Search results for "MS"
showing 10 items of 39361 documents
Parameter sensitivity of flux-linkage based sensorless control for permanent magnet synchronous motors
2017
Sensorless control can be utilized to reduce cost, size and total complexity of a motor drive or enhance reliability of the system. This paper first presents a sensorless control algorithm for a surface permanent-magnet synchronous motor (SPMSM) based on estimated flux linkages and stator currents. Within the algorithm, rotor position error can be predicted by comparing the estimated currents with measured stator currents. Performance of the sensorless control based on flux-linkages and the dependency of the algorithm on motor parameters is then numerically investigated via simulations. It is found from the investigation that the accuracy of the method depends on the motor working condition…
A Novel Fault-Tolerant Routing Algorithm for Mesh-of-Tree Based Network-on-Chips
2019
Use of bus architecture based communication with increasing processing elements in System-on-Chip (SoC) leads to severe degradation of performance and speed of the system. This bottleneck is overcome with the introduction of Network-on-Chips (NoCs). NoCs assist in communication between cores on a single chip using router based packet switching technique. Due to miniaturization, NoCs like every Integrated circuit is prone to different kinds of faults which can be transient, intermittent or permanent. A fault in any one component of such a crucial network can degrade performance leaving other components non-usable. This paper presents a novel Fault-Tolerant routing Algorithm for Mesh-of-Tree …
Determination of elastoplastic properties of TiO2 thin films deposited on dual phase stainless steel using nanoindentation tests
2010
International audience; In recent years, the extraction of mechanical behaviour of thin films by nanoindentation using sharp indenter geometry has been extensively studied. This work investigates the mechanical properties of TiO2 thin film (1 µm thickness) deposited by spin coating on dual phase Duplex stainless steel and glass substrates. Experiments are carried out with different sharp triangular pyramids (a Cube corner and a Berkovich indenter) using a commercial Nano Indenter® XP apparatus. The substrate effect has been counteracted and an inverse method proposed in literature for bulk material has been adapted to assess the elastoplastic parameters of the tested thin film directly from…
Towards Open Domain Chatbots—A GRU Architecture for Data Driven Conversations
2018
Understanding of textual content, such as topic and intent recognition, is a critical part of chatbots, allowing the chatbot to provide relevant responses. Although successful in several narrow domains, the potential diversity of content in broader and more open domains renders traditional pattern recognition techniques inaccurate. In this paper, we propose a novel deep learning architecture for content recognition that consists of multiple levels of gated recurrent units (GRUs). The architecture is designed to capture complex sentence structure at multiple levels of abstraction, seeking content recognition for very wide domains, through a distributed scalable representation of content. To …
Deposition of binder-free oxygen-vacancies NiCo2O4 based films with hollow microspheres via solution precursor thermal spray for supercapacitors
2019
Abstract Hollow micro-/nanostructures and oxygen vacancies are highly desirable for supercapacitors due to high active surface area and outstanding electrochemical properties. In order to benefiting from the both effect, binder-free oxygen-vacancies NiCo2O4 based films with hollow microspheres were pioneering directly deposited via one kind thermal spray technology, named solution precursor thermal spray (SPTS) process. To our best knowledge, the rapid one-step SPTS route was firstly employed to synthesize and deposit NiCo2O4 films for supercapacitor applications. The CV data clearly demonstrated that the specific capacitances of more oxygen-deficient NiCo2O4 electrodes with hollow microsph…
Optical properties and microstructure of 2.02-3.30 eV ZnCdO nanowires: effect of thermal annealing
2013
International audience; ZnCdO nanowires with up to 45% Cd are demonstrated showing room temperature photoluminescence (PL) down to 2.02 eV and a radiative efficiency similar to that of ZnO nanowires. Analysis of the microstructure in individual nanowires confirms the presence of a single wurtzite phase even at the highest Cd contents, with a homogeneous distribution of Cd both in the longitudinal and transverse directions. Thermal annealing at 550 C yields an overall improvement of the PL, which is blue-shifted as a result of the homogeneous decrease of Cd throughout the nanowire, but the single wurtzite structure is fully maintained.
FOC with Resolver Implementation for PMSM Drives by Using a Low Cost Atmel SAM3X8E Microcontroller
2020
The aim of this paper is the low-cost experimental implementation of a field oriented control strategy for a Permanent Magnet Synchronous Motor (PMSM) by using an Atmel SAM3X8E microcontroller, mounted on an Arduino DUE board. In this electrical drive for PMSM, a resolver is used in order to measure the rotor position and speed: Therefore, the low-cost Arduino DUE performs not only FOC algorithm and phase currents data acquisition, but also a resolver-To-digital converter process, rotor position and speed data acquisition, and resolver signals management. The code has been implemented in the open source Arduino IDE, using C language, whereas the control and plot visualization interfaces hav…
Atomic layer deposition of aluminum oxide on modified steel substrates
2016
Abstract Al 2 O 3 thin films were grown by atomic layer deposition to thicknesses ranging from 10 to 90 nm on flexible steel substrates at 300 °C using Al(CH 3 ) 3 and H 2 O as precursors. The films grown to thicknesses 9–90 nm covered the rough steel surfaces uniformly, allowing reliable evaluation of their dielectric permittivity and electrical current densities with appreciable contact yield. Mechanical behavior of the coatings was evaluated by nanoindentation. The maximum hardness values of the Al 2 O 3 films on steel reached 12 GPa and the elastic modulus exceeded 280 GPa.
Stealth dicing with ultrafast Bessel beams with engineered transverse profiles
2017
International audience; We investigate high-speed glass cleaving with ultrafast laser beams with engineered transverse intensity profile. We achieve accuracy of ~ 1 µm at 25 mm/s and drastically enhance cleavability compared to standard Bessel beams.
High-pressure x-ray-absorption study of GaSe
2002
The III-VI layered semiconductor InSe has been studied by high-pressure single crystal x-ray absorption spectroscopy up to a maximum pressure of 14 GPa. The In-Se distance has been measured in both the low- pressure layered phase and the high-pressure NaCl phase. The bond compressibility in the layered phase is lower than the ``a'' crystallographic parameter compressibility, which implies an increase of the angle between the In-Se bond and the layer plane. Under plausible hypothesis, a description of the evolution of the whole structure with pressure is given. In particular, the intralayer distance is observed to increase with increasing pressure. A plausible precursor defect and a simple m…