Search results for "Nondestructive Testing"
showing 10 items of 69 documents
A Numerical Study on Interlaminar Defects Characterization in Fibre Metal Laminates with Flying Laser Spot Thermography
2018
This work describes a numerical study on non-destructive evaluation of interlayer disbond defects in aerospace grade Fibre Metal Laminate sheets (FMLs). A recently proposed infrared non-destructive testing setup is considered, where a continuous laser is moved over the material surface, while the thermal footprint of the moving heat source is acquired, e.g. by an infrared thermal camera. Interlayer disbonds are then detected by analysing the features of the acquired thermograms. The experimental feasibility of this approach has been recently proved. The present work proposes a numerical simulation of the NDT approach, where the material thermal response is analysed and correlated to defects…
Real-time monitoring of graphene patterning with wide-field four-wave mixing microscopy
2016
The single atom thick two-dimensional graphene is a promising material for various applications due to its extraordinary electronic, optical, optoelectronic, and mechanical properties. The demand for developing graphene based applications has entailed a requirement for development of methods for fast imaging techniques for graphene. Here, we demonstrate imaging of graphene with femtosecond wide-field four-wave mixing microscopy. The method provides a sensitive, non-destructive approach for rapid large area characterization of graphene. We show that the method is suitable for online following of a laser patterning process of microscale structures on single-layer graphene. peerReviewed
Real-Time Monitoring of Intergranular Corrosion Damage on AA2024
2017
The total porosity induced by the intergranular corrosion was selected as a monitoring parameter to follow in real-time the defect propagation of AA2024. The pertinence of eddy current (EC) probing has been tested on very thin foils of AA2024 (30 μm in thickness) in immersion conditions under potentiostatic control and in atmospheric conditions simulated by controlled salt spray experiments. Combining this nondestructive evaluation technique with a direct optical interrogation of the backside of the test specimen (derived from the foil penetration technique) allows one to discuss the contribution of both the dissolution in the depth and along the grain boundaries to the total porosity. In i…
Detection of defects buried in metallic samples by scanning microwave microscopy
2011
This paper reports the local detection of buried calibrated metal defects in metal samples by a new experimental technique, scanning microwave microscopy. This technique combines the electromagnetic measurement capabilities of a microwave vector network analyzer with the subnanometer-resolution capabilities of an atomic force microscope. The network analyzer authorizes the use of several frequencies in the range 1--6 GHz, allowing three-dimensional tomographical investigation, which is useful for the detection of bulk defects in metal materials.
Microfocus X-ray computed tomography analysis of corroded glass objects
2009
Abstract Microfocus X-ray computed tomography (µCT) is a useful tool for non-destructive analysis of corroded archaeological glass objects and for monitoring restoration and conservation processes for these materials. This was demonstrated by µCT analysis of artificially corroded laboratory-produced glasses and corroded archaeological glasses retrieved from soil environments. Corrosion layers with a thickness of 20 µm or more can be detected as areas with lower X-ray attenuation values than the non-corroded glass. Features that are revealed by µCT analyses include the degree and patterns of corrosion and the presence of various internal structures in the corrosion layers. The study of resto…
Robotic path planning for non-destructive testing – A custom MATLAB toolbox approach
2016
AbstractThe requirement to increase inspection speeds for non-destructive testing (NDT) of composite aerospace parts is common to many manufacturers. The prevalence of complex curved surfaces in the industry provides motivation for the use of 6 axis robots in these inspections. The purpose of this paper is to present work undertaken for the development of a KUKA robot manipulator based automated NDT system. A new software solution is presented that enables flexible trajectory planning to be accomplished for the inspection of complex curved surfaces often encountered in engineering production. The techniques and issues associated with conventional manual inspection techniques and automated s…
Investigating the effect of residual stress on hydrogen cracking in multi-pass robotic welding through process compatible non-destructive testing
2021
Abstract In this paper, the effect of Welding Residual Stress (WRS) on the size and morphology of hydrogen-induced cracks (HIC) is studied. Four samples were manufactured using a 6-axis welding robot and in two separate batches. The difference between the two batches was the clamping system used, which resulted in different amounts of welding deformation and WRS. The hydrogen cracks were intentionally manufactured in the samples using a localised water-quenching method, where water was sprayed over a specific weld pass in a predetermined position. The Phased-Array Ultrasonic Testing (PAUT) system was implemented during the welding process (high-temperature in-process method), to detect the …
Multiscale microstructural characterization of particulate-reinforced composite with non-destructive X-ray micro- and nanotomography
2018
Abstract Methods based on X-ray tomography are developed to study the relevant statistical quantities describing the microstructural inhomogeneity of particulate reinforced composites. The developed methods are applied in estimating microstructural inhomogeneity parameters of composites containing metallic glass particles in metal matrix, extruded in varying pressure loads. This study indicates that the critical characteristics with regard to the effect of particle clustering are cluster size and shape, local volume fraction of particles in the cluster and the distance between clusters. The results demonstrate that the spatial distribution of reinforcement is very uneven and the amount of p…
Crack detection using electrostatic measurements
2001
In this paper we extend recent work on the detection of inclusions using electrostatic measurements to the problem of crack detection in a two-dimensional object. As in the inclusion case our method is based on a factorization of the difference between two Neumann-Dirichlet operators. The factorization possible in the case of cracks is much simpler than that for inclusions and the analysis is greatly simplified. However, the directional information carried by the crack makes the practical implementation of our algorithm more computationally demanding.
Ultrasonic Guided Wave Inspection of Bonded Lap Joints: Noncontact Method and Photoelastic Visualization
2001
The main topic of this paper is the nondestructive inspection of adhesively bonded lap joints by using ultrasonic guided (plate) waves. A noncontact, couplant-free method that employs capacitive air-coupled transducers is demonstrated for the inspection of thin aluminum joints with dimensions typical of aircraft fuselage and wing panels. Two types of bond defects, disbonded regions and regions of poorly cured (low-cohesive-strength) adhesive, are successfully detected by measuring the amplitude decrease of selected plate waves leaking from one adherend to the other one through the bondline. It is shown that proper choice of the vibrating mode structure, in terms of cross-sectional displacem…