Search results for "Signal"
showing 10 items of 6924 documents
IL-6 trans-Signaling
2004
The molecular consequence of the fever response has been illuminated by a recent study showing that a temperature shift to 40 degrees C resulted in increased leukocyte adhesion to tissue sections, which was mediated by L-selectin activation in lymphocytes. This L-selectin activation during heat responses was dependent on IL-6 trans-signaling via the soluble IL-6R.
Depth profiling of Al2O3 + TiO2 nanolaminates by means of a time-of-flight energy spectrometer
2011
Atomic layer deposition (ALD) is currently a widespread method to grow conformal thin films with a sub-nm thickness control. By using ALD for nanolaminate oxides, it is possible to fine tune the electrical, optical and mechanical properties of thin films. In this study the elemental depth profiles and surface roughnesses were determined for Al2O3 + TiO2 nanolaminates with nominal single-layer thicknesses of 1, 2, 5, 10 and 20 nm and total thickness between 40 nm and 60 nm. The depth profiles were measured by means of a time-of-flight elastic recoil detection analysis (ToF-ERDA) spectrometer recently installed at the University of Jyväskylä. In TOF-E measurements 63Cu, 35Cl, 12C and 4He ions…
Chloroplast signal length requirement reflects the outer membrane and TOC complex dimension
2015
Background and Purpose: The evolution of an efficient preprotein targeting and translocation system was a central prerequisite for the endosymbiotic integration of a -proteobacteria and cyanobacteria as cellular organelles. Today, it is widely accepted that during evolution most (pre-)proteins destined for these two organelles were equipped with an N-terminal targeting signal for localization. While multiple modes of evolution of these extensions are currently discussed, all evolved signals serve the same function – forming a signal for targeting to the correct organelle and translocation across both membranes. We aimed to generalize the current idea for the length requirement of the N-term…
Blind Radio Tomography
2018
From the attenuation measurements collected by a network of spatially distributed sensors, radio tomography constructs spatial loss fields (SLFs) that quantify absorption of radiofrequency waves at each location. These SLFs can be used for interference prediction in (possibly cognitive) wireless communication networks, for environmental monitoring or intrusion detection in surveillance applications, for through-the-wall imaging, for survivor localization after earthquakes or fires, etc. The cornerstone of radio tomography is to model attenuation as the bidimensional integral of the SLF of interest scaled by a weight function. Unfortunately, existing approaches (i) rely on heuristic assumpti…
Measurement of thett¯production cross section inpp¯collisions ats=1.96 TeVusing soft electronb-tagging
2010
The authors present a measurement of the t{bar t} production cross section using events with one charged lepton and jets from p{bar p} collisions at a center-of-mass energy of 1.96 TeV. A b-tagging algorithm based on the probability of displaced tracks coming from the event interaction vertex is applied to identify b quarks from top decay. Using 318 pb{sup -1} of data collected with the CDF II detector, they measure the t{bar t} production cross section in events with at least one restrictive (tight) b-tagged jet and obtain 8.9{sub -1.0}{sup +1.0}(stat.){sub -1.0}{sup +1.1}(syst.) pb. The cross section value assumes a top quark mass of m{sub t} is presented in the paper. This result is cons…
The Measurement of Reactive Energy in Polluted Distribution Power Systems: An Analysis of the Performance of Commercial Static Meters
2008
This paper presents a comparative analysis of the performances of both a traditional induction meter and various types of commercial static meters for reactive energy in the presence of harmonic distortion. This is a topical issue, since there are several types of static meters on the market, based on different principles of construction. In accordance with current standards, these meters are designed to operate in sinusoidal conditions and their performance is not tested in the presence of harmonic distortion. However, with the increase of pollution levels in power systems, the meters may be used even in the presence of distorted voltages and/or currents; in such cases, their accuracy may …
Improved Switching Strategy for Selective Harmonic Elimination in DC-AC Signal Generation via Pulse-Width Modulation
2013
Published version of an article in the journal: Abstract and Applied Analysis. Also available from the publisher at: http://dx.doi.org/10.1155/2013/870904 Open Access We present an advanced design methodology for pulse-width-modulated (PWM) DC-AC signal generation. Using design methods based on the Walsh transform, AC sinusoidal signals can be approximated by suitable PWM signals. For different AC amplitudes, the switching instants of the PWM signals can be efficiently computed by using appropriate systems of explicit linear equations. However, the equation systems provided by conventional implementations of this approach are typically only valid for a restricted interval of AC amplitudes a…
EFFECTS OF THE MULTIPLE INTERNAL REFLECTION AND SAMPLE THICKNESS CHANGES ON DETERMINATION OF ELECTRO-OPTIC COEFFICIENT VALUES OF A POLYMER FILM
2012
New nonlinear optical (NLO) active organic materials are appealing candidates for optoelectronic and photonic technologies. For the evaluation of new NLO polymer materials for applicability in the mentioned technologies, the most important criteria are their electro-optic (EO) coefficients. We have implemented the Mach–Zehnder interferometric (MZI) method for the determination of EO coefficients of thin organic films. Despite the fact that other multiple optical methods for the determination of thin film EO coefficients are known, the MZI method has been chosen because this particular technique has high sensitivity to phase and intensity modulations in the sample arm of an interferometer an…
Review and comparison of experimental techniques used for determination of thin film electro-optic coefficients
2015
The results of electro-optic coefficient measurements performed with three commonly applied techniques used to assess electro-optic coefficients: the Mach–Zehnder, the Teng–Man, and the attenuated total reflectance technique are reported. It is shown that the signal obtained by the Mach–Zehnder and Teng–Man techniques is strongly influenced by the multiple internal reflection and piezo- and electrostrictive thickness change effects, which in our opinion have not been addressed sufficiently in the literature. A novel approach based on using Abeles matrix formalism is implemented for the retrieval of electro-optic coefficients from experimental data. The measurement results, errors, and compa…
Comparison of total-reflection X-ray fluorescence, static and portable energy dispersive X-ray fluorescence spectrometers for art and archeometry stu…
2004
Abstract In this paper, a Total-reflection X-ray Fluorescence (TXRF), a static and a portable Energy Dispersive X-ray Fluorescence (EDXRF) spectrometers are described. Both the equipments and the techniques employed in the field of the art and archeometry are compared. Some applications in this area are presented as well. The aim of the work is to know which spectrometer is the best suited depending on the work of art and the problem treated. The conclusion reached from the experience is that the portable EDXRF spectrometer is advisable to make “in situ” and online analysis in a multidisciplinary environment, the static EDXRF equipment is good to perform analysis on paper and metal pieces a…