Search results for "Metallurgy"

Determination of impurity distributions in ingots of solar grade silicon by neutron activation analysis

2017

AbstractIn a series of crystallization experiments, the directional solidification of silicon was investigated as a low cost path for the production of silicon wafers for solar cells. Instrumental neutron activation analysis was employed to measure the influence of different crystallization parameters on the distribution of 3d-metal impurities of the produced ingots. A theoretical model describing the involved diffusion and segregation processes during the solidification and cooling of the ingots could be verified by the experimental results. By successive etching of the samples after the irradiation, it could be shown that a layer of at least 60 μm of the samples has to be removed to get r…

Determination of elastoplastic properties of TiO2 thin films deposited on dual phase stainless steel using nanoindentation tests

2010

International audience; In recent years, the extraction of mechanical behaviour of thin films by nanoindentation using sharp indenter geometry has been extensively studied. This work investigates the mechanical properties of TiO2 thin film (1 µm thickness) deposited by spin coating on dual phase Duplex stainless steel and glass substrates. Experiments are carried out with different sharp triangular pyramids (a Cube corner and a Berkovich indenter) using a commercial Nano Indenter® XP apparatus. The substrate effect has been counteracted and an inverse method proposed in literature for bulk material has been adapted to assess the elastoplastic parameters of the tested thin film directly from…

Optical properties and microstructure of 2.02-3.30 eV ZnCdO nanowires: effect of thermal annealing

2013

International audience; ZnCdO nanowires with up to 45% Cd are demonstrated showing room temperature photoluminescence (PL) down to 2.02 eV and a radiative efficiency similar to that of ZnO nanowires. Analysis of the microstructure in individual nanowires confirms the presence of a single wurtzite phase even at the highest Cd contents, with a homogeneous distribution of Cd both in the longitudinal and transverse directions. Thermal annealing at 550 C yields an overall improvement of the PL, which is blue-shifted as a result of the homogeneous decrease of Cd throughout the nanowire, but the single wurtzite structure is fully maintained.

Controlled thermal oxidation of nanostructured vanadium thin films

2016

Abstract Pure V thin films were dc sputtered with different pressures (0.4 and 0.6 Pa) and particle incident angles α of 0°, 20° and 85°, by using the GLancing Angle Deposition (GLAD) technique. The sputtered films were characterized regarding their electrical resistivity behaviour in atmospheric pressure and in-vacuum conditions as a function of temperature (40–550 °C), in order to control the oxidation process. Aiming at comprehending the oxidation behaviour of the samples, extensive morphological and structural studies were performed on the as-deposited and annealed samples. Main results show that, in opposition to annealing in air, the columnar nanostructures are preserved in vacuum con…

Atomic layer deposition of aluminum oxide on modified steel substrates

2016

Abstract Al 2 O 3 thin films were grown by atomic layer deposition to thicknesses ranging from 10 to 90 nm on flexible steel substrates at 300 °C using Al(CH 3 ) 3 and H 2 O as precursors. The films grown to thicknesses 9–90 nm covered the rough steel surfaces uniformly, allowing reliable evaluation of their dielectric permittivity and electrical current densities with appreciable contact yield. Mechanical behavior of the coatings was evaluated by nanoindentation. The maximum hardness values of the Al 2 O 3 films on steel reached 12 GPa and the elastic modulus exceeded 280 GPa.

Production of dense nanostructured materials using FAPAS and SPS techniques

2011

International audience

Influence of the MgO barrier thickness on the lifetime characteristics of magnetic tunnelling junctions for sensors

2016

Magnetic tunnelling junctions increasingly enter the market for magnetic sensor applications. Thus, technological parameters such as the lifetime characteristics become more and more important. Here, an analysis of the lifetime characteristics of magnetic tunnelling junctions using the Weibull statistical distribution for CoFeB/MgO/CoFeB junctions is presented. The Weibull distribution is governed by two parameters, the characteristic lifetime η of the population and the shape parameter β, which gives information about the presence of an infant mortality. The suitability of the Weibull distribution is demonstrated for the description of dielectric breakdown processes in MgO-based tunnelling…

Leaded Bronze: An Innovative Lead Substitute for Cathodic Electrosynthesis

2017

Strombolian eruptions and dynamics of magma degassing at Yasur Volcano (Vanuatu)

2020

Abstract Open vent basaltic volcanoes account for a substantial portion of the global atmospheric outgassing flux, largely through passive degassing and mild explosive activity. We present volcanic gas flux and composition data from Yasur Volcano, Vanuatu collected in July 2018. The average volcanic plume chemistry is characterised by a mean molar CO2/SO2 ratio of 2.14, H2O/SO2 of 148 and SO2/HCl of 1.02. The measured mean SO2 flux in the period of 6th to 9th July is 4.9 kg s−1. Therefore, the mean fluxes of the other species are 7.5 kg∙s−1 CO2, 208 kg∙s−1 H2O and 4.8 kg∙s−1 HCl. The degassing regime at Yasur volcano ranges from ‘passive’ to ‘active’ styles, with the latter including Stromb…

Changes in SO2 Flux Regime at Mt. Etna Captured by Automatically Processed Ultraviolet Camera Data

2019

We used a one-year long SO2 flux record, which was obtained using a novel algorithm for real-time automatic processing of ultraviolet (UV) camera data, to characterize changes in degassing dynamics at the Mt. Etna volcano in 2016. These SO2 flux records, when combined with independent thermal and seismic evidence, allowed for capturing switches in activity from paroxysmal explosive eruptions to quiescent degassing. We found SO2 fluxes 1.5−2 times higher than the 2016 average (1588 tons/day) during the Etna’s May 16−25 eruptive paroxysmal activity, and mild but detectable SO2 flux increases more than one month before its onset. The SO2 flux typically peaked during a lava fo…