Effect of extended famine conditions on aerobic granular sludge stability in the treatment of brewery wastewater

2017

Results obtained from three aerobic granular sludge reactors treating brewery wastewater are presented. Reactors were operated for 60 d days in each of the two periods under different cycle duration: (Period I) short 6 h cycle, and (Period II) long 12 h cycle. Organic loading rates (OLR) varying from 0.7 kg COD m-3 d-1 to 4.1 kg COD m-3 d-1 were tested. During Period I, granules successfully developed in all reactors, however, results revealed that the feast and famine periods were not balanced and the granular structure deteriorated and became irregular. During Period II at decreased 12 h cycle time, granules were observed to develop again with superior structural stability compared to the…

Membrane Fouling Mitigation in MBR via the Feast–Famine Strategy to Enhance PHA Production by Activated Sludge

2022

Fouling is considered one of the main drawbacks of membrane bioreactor (MBR) technology. Among the main fouling agents, extracellular polymeric substances (EPS) are considered one of the most impactful since they cause the decrease of sludge filterability and decline of membrane flux in the long term. The present study investigated a biological strategy to reduce the membrane-fouling tendency in MBR systems. This consisted of seeding the reactor with activated sludge enriched in microorganisms with polyhydroxyalkanoate (PHA) storage ability and by imposing proper operating conditions to drive the carbon toward intracellular (PHA) rather than extracellular (EPS) accumulation. For that purpos…

Quantification of kinetic parameters for heterotrophic bacteria via respirometry in a hybrid reactor

2010

Over the last decade new technologies are emerging even more for wastewater treatment. Among the new technologies, a recent possible solution regards Moving Bed Biofilm Reactors (MBBRs) that represent an effective alternative to conventional processes. More specifically such systems consist in the introduction of plastic elements inside the aerobic reactor as carrier material for the growth of attached biomass. Recently, one of the mostly used alternatives is to couple the Moving Bed Biofilm Reactor (MBBR) process with the conventional activated sludge process, and the resulting process is usually called HMBBR (Hybrid MBBR). In the MBBR process the biofilm grows attached on small plastic el…

The role of fouling mechanisms in a submerged membrane bioreactor during the start-up

2006

Wastewater modification processes assessment in a stabilization reservoir.

2008

A semi-empirical mechanistic model able to simulate the dynamics of a stabilization reservoir was developed incorporating both settling of particulate components and chemical/biological processes. Several factors affecting the reservoir effluent quality were taken into account: hydraulics and hydrology, solar radiation, atmospheric reaeration, algae, zooplankton, organic matter, pathogen bacteria, and sediment-water interaction. The model quantifies the specific influence of each factor on effluent quality, evaluating the correlation between the different considered factors. State variables included in the model were: algae, dissolved oxygen, organic matter, zooplankton and indicator bacter…

Challenges and opportunities for citrus wastewater management and valorisation: A review.

2022

Citrus wastewaters (CWWs) are by-products of the citrus fruit transformation process. Currently, more than 700 million of m³ of CWWs per year are produced worldwide. Until nowadays, the management of CWWs is based on a take-make-use-dispose model. Indeed, after being produced within a citrus processing industry, CWWs are subjected to treatment and then discharged into the environment. Now, the European Union is pushing towards a take-make-use-reuse management model, which suggests to provide for the minimization of residual pollutants simultaneously with their exploitation through a biorefinery concept. Indeed, the recovery of energy nutrients and other value-added products held by CWWs may…

Foaming estimation tests in activated sludge systems.

2005

Persistent biological foaming phenomena in activated sludge systems due to excess of filamentous microorganisms with hydrophobic properties, such as GALO, Microthrix parvicella and others, are frequently reported everywhere. Nevertheless, even if the number of plants affected by this trouble is high, presently there are no suitable general methods to evaluate properly the phenomenon. This paper reports on the results of a series of foam tests (Scum Index, Foam Rating), of hydrophobicity measurements of activated sludge (mixed liquor and foam) and measurements of extension of aeration tank covered by foam surfaces. The data obtained by using the above indicated methods are clearly correlated…

Effect of biomass features on oxygen transfer in conventional activated sludge and membrane bioreactor systems

2019

Abstract The aim of the present study was to compare the oxygen transfer efficiency in a conventional activated sludge and a membrane bioreactor system. The oxygen transfer was evaluated by means of the oxygen transfer coefficient and α-factor calculation, under different total suspended solids concentration, extracellular polymeric substances, sludge apparent viscosity and size of the flocs. The oxygen transfer coefficient and α-factor showed an exponential decreasing trend with total suspended solid, with a stronger oxygen transfer coefficient dependence in the conventional activated sludge compared to the membrane bioreactor. It was noted that the oxygen transfer coefficient in the conve…

Pilot scale experiment with MBR operated in intermittent aeration condition: analysis of biological performance.

