Search results for "Volt"
showing 10 items of 2187 documents
Fabrication and characterization of small tunnel junctions through a thin dielectric membrane
1998
We show that a small tapered hole through a thin silicon nitride membrane provides a mask for tunnel junction structures. Our experiments imply, unlike in the conventional planar electron beam lithography, that tunnel junctions are well voltage biased in this structure with vanishingly small on-chip impedance. Our technique allows fabrication of double junctions, and even multijunction linear arrays, with small metallic islands in between.
Fabrication and Characterisation of Perovskite Thin Films for Photovoltaic Application
2018
This paper presents an alternative way to obtain perovskite thin films for photovoltaic application. This technique results more competitive, scalable, low-cost, reproducible and is different from other most common methods of fabrication.
Corrosion resistance of passive films on different stainless steel grades in food and beverage industry
2020
Abstract Passive films were grown on 304 L, 316 L and Duplex stainless steels by immersion at open circuit potential in solutions mimicking food and beverage industry environments. In acidic food stainless steel surfaces are covered by Cr rich passive films, and generalized dissolution occurs on their surface with consequent ions release into the electrolyte. In fatty food the concentration of released ions is significantly lower since generalized corrosion does not occur, but the loss on MnS inclusions strongly reduces the polarization resistance in this environment especially for 304 L due to its higher localized corrosion susceptibility with respect to the other grades.
Fullerene imposed high open-circuit voltage in efficient perovskite based solar cells
2016
Five different commercially available fullerenes are evaluated as hole blocking/electron transporting materials in p–i–n methylammonium lead iodide perovskite solar cells using a vacuum deposited perovskite absorber layer. A significant enhancement of the solar cell performance can be obtained by selecting a suitable fullerene derivative. Open-circuit voltages as high as 1.11 volts are obtained leading to a power conversion efficiency of 14.6%.
New concepts and applications in macromolecular chemistry of fullerenes
2010
A new classification on the different types of fullerene-containing polymers is presented according to their different properties and applications they exhibit in a variety of fields. Because of their interest and novelty, water-soluble and biodegradable C(60)-polymers are discussed first, followed by polyfullerene-based membranes where unprecedented supramolecular structures are presented. Next are compounds that involve hybrid materials formed from fullerenes and other components such as silica, DNA, and carbon nanotubes (CNTs) where the most recent advances have been achieved. A most relevant topic is still that of C(60)-based donor-acceptor (D-A) polymers. Since their application in pho…
Meniscus coated high open-circuit voltage bi-layer solar cells
2012
Neat bi-layer solar cells of a fullerene acceptor and a cyanine dye donor were prepared using meniscus coating. Meniscus coating is very material efficient and leads to high quality pinhole-free films. The cells exhibit high open circuit voltages of 1 volt, only 0.8 eV below the band gap of the cyanine dye. This is one of the smallest differences reported for organic solar cells and illustrates an almost optimal donor-acceptor energy level alignment.
Influence of the intermediate density-of-states occupancy on open-circuit voltage of bulk heterojunction solar cells with different fullerene accepto…
2010
Electron density of states (DOS) and recombination kinetics of bulk heterojunction solar cells consisting of a poly(3-hexylthiophene) (P3HT) donor and two fullerene acceptors, either [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) or 4,4′-dihexyloxydiphenylmethano[60]fullerene (DPM6), have been determined by means of impedance spectroscopy. The observed difference of 125 mV in the output open-circuit voltage is attributed to significant differences of the occupancy of the DOS in both fullerenes. Whereas DPM6 exhibits a full occupation of the electronic band, occupancy is restricted to the tail of the DOS in the case of PCBM-based devices, implying a higher rise of the Fermi level in the D…
Bending Sensors Based on Thin Films of Semitransparent Bithiophene-Fulleropyrrolidine Bisadducts
2020
In this study, a novel bithiophene‐fulleropyrrolidine bisadducts system (bis‐Th2PC 60 ) was synthesized and electropolymerized by chronoamperometry onto flexible ITO/PET substrates. The resulting semitransparent thin film was characterized by XPS, FT‐IR, cyclic voltammetry and optical techniques, confirming the good outcome of the electropolymerization process. AFM investigations permitted to highlight an inherent disordered granular morphology, in which the grain‐to‐grain separation depends upon the application of bending. The electrical resistance of the thin film was characterized as function of bending (in the range 0°‐90°), showing promising responsivity to low bending angles (10°‐30°)…
Discrimination of papers used in conservation and restoration by the means of the voltammetry of immobilized microparticles technique
2019
Herein, voltammetry of immobilized microparticles (VIMP) is employed for the discrimination of papers used in the conservation and restoration field. The electrochemical parameters are used for the discrimination of different samples coming from China, Japan and Korea. The method is based on the recording of the voltammetric response of microparticulate deposits from acetone extracts of paper samples deposited on a glassy carbon electrode in contact with 1.0 M H2SO4. The voltammetric responses attributed to the lignin and the oxidation products of the cellulose were collected and are discussed. The grouping of samples was obtained upon the application of the chemometric methods, as well as …
In-situ electrochemical atomic force microscopy study of aging of magnetron sputtered Pt-Co nanoalloy thin films during accelerated degradation test
2016
Abstract A Pt-Co nanoalloy thin film catalyst was prepared by using simultaneous magnetron sputtering of Pt and Co. The catalyst was characterized during accelerated degradation test using in-situ electrochemical atomic force microscopy complemented with ex-situ techniques such as energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy and synchrotron radiation photoelectron spectroscopy. The combined results gave the full step-by-step picture of the catalyst behavior during the aging test.