPES, SPIRAL1 Upgrade, and SPIRAL2, but even more for those such as EURISOL. Although remarkable advances of ECRIS charge breeders (CBs) have been achieved, further studies are needed to gain insight on the physics of the charge breeding process. The fundamental plasma processes of charge breeders are studied in the frame of the European collaboration project, EMILIE, for optimizing the charge breeding. Important information on the charge breeding can be obtained by conducting similar experiments using the gas mixing and 2-frequency heating techniques with a conventional JYFL 14 …
Object size effect on the contact potential difference measured by scanning Kelvin probe method
2010
International audience; Contact potential difference (CPD) was measured by macroscopic Kelvin probe instrument and scanning Kelvin probe microscope on Al, Ni and Pt on ITO substrates at ambient conditions. CPD values measured by scanning Kelvin probe microscope and macroscopic Kelvin probe are close within the error of about 10-30% for large studied objects, whereas scanning Kelvin probe microscope signal decreases, when the object size becomes smaller than 1.4 m. CPD and electric field signals measured using many-pass technique allowed us to estimate the influence of electrostatic field disturbance, especially, in the case of small objects.