Search results for "Toe"
showing 10 items of 3824 documents
Measurements of thickness dispersion in biolayers by scanning force microscopy and comparison with spectroscopic ellipsometry analysis.
2007
Measuring the thickness of biological films remains a difficult task when using differential measurements by atomic force microscopy (AFM). The use of microstructured substrates combined with a selective adsorption constitutes an alternative to tribological measurements. The statistical thickness analysis of biological layers, especially via the dispersion measurements, can provide a way to quantify the molecular orientation. AFM thicknesses were then compared with those obtained optically by spectroscopic ellipsometry (SE) and surface plasmon resonance enhanced ellipsometry (SPREE). The biolayers could then be modeled using a vertical gradient of optical index, which reflects height disper…
Room-Temperature Cubic Phase Crystallization and High Stability of Vacuum-Deposited Methylammonium Lead Triiodide Thin Films for High-Efficiency Sola…
2019
Methylammonium lead triiodide (MAPI) has emerged as a high-performance photovoltaic material. Common understanding is that at room temperature it adopts a tetragonal phase and it only converts to the perfect cubic phase around 50-60 ºC. Most MAPI films are prepared using a solution-based coating process, yet they can also be obtained by vapor phase deposition methods. Vapor phase processed MAPI films have significantly different characteristics compared to their solvent processed analogous, such as a relatively small crystal grain sizes and short excited state lifetimes. Yet solar cells based on vapor phase processed MAPI films exhibit high power conversion efficiencies. Surprisingly, after…
Benzene monitoring by micro-machined sensors with SnO2 layer obtained by using micro-droplet deposition technique
2011
International audience; SnO2 thin layers were deposited by the way of the micro-droplet technique. The sensor substrate consisted of a thin membrane developed on oxidised silicon wafer. The sensing layers were deposited by means of the micro-droplet technique into thin layers of about 100 nm. Such devices were tested for benzene detection. The obtained results showed a very high sensitivity for this chemical compound since 500 ppb were detected. The results presented in this paper were not focused on the reactional mechanism of benzene detection but rather on the development of a cheap and sensitive sensor using sol-gel and micro-droplet processes. Since these layers were elaborated using s…
Current rectification in a single molecule diode: the role of electrode coupling.
2015
We demonstrate large rectification ratios (> 100) in single-molecule junctions based on a metal-oxide cluster (polyoxometalate), using a scanning tunneling microscope (STM) both at ambient conditions and at low temperature. These rectification ratios are the largest ever observed in a single-molecule junction, and in addition these junctions sustain current densities larger than 10^5 A/cm^2. By following the variation of the I-V characteristics with tip-molecule separation we demonstrate unambiguously that rectification is due to asymmetric coupling to the electrodes of a molecule with an asymmetric level structure. This mechanism can be implemented in other type of molecular junctions u…
Thin film growth and band lineup of In2O3 on the layered semiconductor InSe
1999
Thin films of the transparent conducting oxide In2O3 have been prepared in ultrahigh vacuum by reactive evaporation of indium. X-ray diffraction, optical, and electrical measurements were used to characterize properties of films deposited on transparent insulating mica substrates under variation of the oxygen pressure. Photoelectron spectroscopy was used to investigate in situ the interface formation between In2O3 and the layered semiconductor InSe. For thick In2O3 films a work function of φ = 4.3 eV and a surface Fermi level position of EF−EV = 3.0 eV is determined, giving an ionization potential IP = 7.3 eV and an electron affinity χ = 3.7 eV. The interface exhibits a type I band alignmen…
XPS analysis of sol-gel-generated mixed-oxide layers for biomedical application
2002
The excellent biocompatibility of titanium and its alloys is associated with the properties of their dense TiO2 layer on the surface. The adsorption of proteins of the body fluid to implant surfaces depends on the properties of the surface oxide layer, especially the electronic structure. Therefore, tailoring of the oxide layer is a method for influencing protein adsorption. In this study, titanium platelets are coated by the sol–gel process with mixed oxides containing the biocompatible elements Ti, Nb, Zr and Ta. In order to verify the composition of the produced oxide layer, which can differ from the adjusted precursor composition in the sol because of different reactivities of the precu…
Investigations of the corrosion protection of ultrathin a-C and a-C:N overcoats for magnetic storage devices
2004
Abstract The thickness-dependent corrosion protection of carbon overcoats for magnetic hard disks can be analyzed by collecting X-ray absorption near edge structure (XANES) spectra at the Co L3-edge. Co is the main constituent of the protected magnetic media underneath. The spectra of the Co absorption edge display a strong peak for pure metallic, non-oxidized Co. This peak splits up into several sub-structures for oxidized Co. Therefore, XANES spectra provide a straightforward method to determine the overcoat thickness, leading to closed coverage and corrosion protection of the underlying material. A similar approach was carried out by X-ray photoelectron spectroscopy (XPS). Standard a-C:N…
Structural and electrical properties of cerium tungstate: Application to methane conversion
2020
International audience; The catalytic efficiency as well as the electrical conduction mechanism of Ce2(WO4)3 powders synthetized for the oxidation of methane were investigated. Total and partial oxidation reactions were observed in the temperature range between 600 and 750 °C under CH4/dry air flux, for low CH4 concentrations. The electrical conduction mechanism is based on electron tunneling at low temperature (< 650 °C) and hopping over an ion barrier at high temperature, which favors the catalytic oxidation of CH4 in air; these mechanisms occur during the partial and total oxidation under weak gas flow. The occurrence of these types of conduction mechanism was related both to the distort…
Temperature and substrate influence on the structure of TiN O thin films grown by low pressure metal organic chemical vapour deposition
2000
Abstract This paper presents the growth and characterization of titanium oxinitride (TiN x O y ) films grown by low pressure metal organic chemical vapour deposition (LP-MOCVD). The film nitrogen content, obtained by Rutherford backscattering spectroscopy (RBS), increases as the growth temperature increases (from 23 at.% at 450°C to 46 at.% at 750°C). Below 550°C, the films do not show any X-ray diffraction pattern. Above 550°C, the deposited films present the (111) and (200) TiN textures. Films deposited on (100) Si exhibit a 2 θ shift to higher Bragg angles, depending on the N/O ratio. These shifts are explained by using a substitutional oxygen model. Moreover, the atomic structure of suc…
Zinc oxide nanocrystals as electron injecting building blocks for plastic light sources
2012
Hybrid inorganic–organic light emitting devices (HyLEDs) employing ZnO nanocrystals as one of their metal oxide contacts lead to very bright devices on plastic substrates with performances superior to those obtained from the rigid counterparts employing planar films of bulk ZnO. The superior performance is related to the increase in the bandgap of the ZnO nanocrystals caused by quantum confinement effects. We demonstrate that this effect diminishes with increasing annealing temperature of the ZnO nanocrystal layer due to a gradual decrease of the bandgap towards the bulk ZnO value. Therefore, best performances were obtained with room temperature processing of the ZnO nanocrystals.