Search results for "Toe"
showing 10 items of 3824 documents
Structural and thermal stability of graphene oxide-silica nanoparticles nanocomposites
2017
Abstract The investigation of the thermal stability up to 400 °C of Graphene Oxide (GO) and GO-silica nanoparticles (n-SiO2) composites prepared by direct mixture of GO and n-SiO2 is reported. Using Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy, Energy Dispersive X-ray analysis, Atomic Force Microscopy, Raman and Infrared absorption measurements a thorough characterization of the prepared materials is carried out. By deepening the changes induced in the 2D Raman spectral region of GO at about 2900 cm−1 the comprehension of an interplay, driven by the thermally induced changes of the material, between inter-valley and intra-valley vibrational transitions is elucidated. This …
Resistive switching in microscale anodic titanium dioxide-based memristors
2018
Licence CC BY-NC-ND The potentiality of anodic TiO2 as an oxide material for the realization of resistive switching memory cells has been explored in this paper. Cu/anodic-TiO2/Ti memristors of different sizes, ranging from 1 × 1 μm2 to 10 × 10 μm2 have been fabricated and characterized. The oxide films were grown by anodizing Ti films, using three different process conditions. Measured IV curves have shown similar asymmetric bipolar hysteresis behaviors in all the tested devices, with a gradual switching from the high resistance state to the low resistance state and vice versa, and a R_OFF/R_ON ratio of 80 for the thickest oxide film devices.
Optical modeling of nickel-base alloys oxidized in pressurized water reactor
2012
International audience; The knowledge of the aging process involved in the primary water of pressurized water reactor entails investigating a mixed growth mechanism in the corrosion of nickel-base alloys. A mixed growth induces an anionic inner oxide and a cationic diffusion parallel to a dissolution-precipitation process forms the outer zone. The in situ monitoring of the oxidation kinetics requires the modeling of the oxide layer stratification with the full knowledge of the optical constants related to each component. Here, we report the dielectric constants of the alloys 600 and 690 measured by spectroscopic ellipsometry and fitted to a Drude-Lorentz model. A robust optical stratificati…
Donor–Acceptor Interfaces by Engineered Nanoparticles Assemblies for Enhanced Efficiency in Plastic Planar Heterojunction Solar Cells
2016
Precisely positioning functionalized gold nanoparticles assemblies at planar donor-acceptor interfaces results in 14-fold enhancement of power conversion efficiency in P3HT/PCBM organic solar cells on plastic (ITO/PET) substrates. This result has been achieved by employing naphthalenethiol-capped gold nanoparticles (NT-Au-NPs) produced by laser ablation in liquid and size varied in the 10-30 nm range. Upon surface functionalization with the aromatic thiol, these particles self-assemble in submicrometer aggregates, which give increased light scattering. When these aggregates are deposited in the planar heterojunction between the donor and the acceptor systems, the localized scattering leads …
Oxide-based nanomaterials for fuel cell catalysis:the interplay between supported single Pt atoms and particles
2017
The concept of single atom catalysis offers maximum noble metal efficiency for the development of low-cost catalytic materials. Among possible applications are catalytic materials for proton exchange membrane fuel cells. In the present review, recent efforts towards the fabrication of single atom catalysts on nanostructured ceria and their reactivity are discussed in the prospect of their employment as anode catalysts. The remarkable performance and the durability of the ceria-based anode catalysts with ultra-low Pt loading result from the interplay between two states associated with supported atomically dispersed Pt and sub-nanometer Pt particles. The occurrence of these two states is a co…
Ultrafast spectroscopic investigation on fluorescent carbon nanodots: the role of passivation.
2019
Disentangling the respective roles of the surface and core structures in the photocycle of carbon nanodots is a critical open problem in carbon nanoscience. While the need of passivating carbon dot surfaces to obtain efficiently emitting nanoparticles is very well-known in the literature, it is unclear if passivation introduces entirely new surface emitting states, or if it stabilizes existing states making them fluorescent. In this multi-technique femtosecond spectroscopy study, the relaxation dynamics of non-luminescent (non-passivated) carbon dots are directly compared with their luminescent (passivated) counterparts. Non-passivated dots are found to host emissive states, albeit very sho…
Two birds with one stone: dual grain-boundary and interface passivation enables >22% efficient inverted methylammonium-free perovskite solar cells
2021
Advancing inverted (p���i���n) perovskite solar cells (PSCs) is key to further enhance the power conversion efficiency (PCE) and stability of flexible and perovskite-based tandem photovoltaics. Yet, the presence of defects at grain boundaries and in particular interfacial recombination at the perovskite/electron transporting layer interface induce severe non-radiative recombination losses, limiting the open-circuit voltage (VOC) and fill factor (FF) of PSCs in this architecture. In this work, we introduce a dual passivation strategy using the long chain alkylammonium salt phenethylammonium chloride (PEACl) both as an additive and for surface treatment to simultaneously passivate the grain b…
Investigation of pitting resistance of titanium based on a modified point defect model
2011
Abstract The pitting resistance of titanium was studied under potential control in solutions containing chloride ions. The results evidenced that Cl − concentration had an effect on the metastable pitting intensity, but no significant influence on the uniform corrosion. XPS characterization revealed that some Cl − ions were present in the outer hydroxide layer, but few in the inner oxide layer, indicating that the inner oxide layer was impervious to Cl − ions. A cation–anion-vacancy condensation mechanism was considered for pit initiation based on the point defect model (PDM). The experimental results analyzed by the charge integration technique were in agreement with the derived relations.
Tuning Charge Carrier Dynamics and Surface Passivation in Organolead Halide Perovskites with Capping Ligands and Metal Oxide Interfaces
2018
Organolead halide perovskites have emerged as exciting optoelectronic materials but a complete understanding of their photophysical properties is still lacking. Here, a morphological series of methylammonium lead bromide (MAPbBr 3 ) perovskites are studied by transient optical spectroscopies over eight orders of magnitude in timescale to investigate the effect of nanostructuring and surface states on the charge carrier dynamics. The sample preparation route and corresponding morphology changes influence the position of the optical features, recombination dynamics, excitation fluence dependence, and dramatically impact surface trap passivation. Growth of the perovskite layer in the presence …
New process of silicon carbide purification intended for silicon passivation
2017
Abstract In this work, we report on a new, efficient and low cost process of silicon carbide (SiC) powder purification intended to be used in photovoltaic applications. This process consists on the preparation of porous silicon carbide layers followed by a photo-thermal annealing under oxygen atmosphere and chemical treatment. The effect of etching time on impurities removal efficiency was studied. Inductively coupled plasma atomic emission spectrometry (ICP-AES) results showed that the best result was achieved for an etching time of 10 min followed by gettering at 900 °C during 1 h. SiC purity is improved from 3N (99.9771%) to 4N (99.9946%). Silicon carbide thin films were deposited onto s…