Search results for "Applied Physics"
showing 10 items of 1226 documents
Modelling nanoparticles formation in the plasma plume induced by nanosecond pulsed lasers
2012
International audience; Nanoparticles formation in a laser-induced plasma plume in the ambient air has been investigated by using numerical simulations and physical models. For high irradiances, or for ultrashort laser pulses, nanoparticles are formed by condensation, as fine powders, in the expanding plasma for very high pairs of temperature and pressure. At lower irradiances, or nanosecond laser pulses, another thermodynamic paths are possible, which cross the liquid-gas transition curve while laser is still heating the target and the induced plasma. In this work, we explore the growth of nanoparticles in the plasma plume induced by nanosecond pulsed lasers as a function of the laser irra…
Influence of the tip effect of a carbon nanostructure on low current electrical arc initiation
2009
During their setting off, circuit breakers and vacuum switch devices are accompanied by an electric arc whose physical and chemical properties are governed by emissive current sites at the cathode surface called cathode spots. Assuming the continuity of the current on the cathode surfaces, the cathode spots contribute to supply the electrical arc by electron emission and material ejection. Thus they cause erosion on the contact electrodes inducing a dysfunction of contactors. The apparition of these cathode spots is due essentially to dust particles and surface irregularities at different scales. This experimental work represents a contribution to the understanding of the electrical arc beh…
The structural properties of GaN/AlN core-shell nanocolumn heterostructures.
2010
International audience; The growth and structural properties of GaN/AlN core-shell nanowire heterostructures have been studied using a combination of resonant x-ray diffraction, Raman spectroscopy and high resolution transmission electron microscopy experiments. For a GaN core of 20 nm diameter on average surrounded by a homogeneous AlN shell, the built-in strain in GaN is found to agree with theoretical calculations performed using a valence force field model. It is then concluded that for an AlN thickness up to at least 12 nm both core and shell are in elastic equilibrium. However, in the case of an inhomogeneous growth of the AlN shell caused by the presence of steps on the sides of the …
Detection and characterisation of disbonds on Fibre Metal Laminate hybrid composites by flying laser spot thermography
2017
Abstract In this work a novel data collection and processing is proposed for the Infrared Non-Destructive Testing (IR-NDT) of interlaminar disbonds on Fibre Metal Laminate (FML) hybrid composites. The adopted active IR-NDT scheme uses a pointwise laser heat source that is moved along a raster scanning trajectory over the object surface. A Focal Plane Array IR camera is employed to acquire the thermal field generated by the moving heat source. Disbonds defect signatures are then searched by analysing the perturbations of the temperature distribution over a reference area following the heat source. The proposed methodology has been implemented on a GLARE sample, since this class of FMLs has g…
A Numerical Study on Interlaminar Defects Characterization in Fibre Metal Laminates with Flying Laser Spot Thermography
2018
This work describes a numerical study on non-destructive evaluation of interlayer disbond defects in aerospace grade Fibre Metal Laminate sheets (FMLs). A recently proposed infrared non-destructive testing setup is considered, where a continuous laser is moved over the material surface, while the thermal footprint of the moving heat source is acquired, e.g. by an infrared thermal camera. Interlayer disbonds are then detected by analysing the features of the acquired thermograms. The experimental feasibility of this approach has been recently proved. The present work proposes a numerical simulation of the NDT approach, where the material thermal response is analysed and correlated to defects…
Phased laser diode array permits selective excitation of ultrasonic guided waves in coated bone-mimicking tubes
2017
This paper validates simulation predictions, which state that specific modes could be enhanced in quantitative ultrasonic bone testing. Tunable selection of ultrasonic guided wave excitation is useful in non-destructive testing since it permits the mediation of energy into diagnostically useful modes while reducing the energy mediated into disturbing contributions. For instance, it is often challenging to distinguish and extract the useful modes from ultrasound signals measured in bone covered by a soft tissue. We show that a laser diode array can selectively excite ultrasound in bone mimicking phantoms. A fiber-coupled diode array (4 elements) illuminated two solid tubes (2-3mm wall thickn…
Gd 3+ -doped sol-gel silica glass for remote ionizing radiation dosimetry
2019
Gadolinium-doped silica glass was prepared, using the sol-gel route, for ionizing radiation dosimetry applications. Such a glassy rod was drawn to a cane at a temperature of 2000 °C. The structural and optical properties of the obtained material were studied using Raman, optical absorption, and photoluminescence spectroscopies. Thereafter, a small piece of this Gd-doped scintillating cane was spliced to a transport passive optical fiber, allowing the remote monitoring of the X-ray dose rate through a radioluminescence (RL) signal. The sample exhibited a linear RL intensity response versus the dose rate from 125 µGy(SiO2)/s up to 12.25 Gy/s. These results confirm the potentialities of this m…
Corrosion Protection of Steel with Oxide Nanolaminates Grown by Atomic Layer Deposition
2011
Atomic layer deposited (ALD) aluminum and tantalum oxide (Al 2 O 3 and Ta 2 O 5 ) and their nanolaminates were applied as corrosion protection coatings on AISI 52100 steel. The aim was to combine the good sealing properties of Al 2 O 3 with the chemical stability of Ta 2 O 5 and to optimize the coating architecture in order to obtain the best possible long-term durability. Coating composition and morphology were studied with time-of-flight elastic recoil detection analysis (ToF-ERDA), time-of-flight secondary ion mass spectrometry (ToF-SIMS) and field emission scanning electron microscopy (FESEM) and energy dispersive x-ray spectrometry (EDS). Electrochemical properties were studied with vo…
Resistive switching in microscale anodic titanium dioxide-based memristors
2018
Licence CC BY-NC-ND The potentiality of anodic TiO2 as an oxide material for the realization of resistive switching memory cells has been explored in this paper. Cu/anodic-TiO2/Ti memristors of different sizes, ranging from 1 × 1 μm2 to 10 × 10 μm2 have been fabricated and characterized. The oxide films were grown by anodizing Ti films, using three different process conditions. Measured IV curves have shown similar asymmetric bipolar hysteresis behaviors in all the tested devices, with a gradual switching from the high resistance state to the low resistance state and vice versa, and a R_OFF/R_ON ratio of 80 for the thickest oxide film devices.
Optical modeling of nickel-base alloys oxidized in pressurized water reactor
2012
International audience; The knowledge of the aging process involved in the primary water of pressurized water reactor entails investigating a mixed growth mechanism in the corrosion of nickel-base alloys. A mixed growth induces an anionic inner oxide and a cationic diffusion parallel to a dissolution-precipitation process forms the outer zone. The in situ monitoring of the oxidation kinetics requires the modeling of the oxide layer stratification with the full knowledge of the optical constants related to each component. Here, we report the dielectric constants of the alloys 600 and 690 measured by spectroscopic ellipsometry and fitted to a Drude-Lorentz model. A robust optical stratificati…