Search results for "STING"

Boosting the supercapacitive behavior of CoAl-layered double hydroxides via tuning the metal composition and interlayer space

2020

Layered double hydroxides (LDHs) are promising supercapacitor materials due to their wide chemical versatility, earth abundant metals and high specific capacitances. Many parameters influencing the supercapacitive performance have been studied such as the chemical composition, the synthetic approaches, and the interlayer anion. However, no systematic studies about the effect of the basal space have been carried out. Here, two-dimensional (2D) CoAl-LDHs were synthesized through anion exchange reactions using surfactant molecules in order to increase the interlayer space (ranging from 7.5 to 32.0 Å). These compounds exhibit similar size and dimensions but different basal space to explore excl…

Boosting the Performance of One-Step Solution-Processed Perovskite Solar Cells Using a Natural Monoterpene Alcohol as a Green Solvent Additive

2021

The perovskite film is the core of a perovskite solar cell (PSC), and its quality is crucial for the performance of such devices. The morphology, crystallinity, and surface coverage of the perovskite layer greatly affect the power conversion efficiency (PCE), hysteresis, and long-term stability of PSCs. The incorporation of appropriate solvent additives in the perovskite precursor solution is an effective strategy to control the film morphology and reduce the defects and grain boundaries. However, the commonly used solvent additives are environmentally harmful and highly toxic. In this work, α-terpineol (a nontoxic, eco-friendly, and low-cost monoterpene alcohol) is employed for the first t…

In-process calibration of a non-destructive testing system used for in-process inspection of multi-pass welding

2020

Abstract In multi-pass welding, there is increasing motivation to move towards in-process defect detection to enable real-time repair; thus avoiding deposition of more layers over a defective weld pass. All defect detection techniques require a consistent and repeatable approach to calibration to ensure that measured defect sizing is accurate. Conventional approaches to calibration employ fixed test blocks with known defect sizes, however, this methodology can lead to incorrect sizing when considering complex geometries, materials with challenging microstructure, and the significant thermal gradients present in materials during the inter-pass inspection period. To circumvent these challenge…

Friction and wear testing of multilayer coatings on carbide substrates for dry machining applications

2002

Abstract The principle aim of this paper is to investigate three wear-protective coatings with multilayer structures, which are frequently used in the cutting tool industry and to assess their frictional behaviour under the test conditions equivalent to those for the cutting of medium carbon steel. A modified pin-on-disc tester was used to conduct experiments in which both the friction coefficient and the linear wear of the tribo-pair were recorded vs. sliding distance. The volumetric wear rate was proposed as a parameter for quantitative comparison of the wear resistance of the tribo-pairs tested. It was found that the principle stage of the specimen wear takes place during the first 200–2…

Fatigue crack initiation and subsequent crack growth in fillet welded steel joints

2019

Abstract The fatigue damage evolution in fillet welded steel joints where cracks are emanating from the weld toe is investigated. Based on existing experimental data for as-welded joints including crack depth measurements of the early crack growth it is proposed to make a distinction between the crack initiation phase and the subsequent crack growth phase. The welded detail in question is an F class detail with plate thickness 25 mm made of medium strength carbon steel. It is found that the crack initiation phase defined at a crack depth of 0.1 mm is close to 25% of the fatigue life even at a relatively high constant stress range of 150 MPa. At lower stress ranges it is concluded that the i…

LES investigation of heat and mass exchange in channel induction furnaces

2009

Induced Modification of Flexural Toughness of Natural Hydraulic Lime Based Mortars by Addition of Giant Reed Fibers

2020

Abstract Nowadays, there is a growing need to reduce the environmental impact generated by the use of inorganic materials for building applications. The aim of this work is to investigate the bio-lime based mortar flexural toughness improvement due to the addition of common reed fibers (Arundo donax L.) in order to evaluate their possible application as ductile eco-compatible prefabricated bricks or laying and joint mortars for masonry. Different sets of specimens were tested by varying the fiber weight content and the fiber length. Moreover, chemical treatments with Linseed Oil and Polyethylene glycol (PEG) were performed to improve the physical and mechanical properties of the fibers as w…

Masonry columns confined with fabric reinforced cementitious matrix (FRCM) systems: A round robin test

2021

Abstract The conservation and the preservation of existing masonry buildings, most of them recognized as cultural heritage, require retrofitting techniques that should reduce the invasiveness and assure reversibility and compatibility with the substrate. In this perspective, the strengthening system should be able to improve the bearing capacity of the structural member and, at the same time, to assure mechanical and material compatibility. The use of Fabric Reinforced Cementitious Matrix (FRCM) composites is now recognized to be suitable for these purposes. Indeed, the inorganic matrix has comparable properties with respect to the existing historical mortars while the fabric has relevant t…

Graphene Oxide Carboxymethylcellulose Nanocomposite for Dressing Materials.

2020

Sore, infected wounds are a major clinical issue, and there is thus an urgent need for novel biomaterials as multifunctional constituents for dressings. A set of biocomposites was prepared by solvent casting using different concentrations of carboxymethylcellulose (CMC) and exfoliated graphene oxide (Exf-GO) as a filler. Exf-GO was first obtained by the strong oxidation and exfoliation of graphite. The structural, morphological and mechanical properties of the composites (CMCx/Exf-GO) were evaluated, and the obtained composites were homogenous, transparent and brownish in color. The results confirmed that Exf-GO may be homogeneously dispersed in CMC. It was found that the composite has an i…

Scaffolds based on hyaluronan crosslinked with a polyaminoacid: Novel candidates for tissue engineering application

2008

New porous scaffolds, with a suitable hydrolytic and enzymatic degradation, useful for tissue engineering applications have been obtained by a carbodiimide mediated reaction between hyaluronan (HA) and a synthetic polymer with a polyaminoacid structure such as α,β-polyaspartylhydrazide (PAHy). Scaffolds with a different molar ratio between PAHy repeating units and HA repeating units have been prepared and characterized from a chemical and physicochemical point of view. Tests of indirect and direct cytotoxicity, cell adhesion, and spreading on these biomaterials have been performed by using murine L929 fibroblasts. The new biomaterials showed a good cell compatibility and ability to allow ce…