Search results for "anodizing"
showing 10 items of 116 documents
Tuning of the Mg Alloy AZ31 Anodizing Process for Biodegradable Implants
2021
Coatings were grown on the AZ31 Mg alloy by a hard anodizing process in the hot glycerol phosphate-containing electrolyte. Anodizing conditions were optimized, maximizing corrosion resistance estimated by impedance measurements carried out in Hank's solution at 37 °C. A post anodizing annealing treatment (350 °C for 24 h) allowed us to further enhance the corrosion resistance of the coatings mainly containing magnesium phosphate according to energy-dispersive X-ray spectroscopy and Raman analyses. Gravimetric measurements revealed a hydrogen evolution rate within the limits acceptable for application of AZ31 in biomedical devices. In vitro tests demonstrated that the coatings are biocompati…
Influence of nanoporous structure on mechanical strength of aluminium and aluminium alloy adhesive structural joints
2006
The influence of surface treatments on the mechanical strength of adhesive joints was investigated. The attention was focused on AA2024 alloy because it is extensively used in both the automotive and aerospace industries. Adhesive joints fabricated with pure aluminium were also investigated in order to evidence possible differences in the surface features after identical treatments. Before joining with a commercial epoxy adhesive, metal substrates were subjected to different kinds of treatment and the surfaces were characterized by SEM analysis. The formation of a microporous surface in the AA2024 alloy, upon etching and anodizing, is discussed on the basis of the role of the intermetallic …
The influence of composition on band gap and dielectric constant of anodic Al-Ta mixed oxides
2015
Al-Ta mixed oxides were grown by anodizing sputter-deposited Al-Ta alloys of different composition. Photocurrent spectra revealed a band gap, Eg, slightly independent on Ta content and very close to that of anodic Ta2O5 (∼4.3 eV) with the exception of the anodic film on Al-10at% Ta, which resulted to be not photoactive under strong anodic polarization. The photoelectrochemical characterization allowed to estimate also the oxides flat band potential and to get the necessary information to sketch the energetic of the metal/oxide/electrolyte interfaces. Impedance measurements allowed to confirm the formation of insulating material and to estimate the dielectric constant of the oxides, which re…
Tailoring of the Solid State Properties of Al–Nb Mixed Oxides: A Photoelectrochemical Study
2013
Al–Nb containing mixed oxides were grown by anodizing sputter-deposited Al–Nb alloys of different compositions. A photoelectrochemical investigation was carried out in order to estimate the band gap, flat band potential, and conductivity type of these oxides as a function of their composition. The dependence of the band gap on the composition of mixed sp–d metal oxides has been rationalized by using a semiempirical correlation between the difference of electronegativity and band gap of oxides proposed in the literature some years ago and recently tested for regular d–d metal mixed oxides. The band gap increase observed as a function of Al content into the oxides seems mainly depending on th…
Anodic alumina membranes as template for the synthesis of 1-D metal oxide and hydroxide nanostructures
2008
Anodic alumina membranes with highly ordered cylindrical pores and tuneable geometry have been prepared (pore diameters=20−200 nm; pore density 1012-1014 pores/m2; thickness: 20-100 mm) by controlling the anodizing process of aluminum in phosphoric, oxalic and sulphuric acid. The influence of different parameters (initial treatment of aluminium surface, composition of electrolyte, temperature and applied potential) on the final characteristics of the membranes have been investigated. The use anodic alumina membranes as template for the electrosynthesis of some metal hydroxides and oxides 1-D nanostructures (nanowires and nanotubes) will be also proved.
Luminescence of Eu ion in alumina prepared by plasma electrolytic oxidation
2015
Abstract Eu ion luminescence in aluminium oxide nanocrystals and layers prepared by plasma electrolytic oxidation (PEO) are investigated in this study. The Eu ion in PEO coatings has intense luminescence allowing such material to be used for preparation of various phosphor materials. In this study, Eu ion doped coatings were prepared with two methods: anodization and pulsed bipolar plasma electrolytic oxidation. Also, for comparative studies, alumina nanocrystals with the same amount of Eu ions were prepared using Sol Gel and molten salts methods. Obtained Eu-doped coatings were studied using luminescence methods. Typical Eu ion luminescence bands were observed, however intensity and spectr…
Physicochemical characterization and photoelectrochemical analysis of iron oxide films
2013
Iron oxide films with a nanoporous structure were grown by anodizing sputter-deposited Fe in a fluoride containing ethylene glycol solution and annealed under air exposure at different temperatures. X-ray diffraction and Raman spectroscopy allowed to identify the presence of hematite and/or magnetite after thermal treatment for films annealed at T ≥ 400 °C under air exposure. According to GDOES compositional depth profiles, the thermal treatment sensitively reduced the amount of fluoride species incorporated into the film during the anodizing process. A band gap value of ~2.0 eV was estimated for all the investigated layers, while a flat band potential dependent on both the growth condition…
The influence of thickness, interpore distance and compositional structure on the optical properties of self-ordered anodic aluminum oxide films
2016
Highly ordered anodic aluminum oxide (AAO) films were fabricated using a two-step anodization process in oxalic acid, sulfuric acid, or ethylene glycol containing sulfuric acid, which are important in design of nanostructured optical devices. The morphology and UV-Vis reflectance spectroscopy of these films were analyzed. The morphological parameters of the AAO films, such as the thickness, pore diameter, interpore distance, porosity, pore arrangement regularity, and anodization electrolyte, were adjusted in order to study the effect of these parameters on the UV-Vis reflectance properties of these films. Raman spectroscopy measurements were then utilized to better understand the chemical d…
Ultrathin Anodic Aluminum Oxide Membranes for Production of Dense Sub-20 nm Nanoparticle Arrays
2014
We present a systematic study of membrane structure (pore diameter and arrangement) in anodized aluminum oxide (AAO) layers obtained by anodization voltages 8-20 V in sulfuric and 15-40 V in oxalic acid electrolyte solutions. Anodization of bulk aluminum in sulfuric acid at 10 V potential was found to be optimal for production or ultrathin freestanding membranes with pore diameter in sub-20 nm range. The developed process with slow electrochemical reaction results in AAO membranes with thickness below 70 nm. The minimum required time for formation of continuous AAO membrane was determined and influence of electrolyte concentration on pore diameter in membrane after barrier layer removal ana…
Anodic oxide films on tungsten—I. The influence of anodizing parameters on charging curves and film composition
1980
Abstract The formation of anodic films on tungsten has been studied in 1N solutions of H 2 PO 4 , H 2 SO 4 , HNO 3 , HClO 4 and HCl at different temperatures. The shape of the anodic charging curves depends on the electrolyte composition and on the temperature. The chemical composition of the films is strongly influenced by the working temperature. The first step of the anodization is the formation of a barrier film of amorphous WO 3 . The thickening of the oxide layer occurs on account of the WO 3 dissolution and following precipitation of sparingly soluble oxides on the electrode surface.