Search results for "NICS"
showing 10 items of 15025 documents
The interdependence of structural and electrical properties in TiO2/TiO/Ti periodic multilayers
2013
International audience; Multilayered structures with 14-50 nm periods composed of titanium and two different titanium oxides, TiO and TiO2, were accurately produced by DC magnetron sputtering using the reactive gas pulsing process. The structure and composition of these periodic TiO2/TiO/Ti stacks were investigated by X-ray diffraction and transmission electronic microscopy techniques. Two crystalline phases, hexagonal close packed Ti and face centred cubic TiO, were identified in the metallic-rich sub-layers, whereas the oxygen-rich ones comprised a mixture of amorphous TiO2 and rutile phase. DC electrical resistivity rho measured for temperatures ranging from 300 to 500 K exhibited a meta…
Experimental studies on uniaxial and echibiaxial tensile tests applied to plastic materials sheets
2019
Abstract The main objective of this paper is to determine the behavior of few plastic materials using two different type of tests. We use classical uniaxial tensile test to determine the most important mechanical and elastic characteristics, such as: yield stress, Young modulus, tangent modulus, maximum stress and maximum strain and to plot engineering stress vs. engineering strain curve for these materials. The second test, that was used in this study, was echibiaxial tensile test on the spherical punch. This test was used to determine maximum breaking force and, of course maximum displacement of specimen on punch direction and others few important characteristics, such as: major and minor…
Fabrication and characterization of low cost Cu 2 O/ZnO:Al solar cells for sustainable photovoltaics with earth abundant materials
2016
Abstract The low cost electrodeposition method was used to grow Cu2O thin films and experimentally determine the optimal absorber layer thickness. Raman scattering studies indicate the presence of solely crystalline Cu2O and SEM images show that the thin films consist of grains with a pyramidal shape. The influence of the thickness of the light absorbing Cu2O layer on the basic characteristic of the heterojunction and their properties have been investigated using reflectivity, current–voltage (J–V), capacitance–voltage (C–V) and the external quantum efficiency (EQE) measurements. The depletion layer, the charge collection length of the minority carrier, and reflectivity are the main factors…
Reactive Sintering of molybdenum disilicide by Spark Plasma Sintering from mechanically activated powder mixtures: Processing parameters and properti…
2008
Abstract Dense molybdenum disilicide with a nano-organized microstructure was synthesized by mechanical activation, by producing nanostructured agglomerates of a 1:2 mixture of Mo and Si, followed by the synthesis/consolidation in one step using SPS technology. In order to synthesize a dense molybdenum disilicide with a perfectly controlled microstructure, an investigation of the influence of Spark Plasma Sintering processing parameters (temperature, heating rate, mechanical pressure and holding time) on the chemical composition and the microstructure characteristics has been performed. The present work shows also that the so-obtained materials present better oxidation resistance in compari…
Modelling of thermal field and point defect dynamics during silicon single crystal growth using CZ technique
2018
Abstract Silicon single crystal growth by the Czochralski (CZ) technique is studied numerically using non-stationary mathematical models which allow to predict the evolution of the CZ system in time, including Dash neck, cone and cylindrical growth stages. The focus is on the point defect dynamics, also considering the effect of the thermal stresses. During the cylindrical stage, the crystal pull rate is temporarily reduced as in experiments by Abe et al. The crystal radius and heater power change is explicitly considered in the calculations for crystal diameters of 50, 100 and 200 mm and the agreement with experiments is discussed.
Effect of process parameters and crystal orientation on 3D anisotropic stress during CZ and FZ growth of silicon
2017
Abstract Simulations of 3D anisotropic stress are carried out in and oriented Si crystals grown by FZ and CZ processes for different diameters, growth rates and process stages. Temperature dependent elastic constants and thermal expansion coefficients are used in the FE simulations. The von Mises stress at the triple point line is ~5–11% higher in crystals compared to crystals. The process parameters have a larger effect on the von Mises stress than the crystal orientation. Generally, the crystal has a higher azimuthal variation of stress along the triple point line (~8%) than the crystal (~2%). The presence of a crystal ridge increases the stress beside the ridge and decreases it on the ri…
Temperature Dependent Suns-V<inf>oc</inf> of Multicrystalline Silicon Solar Cells from Different Ingot Positions
2018
This paper presents temperature dependent Suns- Voc measurements on multicrystalline silicon cells originating from different ingot positions. The effective lifetime is found to increase for all cells when the temperature is increased from 25°C to 6°C. However, cells from the top of the ingot show a considerably larger increas 40–50% for illumination conditions of 0.1-1 Sun, compared to an increase of 20-30% observed for cells from the bottom. The decrease in Voc with increasing temperature is found to be lower for cells from the top of the ingot compared to cells from the bottom. The temperature coefficient of the Voc is found to vary 5% along the ingot at 1 Sun, highlighting the influence…
Mathematical modelling of the feed rod shape in floating zone silicon crystal growth
2017
Abstract A three-dimensional (3D) transient multi-physical model of the feed rod melting in the floating zone (FZ) silicon single-crystal growth process is presented. Coupled temperature, electromagnetic (EM), and melt film simulations are performed for a 4 inch FZ system, and the time evolution of the open melting front is studied. The 3D model uses phase boundaries and parameters from a converged solution of a quasi-stationary axisymmetric (2D) model of the FZ system as initial conditions for the time dependent simulations. A parameter study with different feed rod rotation, crystal pull rates and widths of the inductor main slit is carried out to analyse their influence on the evolution …
Validation of a 3D mathematical model for feed rod melting during floating zone Si crystal growth
2019
Abstract A mathematical model of global 3D heat transfer in floating zone silicon single crystal growth process is used to predict the shape of the open melting front of the feed rod. The model is validated using measurement data from research-scale growth experiments. Shape profiles of the open melting front are obtained from the feed rod leftover using a movable dial gauge. Azimuthal asymmetry of the rim of the open melting front is revealed in both simulations and measurements, quantitatively indicating the influence of the main slit of the inductor.
Choice of the detectors for light impurities plasma studies at W7-X using ‘CO Monitor’ system
2019
Abstarct The ‘CO Monitor’ is a new spectrometer system dedicated for the continuous measurements of line intensities of carbon, oxygen, boron and nitrogen at the fusion plasma experiment Wendelstein 7-X (W7-X). Its main purpose is to deliver constant information about indicated elements with high time resolution (better than 1 ms), but low spatial resolution since the line shapes are not going to be investigated. The system consists of four independent channels, each equipped with dispersive element dedicated for measurement of selected line of interest. In order to perform the highest efficiency of the ‘CO Monitor’ system, it is essential to choose the proper detector type for this task. T…