Search results for "Microscope"
showing 10 items of 1412 documents
Light induced charging of polymer functionalized nanorods.
2010
ZnO nanorods were functionalized with new block copolymers containing a hole transporting moiety in one block and a dye and an anchor system in the second block. After functionalization, the ZnO nanorods are well dispersible in organic media and the fluorescence of the dye is quenched. Kelvin probe force microscopy was used to measure changes in electrical potential between the ZnO nanorod and the polymeric corona. Upon light irradiation, potential changes on the order of some tens of millivolts were observed on individual structures. This effect is attributed to light-induced charge separation between the ZnO nanorod and its hole transporting polymeric corona.
Forces Between Solid Surfaces Across Polymer Melts as Revealed by Atomic Force Microscopy
2007
Forces between solid surfaces across polymer melts are poorly understood despite their fundamental importance and their relevance for making composite materials. Such force measurements reveal information on the structure of polymers at surfaces and of confined polymers. Experiments with the atomic force microscope and polyisoprene (PI) confirmed theoretical predictions that no long‐range force should be present in thermodynamic equilibrium. In poly(dimethyl siloxane) (PDMS) repulsive forces are observed at high molar mass. We attribute this to the formation of an immobilized layer caused by a slow release of adsorbed segments enhanced by entanglement. In low molar mass PDMS attractive forc…
Inside Front Cover: A Combined Top-Down/Bottom-Up Approach for the Nanoscale Patterning of Spin-Crossover Coordination Polymers (Adv. Mater. 16/2007)
2007
The background scanning electron microscopy image shows nanometric patterns of the 3D spin crossover coordination polymer Fe(pyrazine)[Pt(CN)4] (see schematic structure in the circle), which have been fabricated using a combination of lift-off and multilayer sequential assembly methods. These patterns, reported by Gabor Molnar, Azzedine Bousseksou, and co-workers on p. 2163, exhibit a bistability of their electronic states (1A1 ⇌ 5T2), and thus represent a novel platform for a wide array of potential applications.
Enzyme-Mediated Deposition of a TiO2Coating onto Biofunctionalized WS2 Chalcogenide Nanotubes
2009
A chemically specific and facile method for the biofunctionalization of WS2 nanotubes (NT-WS2) is reported. The covalent modification strategy is based on the affinity of the nitrilotriacetic acid (NTA) side chain, which serves as a ligand for the surface binding to NT-WS2 and simultaneously as an anchor group for the binding of His-tagged proteins to the polymer backbone. The polymer functionalized WS2 nanotubes can be solubilized either in water or organic solvents; they are stable for at least one week. The probes were characterized by FT-IR and UV-vis spectroscopy. The immobilization of silicatein, a hydrolytic protein encountered in marine sponges, was visualized by scanning force micr…
Coherent Electronic Coupling versus Localization in Individual Molecular Dimers
2004
International audience; The electronic excitation transfer and coherent electronic coupling strength were investigated in molecular dimers by spectrally resolved confocal fluorescence spectroscopy. The direct probe of electronic coupling strength distribution was possible due to static disorder in polymer host by single molecule measurements. The dimers with delocalized excitation were also found in comparison to emission originated from localized states. The delocalized and localized state transitions were observed for dimers which were attributed to structural fluctuations of guest-host system.
Different approaches in sulfonated poly (ether ether ketone) conductivity measurements
2019
Ion conductivity of sulfonated poly (ether ether ketone) (SPEEK) membranes with various degree of sulfonation (DS) was investigated using impedance analysis with different measuring cell configuration and ion conductivity was calculated from resistances of polymer membranes. SPEEK was synthesized from poly (ether ether ketone) (PEEK) via sulfonation reaction in concentrated sulfuric acid (95-98%). Scanning electron microscopy (SEM) analysis of membrane surface was performed to determine possible mechanical damage to the membrane during resistance measurements.
PLLA/PLA scaffolds prepared via Thermally Induced Phase Separation (TIPS): tuning of properties and biodegradability
2008
Foams for tissue engineering applications were prepared via thermally induced phase separation (TIPS). Poly-L-Lactic Acid (PLLA) and blends of PLLA with PLA in different proportions were used (100/0, 90/10, 75/25, 50/50, 0/100 PLLA/PLA wt/wt) starting from ternary systems where dioxane was the solvent and water the non-solvent. Morphology was evaluated by Scanning Electron Microscopy (average pore size and interconnection) and the void fraction was measured by means of Hg porosimetry. Foams apparent density was also evaluated (porosity ranges from 87% to 92%). Biodegradability was estimated in a body mimicking fluid. Results show that structure and morphology (in terms of average pore size …
Cellulose-click-ferrocenes as docking spots for cyclodextrin
2012
A novel synthesis of ferrocene-modified cellulose, prepared from 6-azido-6-deoxy-cellulose and ethynylferrocene, is presented. The two components were coupled via copper-catalyzed click-type cycloaddition under microwave-assisted conditions. The surface structure of the cellulose derivative was investigated in comparison with that of pure, microcrystalline cellulose using electron microscopy (scanning, transmission and scanning transmission), showing iron atoms of ferrocene as homogeneously distributed particles. They are detectable as clear signals in the energy-dispersive X-ray profile. In addition, Rame-β-cyclodextrin was supramolecularly attached to cellulose and the complex formed was …
Transmission of mechanical energy through polymeric liquid crystals and their blends
1988
Molecular composites, also called polymeric liquid crystals (PLC), are contrasted with the traditional composites; the name heterogeneous composites is proposed for the latter. Advantages of blending PLCs with ordinary engineering polymers are discussed. Results reported for blends of poly(ethylene terepthalate) (PET) with a PLC containing sequences of PET and p-hydroxybenzoic acid (PHB) include thermophysical properties, melt rheology, mechanical properties of solid blends, and scanning electron microscopy of fracture surfaces. A model called the island model was developed to explain the results: One assumes that the lines of force as well as propagating cracks tend to concentrate in the p…
Identification of Manganese(IV) Centers in Archaeological Glass Using Microsample Coatings Attached to PolymerFilm Electrodes
2001
Identification of MnO2 nodulae in archaeological glass by linear scan and differential pulse voltammetry using abrasive-conditioned microsamples attached to polymer film (Elvacite 2044) electrodes is described. Voltammetric responses for manganese-containing samples parallels to those obtained for β- and γ-MnO2 upon immersion of modified electrodes into NaCl, KCl and acetic/acetate aqueous media. The observed electrochemical response provides information on the open microporous structure of the MnO2 forms and the conditions of their formation during the weathering process of buried glass.