Search results for "Parameters"
showing 10 items of 13273 documents
Non-destructive Approach to Multilayer Objects: XRF Analysis of Gilt and Enamelled Metals of the Medieval Cross of Rosciolo
2013
Abstract The penetration of X-rays is usually a limitation to the application of XRF analysis to multilayered materials, however it is possible, by software tools based on the fundamental parameters method, to overcome this problem and estimate thickness and composition of each layer. The cross of Rosciolo is a significant example of multilayer object: it is made of a wood core with attached gilt silver sheets and decorated with enamels. Measurements were carried out in situ and the PyMCA software was employed. The values of gilding thickness, Au/Hg ratios and Cu content in the silver sheets, and enamel's composition are discussed.
X-ray fluorescence investigation of gilded and enamelled silver: The case study of four medieval processional crosses from central Italy
2013
Abstract The presence of multilayered structures is common in such cultural artefacts as paintings, corroded metals, objects that underwent a whatever form of surface qualification. One of the most usual and complete ways to investigate such structures is observing a cross section, which requires sampling. There are however situations where at least part of the stratigraphic information can be derived non-destructively: the literature shows that X-ray fluorescence (XRF) has frequently been used, in recent years, for this purpose, with special regard to paintings and gilded metals. Aim of this paper is to further explore the suitability of XRF-based techniques to characterise multilayered st…
Study of Gasdynamic Electron Cyclotron Resonance Plasma Vacuum Ultraviolet Emission to Optimize Negative Hydrogen Ion Production Efficiency
2019
Negative hydrogen ion sources are used as injectors into accelerators and drive the neutral beam heating in ITER. Certain processes in low-temperature hydrogen plasmas are accompanied by the emission of vacuum ultraviolet (VUV) emission. Studying the VUV radiation therefore provides volumetric rates of plasma-chemical processes and plasma parameters. In the past we have used gasdynamic ECR discharge for volumetric negative ion production and investigated the dependencies between the extracted H$^-$ current density and various ion source parameters. It was shown that it is possible to reach up to 80 mA/cm$^2$ of negative ion current density with a two electrode extraction. We report experime…
Electronic Structure Changes across the Metamagnetic Transition in FeRh via Hard X-Ray Photoemission
2012
International audience; Stoichiometric FeRh undergoes a temperature-induced antiferromagnetic (AFM) to ferromagnetic (FM) transition at similar to 350 K. In this Letter, changes in the electronic structure accompanying this transition are investigated in epitaxial FeRh thin films via bulk-sensitive valence-band and core-level hard x-ray photoelectron spectroscopy with a photon energy of 5.95 keV. Clear differences between the AFM and FM states are observed across the entire valence-band spectrum and these are well reproduced using density-functional theory. Changes in the 2p core levels of Fe are also observed and interpreted using Anderson impurity model calculations. These results indicat…
First experiments with gasdynamic ion source in CW mode.
2016
A new type of ECR ion source—a gasdynamic ECR ion source—has been recently developed at the Institute of Applied Physics. The main advantages of such device are extremely high ion beam current with a current density up to 600–700 emA/cm2 in combination with low emittance, i.e., normalized RMS emittance below 0.1 π mm mrad. Previous investigations were carried out in pulsed operation with 37.5 or 75 GHz gyrotron radiation with power up to 100 kW at SMIS 37 experimental facility. The present work demonstrates the first experience of operating the gasdynamic ECR ion source in CW mode. A test bench of SMIS 24 facility has been developed at IAP RAS. 24 GHz radiation of CW gyrotron was used for p…
Influence of machining parameters on surface roughness in WEDM cutting
2020
Wire Electrical Discharge Machining is a cutting method used for obtaining parts with complex geometries or for cutting hard metals. This рарer ѕeekѕ to emрhаѕіze the іmрortаnce of thіѕ unconventіonаl technology аnd more ѕрecіfіcаlly the іmрortаnce of knowіng the раrаmeterѕ of а рroceѕѕ before рlаnnіng the рroductіon of а benchmаrk. Cylіndrіcаl metаl cаrbіde раrtѕ wіth а hаrdneѕѕ of 1620 HV / 92 HRC were cut durіng the analysis9, uѕіng the mіnіmum аnd mаxіmum vаlueѕ of the cutting раrаmeterѕ: wire feed rаte, wire rotаtіon ѕрeed, wіre tenѕіon, dіelectrіc рreѕѕure, electrіcаl current(Α) аnd electrіcаl рotentіаl (V). The roughneѕѕ of the obtаіned ѕurfаceѕ has been meаѕured after being cut аnd …
Quasi-static magnetoresistive sensor modeling for current-time conversion circuit applications
2011
In this paper we report a current-to-time converter (CTC) suitable for current sensor monitoring in low power applications. Based on a discrete resistence-to-frequency converter and a Giant MagnetoResistance (GMR) current sensor. Simulations have been done using a quasi-static electrical Verilog-A model for the GMR current sensor. A reduced set of parameters has been extracted to characterize the GMR sensor's behavior. The application has been analyzed making use of different sensors, whose device parameters were previously extracted. Finally, the accuracy of the models has been tested by comparing with experimental transient measurements.
Optimisation of TA6V alloy surface laser texturing using an experimental design approach
2008
International audience; Active surfaces of plastic injection moulds are nowadays textured using classical techniques (chemical etching or EDM). Replacement of these technologies by a laser technology introduces a big flexibility: absence of mechanical contact with the tool, decrease of the effluent's volume and a big machining precision, even in the case of the complex forms as injection moulds for example. This paper reports the experimental study of the surface laser texturing of TA6V alloy. The influence of the operating factors on the laser texturing process has been studied using two experimental approaches: Taguchi methodology and response surface methodology (RSM). Empirical models h…
Microwave characterization and modeling of packaged HEMTs by a direct extraction procedure at cryogenic temperatures
2004
In the present work we employ a direct extraction procedure to determine small signal equivalent circuit of microwave GaAs FETs by means of scattering (S-) parameter measurements down to cryogenic temperatures. The direct extraction procedure was tested on packaged AlGaAs/InGaAs HEMTs and good agreement between the simulated and measured S-parameters was obtained at different bias and temperature conditions. We employed a properly designed cryogenic set-up operating in our laboratory that allows to perform DC and RF characterization down to 30 K.
A procedure to achieve fine control in MW processing of foods
2007
Abstract A two-dimensional analytical model for predicting the unsteady temperature field in a cylindrical shaped body affected by spatially varying heat generation is presented. The dimensionless problem is solved analytically by using both partial solutions and the variation of parameters techniques. Having in mind industrial microwave heating for food pasteurization, the easy-to-handle solution is used to confirm the intrinsic lack of spatial uniformity of such a treatment in comparison to the traditional one. From an experimental point of view, a batch pasteurization treatment was realized to compare the effect of two different control techniques both based on IR thermography readout: t…