Search results for "testing."
showing 10 items of 1654 documents
In-process calibration of a non-destructive testing system used for in-process inspection of multi-pass welding
2020
Abstract In multi-pass welding, there is increasing motivation to move towards in-process defect detection to enable real-time repair; thus avoiding deposition of more layers over a defective weld pass. All defect detection techniques require a consistent and repeatable approach to calibration to ensure that measured defect sizing is accurate. Conventional approaches to calibration employ fixed test blocks with known defect sizes, however, this methodology can lead to incorrect sizing when considering complex geometries, materials with challenging microstructure, and the significant thermal gradients present in materials during the inter-pass inspection period. To circumvent these challenge…
Friction and wear testing of multilayer coatings on carbide substrates for dry machining applications
2002
Abstract The principle aim of this paper is to investigate three wear-protective coatings with multilayer structures, which are frequently used in the cutting tool industry and to assess their frictional behaviour under the test conditions equivalent to those for the cutting of medium carbon steel. A modified pin-on-disc tester was used to conduct experiments in which both the friction coefficient and the linear wear of the tribo-pair were recorded vs. sliding distance. The volumetric wear rate was proposed as a parameter for quantitative comparison of the wear resistance of the tribo-pairs tested. It was found that the principle stage of the specimen wear takes place during the first 200–2…
Fatigue crack initiation and subsequent crack growth in fillet welded steel joints
2019
Abstract The fatigue damage evolution in fillet welded steel joints where cracks are emanating from the weld toe is investigated. Based on existing experimental data for as-welded joints including crack depth measurements of the early crack growth it is proposed to make a distinction between the crack initiation phase and the subsequent crack growth phase. The welded detail in question is an F class detail with plate thickness 25 mm made of medium strength carbon steel. It is found that the crack initiation phase defined at a crack depth of 0.1 mm is close to 25% of the fatigue life even at a relatively high constant stress range of 150 MPa. At lower stress ranges it is concluded that the i…
Induced Modification of Flexural Toughness of Natural Hydraulic Lime Based Mortars by Addition of Giant Reed Fibers
2020
Abstract Nowadays, there is a growing need to reduce the environmental impact generated by the use of inorganic materials for building applications. The aim of this work is to investigate the bio-lime based mortar flexural toughness improvement due to the addition of common reed fibers (Arundo donax L.) in order to evaluate their possible application as ductile eco-compatible prefabricated bricks or laying and joint mortars for masonry. Different sets of specimens were tested by varying the fiber weight content and the fiber length. Moreover, chemical treatments with Linseed Oil and Polyethylene glycol (PEG) were performed to improve the physical and mechanical properties of the fibers as w…
Masonry columns confined with fabric reinforced cementitious matrix (FRCM) systems: A round robin test
2021
Abstract The conservation and the preservation of existing masonry buildings, most of them recognized as cultural heritage, require retrofitting techniques that should reduce the invasiveness and assure reversibility and compatibility with the substrate. In this perspective, the strengthening system should be able to improve the bearing capacity of the structural member and, at the same time, to assure mechanical and material compatibility. The use of Fabric Reinforced Cementitious Matrix (FRCM) composites is now recognized to be suitable for these purposes. Indeed, the inorganic matrix has comparable properties with respect to the existing historical mortars while the fabric has relevant t…
Scaffolds based on hyaluronan crosslinked with a polyaminoacid: Novel candidates for tissue engineering application
2008
New porous scaffolds, with a suitable hydrolytic and enzymatic degradation, useful for tissue engineering applications have been obtained by a carbodiimide mediated reaction between hyaluronan (HA) and a synthetic polymer with a polyaminoacid structure such as α,β-polyaspartylhydrazide (PAHy). Scaffolds with a different molar ratio between PAHy repeating units and HA repeating units have been prepared and characterized from a chemical and physicochemical point of view. Tests of indirect and direct cytotoxicity, cell adhesion, and spreading on these biomaterials have been performed by using murine L929 fibroblasts. The new biomaterials showed a good cell compatibility and ability to allow ce…
Effect of water contamination on the shear bond strength of five orthodontic adhesives
2010
Objectives: To evaluate the shear bond strength and site of failure of brackets bonded to dry and wet enamel. Study design: 50 teeth were divided into ten groups of 5 teeth each (10 surfaces). In half the groups enamel was kept dry before bonding, and in the other half distilled water was applied to wet the surface after etching. The following groups were established: 1)Acid/Transbond-XT (dry/wet) XT; 2) Transbond Plus Self Etching Primer (TSEP)/Transbond-XT paste (dry/wet); 3) Concise (dry), Transbond MIP/Concise (wet), 4) FujiOrtho-LC (dry/ wet); 5) SmartBond (dry/wet). Brackets were bonded to both buccal and lingual surfaces. Specimens were stored in distilled water (24 hours at 37ºC) an…
The Use of Atomic Force Microscopy in Determining the Stiffness and Adhesion Force of Human Dentin After Exposure to Bleaching Agents
2009
Introduction: Oxidant bleaching agents may induce several alterations on mineralized teeth tissues. Our aim is to study,at the ultrastructurallevel,mechanicalmodifications induced on dentin after exposure to different bleaching agents.Methods: Nanoindentation performed with atomic force microscopy was used to measure changes in dentin stiffness as well as the adhesion force between the tip and the tissue both in intertubular and peritubulardentin.Foreachspecimen,dentinlocalization, and bleaching agent, 100 independent nanoindentations were performed. Carbamide peroxide (30%) and hydrogenperoxide(35%) wereusedasbleaching agents. Results: A significant reduction of both stiffness and adhesion…
Casein phosphopeptide-amorphous calcium phosphate effects on brackets shear bond strength and enamel damage
2017
Background The aim of study was to evaluate the application of casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) and fluoride regarding their effect on the shear bond strength (SBS), bond failure pattern of brackets using the adhesive remnant index (ARI) and assessing the quality of enamel surface using the enamel damage index (EDI). Material and methods Sixty extracted premolar teeth were randomly divided into four groups regarding pretreatment application of CPP-ACP and fluoride. Brackets were bonded using the conventional method. Specimens were thermocycled for 1000 cycles and were subsequently tested for the SBS in a universal testing machine. After debonding, the teeth were e…
Spray-Drying, Solvent-Casting and Freeze-Drying Techniques: a Comparative Study on their Suitability for the Enhancement of Drug Dissolution Rates.
2019
Purpose Solid dispersions (SDs) represent the most common formulation technique used to increase the dissolution rate of a drug. In this work, the three most common methods used to prepare SDs, namely spray-drying, solvent-casting and freezedrying, have been compared in order to investigate their effect on increasing drug dissolution rate. Methods Three formulation strategies were used to prepare a polymer mixture of polyvinyl-alcohol (PVA) and maltodextrin (MDX) as SDs loaded with the following three model drugs, all of which possess a poor solubility: Olanzapine, Dexamethasone, and Triamcinolone acetonide. The SDs obtained were analysed and compared in terms of drug particle size, drug-lo…