Search results for "Systems Engineering"
showing 10 items of 1230 documents
Mechanical behaviour and failure modes of metal to composite adhesive joints for nautical applications
2010
In this paper, the influence of several parameters on the mechanical behaviour and failure modes of hybrid bonded joints aluminium/composite was investigated. Particularly, the effects of metallic surface condition, adhesive properties and thickness on single-lap joint resistance were analysed. To these aims, two adhesives were used and, for each adhesive, two different adhesive thicknesses (0.5 and 1.5 mm) have been investigated. Furthermore, two sets of joints for each adhesive kind and thickness were investigated: the former was obtained using aluminium blanks which were previously mechanically treated with sandpaper (P60) and the latter using aluminium treated with sandpaper and with pr…
Processing and properties of nanocrystalline Pb(Sc0.5Ta0.5)O3, Pb(Sc0.5nb0.5)O3 and Pb(Mg1/3Nb2/3)O3 films produced by RF-sputtering from ceramic tar…
2000
Abstract Nanocrystalline thin films of different relaxor materials, namely Pb(Sc0.5Ta0.5)O3 (PST), Pb(Sc0.5Nb0.5)O3(PSN), Pb(Mg1/3Nb2/3)O3(PMN) have been produced by RF-sputtering to investigate whether it will affect their dielectric properties if their grain size is reduced to the dimensions known from their nanodomains. The XRD shows that the amorphous film crystallizes in pyrochlore structure at lower temperatures and short times. Annealing at higher temperatures and far longer time intervals leads to an increasing amount of perovskite phase with a grain size in the nanometer range. These results including dielectric measurements will be presented and discussed.
Dielectric properties of reactor irradiated ferroelectric thin films
2001
Abstract Radiation effects in highly oriented Pb1Zr0.53Ti0.47O3 (PZT), Pb0.94La0.06Zr0.65Ti0.35O3 (PLZT-6), and PbiZriO3 (PZ) ferroelectric (FE) and antiferroelectric (AF) thin films are investigated in view of their possible application as a temperature sensitive element in a new bolometer system for ITER (International Thermonuclear Experimental Reactor). The dielectric properties (i.e. hysteresis loops, dielectric constants) of the films were investigated in a frequency range from 20 to 105 Hz and at temperatures up to 450 °C, before and after neutron irradiation to a neutron fluence of 5×1021 m−2 (E<0.1 MeV). The dielectric constant was measured during cooling with 1.7 °Cmin−1. The diel…
Comparing different processing methods in apple slice drying. Part 1. Performance of microwave, hot air and hybrid methods at constant temperatures
2019
The drying curves, energy efficiency and colour variations of sliced apples dried at various temperatures and using different techniques were evaluated, i.e. microwave (35, 55 and 65 °C), hot air (35, 55, 65 and 75 °C) and combination of both (65 °C). The microwave (MW) tests also included comparison between air recirculation and continuous inlet of fresh air. Each drying method was evaluated at a fixed temperature level by means of a control system based on infrared thermography. The time required to complete the drying process at 65 °C varied from about 44 min for MW with fresh air ventilation (double with air recirculation), to 122 min for hybrid heating and 238 min for hot air. Drying k…
Characterization of the Optimal Damping Coefficient in the Continuous Contact Model
2020
AbstractThis paper presents an analytical formula to characterize the damping coefficient as a function of system's parameters in a continuous force model of impact. The contact force element consists of a linear damper which is in a parallel connection to a spring with Hertz force-deformation characteristic. Unlike the existing models in which the separation condition is assumed to be at the time at which both zero penetration (deformation) and zero force occur, in this study, only zero contact force is considered as the separation condition. To ensure that the continuous contact model obtains the desired restitution, an optimization process is performed to find the equivalent damping coef…
Ru-Based Thin Film Temperature Sensor for Space Environments: Microfabrication and Characterization under Total Ionizing Dose
2016
The paper shows the microfabrication processes of a Ruthenium-based resistance temperature detector and its behavior in response to irradiation at ambient temperature. The radiation test was done in a public hospital facility and followed the procedures based on the ESA specification ESCC 22900. The instrumentation system used for the test is detailed in the work describing the sensors resistance evolution before, during, and after the exposure. A total irradiation dose of 43 krad with 36 krad/h dose rate was applied and a subsequent characterization was performed once the Ru sensors were submitted to an 80°C annealing process during a period of 168 h. The experimental measurements have sho…
Temperature Sensor Based on Ge-Doped Microstructured Fibers
2009
The fundamental mode cutoff properties of Ge-doped microstructured fibers, filled with a liquid, permit the implementation of wavelength- and amplitude-encoded temperature sensors with an ultra-high sensitivity. The cutoff wavelength changes with temperature, and the thermo-optic coefficient of the liquid determines the sensitivity of the sensor. Sensitivity as high as 25 nm/∘Cis reported. In addition, simple amplitude interrogation techniques can be implemented using the same sensor heads.
Influence of Axial Pressure on the Electrical Properties of Li0.06Na0.94NbO3 Ceramic
2011
Lead-free ceramic Li0.06Na0.94NbO3 was synthesized using a conventional solid-state processing. The single-phase perovskite structure was identified by X-ray powder diffraction technique. The values of lattice parameters of Li0.06Na0.94NbO3 are lower than those for pure NaNbO3. The EDS analysis shows the fairly homogeneous distribution of all elements throughout the grains. An axial pressure significantly influences electric properties. With increasing pressure the peak intensity in the ϵ(T) curve decreases, the peak becomes diffused and shifts to a lower temperature. The value of tanδ increases with increasing axial pressure and its local maximum shifts towards lower temperatures.
Oil whip-induced wear in journal bearings
2014
Published version of an article in the journal: International Journal of Advanced Manufacturing Technology. Also available from the publisher at: http://dx.doi.org/10.1007/s00170-014-5805-8 This paper investigates the effect of oil whirl and oil whip in fluid film radial bearings due to possible metallic contact. The degree of metallic contact and thereby wear and tear between rotating shafts and bearing bushes is assessed by measuring electric currents through the oil film. The current as well as the voltage varied in accordance with the contact ratio between the shaft and bush in the fluid film radial bearing. The gauge signal thus indicates the degree of metallic contact based on the thi…
First-principles modeling of oxygen interaction with SrTiO3(001) surface: Comparative density-functional LCAO and plane-wave study
2011
Large scale first-principles calculations based on density functional theory (DFT) employing two different methods (atomic orbitals and plane wave basis sets) were used to study the energetics, geometry, the electronic charge redistribution and migration for adsorbed atomic and molecular oxygen on defect-free SrTiO3(001) surfaces (both SrO- and TiO2-terminated), which serves as a prototype for many ABO3-type perovskites. Both methods predict substantial binding energies for atomic O adsorption at the bridge position between the oxygen surface ions and an adjacent metal ion. A strong chemisorption is caused by formation of a surface molecular peroxide ion. In contrast, the neutral molecular …