Search results for "Temperature measurement"
showing 10 items of 123 documents
Temperature measurements along a vertical borehole heat exchanger: A method comparison
2019
Abstract The standard thermal response tests (TRT) provide integral and effective thermal parameters of the ground in the vicinity of borehole heat exchangers (BHE). However, typical ground properties are heterogeneously distributed. As a result, advanced TRT such as distributed and enhanced TRT are growing in popularity as they provide more spatial information of the thermal properties. Thus, the objective of this study is to compare various instruments to measure the depth-dependent temperatures using standard Pt100-sensors, fiber optical thermometers and novel instruments such as Geowire, Geoball and GEOsniff®. The investigations are carried out in a 30 m length test borehole. The result…
Review of acoustic methods for space charge measurement
2015
In the last decade, due to the increased use of direct current, the space charge accumulation phenomenon has reached more interest. In this regard, several non-destructive measurement systems were used. In particular, for solid dielectrics, the acoustic methods have had greater success. This review presents a brief historical evolution of the Pulse Electro- Acoustic (PEA) method, describing the working operation, the thicknesses analyzed and the spatial resolution for the different configurations of the PEA cell. The Pressure Wave Propagation (PWP) method in both configurations Piezo-PWP and Laser Induced Pressure Pulse (LIPP) is also described.
Experimental Investigation of the Optimal Ingot Resistivity for both the Cell Performances and the Temperature Coefficients for Different Cell Archit…
2018
Compensation engineering enables the achievement of lower ingot resistivities with relatively constant performances along the ingot height. In this paper the impact of the bulk resistivity on the cell performances and the temperature coefficients is investigated for compensated and non-compensated multicrystalline silicon. Based on experimental data we show that reducing the bulk resistivity below a certain value improves the temperature coefficients but deteriorates the cell performances for two distinct cell architectures (AI-BSF and PERCT). Moreover this performance loss is not balanced out by the improved temperature coefficient for operating conditions below 70°C.
Improved Temperature Coefficient Modeling through the Recombination Parameter $\gamma$
2020
This study presents an injection dependent numerical model relating Shocldey-Read-Hall defect parameters in crystalline silicon with the recombination parameter $\gamma$ . We demonstrate how the model can be used to predict $\gamma$ for various single level defects. Additionally, we show that $\gamma$ can be significantly influenced by the injection level, in contrast to what is commonly assumed. The injection dependence is found to correlate with the temperature sensitivity of the Shocldey-Read-Hall lifetime. Finally, we demonstrate that the model can be used to predict the temperature coefficient of the open circuit voltage without the use of a temperature dependent measurement, enabling …
Initial light-induced degradation study of multicrystalline modules made from silicon material processed through different manufacturing routes
2012
The paper presents results of initial lightinduced degradation (LID) of multicrystalline silicon photovoltaic (PV) modules made of crystalline silicon from different manufacturing processes. The modules were installed within the Sunbelt, in Hyderabad, India. Current-voltage (I–V) characteristics are measured and infra-red (IR) images of the modules are taken at regular intervals. A relationship of the IV degradation with the IR images is discussed. Results from laboratory LID tests at room temperature are performed parallel to the outdoor degradation of PV modules. It was found that the total LID, measured on the module level, after the initial 40 hours is similar for both materials resulti…
Temperature Measurements as a Method for Monitoring Ropes
2020
Due to an increasing demand for operation at sea depths as low as 3000 m and under, the use of fibre ropes for offshore application in deep sea lifting and mooring is increasing. Consequently, improved knowledge is required regarding these ropes’ thermo-mechanical properties and how these properties change as the rope is being used. This paper presents a 2D model of heat transport in the axial and radial directions along a 28 mm diameter fibre rope typically used for offshore applications. The model is combined with temperature measurements during heating and cooling of the rope, using both thermocouples and a thermal camera. Measurements are performed both on a new rope and on a used that …
New Results on High-Resolution 3-D CZT Drift Strip Detectors
2020
Intense research activities have been carry out in the development of room temperature gamma ray spectroscopic imagers, aiming to compete with the excellent energy resolution of high-purity germanium (HPGe) detectors (0.3 % FWHM at 662 keV) obtained after cryogenic cooling. Cadmium-zinc-telluride (CZT) detectors equipped with pixel, strip and virtual Frisch-grid electrode structures represented an appealing solution for room temperature measurements. In this work, we present the performance of new high-resolution CZT drift strip detectors (19.4 x 19.4 x 6 mm3), recently fabricated at IMEM-CNR of Parma (Italy) in collaboration with due2lab company (Reggio Emilia, Italy). The detectors, worki…
Improvement of building wall surface temperature measurements by infrared thermography
2005
By using quantitative thermal scanning of building surface structures, it is possible to access the temperature field. For further calculation of the heat flux exchanged by these structures with the environment, one must quantify as finely as possible the temperature field on the bodies surfaces. For this purpose we have to take into account that real bodies are not black, which implies that a part of the ambient radiation received by the infrared camera detectors is reflected radiation. In this paper, we present a method to quantify the reflected flux by using an infrared mirror, which allows large surface temperature measurements by infrared thermography under near-ambient conditions with…
A magnetostrictive sensor interrogated by fiber gratings for DC-current and temperature discrimination
2000
A magnetostrictive sensor head with temperature compensation has been developed for measurement of static magnetic fields. The device consists on two different alloys with similar thermal expansion coefficient one of which has a giant magnetostriction, the expansion of both materials produced by heat and magnetism is detected by two fiber gratings. One of the gratings measures the temperature of the sensor and the difference between the wavelengths reflected by the gratings is a measurement of the magnetically induced strain.
High Temperature SiC Blocking Diodes for Solar Array
2009
This paper presents the results of an experimental investigation of the performance of 300V-5A Silicon Carbide Ni and W Schottky diode operating in the range between -170°C to 270°C. We have developed these diodes as blocking diodes, for solar cell array protection in order to fulfill the BepiColombo mission specifications. An electro-thermal characterization has been performed taking into account the harsh condition of the mission (high temperature range and electrical stress). The destructive and non-destructive tests have assured that the designed SiC diodes are able to support the electro-thermal limits. A reliability test has also been performed to investigate the stability of forward …