2014

The effect of intermittent aeration (IA) on a MBR system was investigated. The study was aimed at ana- lyzing different working conditions and the influence of different IA cycles on the biological performance of the MBR pilot plant, in terms of organic carbon and ammonium removal as well as extracellular poly- meric substances (EPSs) production. The membrane modules were placed in a separate compartment, continuously aerated. This configuration allowed to disconnect from the filtration stage the biological phenomena occurring into the IA bioreactor. The observed results highlighted good efficiencies, in terms of organic carbon and ammonium removal. It was noticed a significant soluble micr…

The role of fouling mechanisms in a membrane bioreactor.

2007

The present study has aimed to quantify the role of pore blocking and cake layer in a laboratory scale hollow fibre membrane module in submerged configuration. The membrane reactor (MBR) was fed with raw wastewater, only screened with a 2-mm sieve, collected from the Palermo WWTP. The MBR was characterised by an operating volume of 190 L and equipped with an aeration system located on the bottom of the reactor. The MBR operated for 65 days. The permeate was extracted by imposing a constant flux through the membrane (21 Lh−1m−2). The results confirm the importance of pore blocking control during start-up. In particular, it provides a rapid irreversible fouling that takes place at the beginni…

Suspended and attached biomass in an mbr system treating high strength wastewater Loads

2012

abstract

Respirometry for the Characterization of Heterotrophic Biomass Activity: Application to a MBR Pilot Plant Operated with Two Different Start-Up Strate…

2016

A membrane bioreactor (MBR) pilot plant was operated in two subsequent experimental periods (namely, Periods I and II) with different start-up and sludge withdrawal strategies to study its peculiar biokinetic behavior by using respirometric techniques. Two extreme operational conditions were chosen to investigate the different biomass activity under dynamic or pseudostationary conditions during and after the start-up phases. Particularly, the MBR pilot plant was operated with the same volumetric loading rate (VLR) and permeate flux but differently managed during the start-up phase. In Period I, the MBR pilot plant was started up without sludge inoculum and operated without sludge withdrawal…

Biopolymer Recovery from Aerobic Granular Sludge and Conventional Flocculent Sludge in Treating Industrial Wastewater: Preliminary Analysis of Differ…

2022

The recovery of biopolymers from sewage sludge could be a crucial step in implementing circular economy principles in wastewater treatment plants (WWTP). In this frame, the present study was aimed at evaluating the simultaneous production of polyhydroxyalkanoates (PHA) and extracellular polymeric substances (EPS) obtainable from the treatment of agro-industrial wastewater. Two biological enrichment systems, aerobic granular sludge (AGS) and a conventional activated sludge operating as a sequencing batch reactor (SBR), were monitored for 204 and 186 days, respectively. The maximum biopolymers accumulation capacity was close to 0.60 mgPHA-EPS gVSS−1 in the AGS when operating at 3 kgCODm…

The role of EPS in fouling and foaming phenomena for a membrane bioreactor

2013

In contraposition to conventional activated sludge processes, the foaming phenomenon in membrane bioreactor (MBR) is still in its infancy. On the other hand, although several studies have been carried out for better understanding the fouling phenomenon in MBR there are still some gaps in the up-to-date knowledge. The extracellular polymeric substances (EPSs) may have a primary role in fouling and foaming phenomena which in turn can be crucial for MBRs. The aim of this study is to detect a possible relationship that EPSs may have with fouling and foaming in an MBR for wastewater treatment. Foaming phenomenon is monitored by performing specific foam-tests: Foam Power, Scum Index, Foam Rating …

Biological Nutrient Removal and Fouling Phenomena in a University of Cape Town Membrane Bioreactor Treating High Nitrogen Loads

2013

The behavior of a University of Cape Town (UCT) membrane bioreactor (MBR) system was investigated for use in biological nutrient removal from real wastewater. The pilot plant was in operation for a period of 165 days, during which an extensive data gathering campaign was conducted. The pilot plant was started up by inoculating it with activated sludge from a nearby wastewater treatment plant, and it was fed by real municipal wastewater characterized by high organic nitrogen concentrations attributable to discharges from industrial wastewater and sporadic landfill leachate. Carbon and biological nutrient removal processes, a sludge production process, and a membrane fouling mechanism were an…

Sequential biological and photocatalysis based treatments for shipboard slop purification: A pilot plant investigation

2019

This study investigated the treatment of a shipboard slop containing commercial gasoline in a pilot plant scale consisting of a membrane biological reactor (MBR) and photocatalytic reactor (PCR) acting in series. The MBR contributed for approximately 70% to the overall slop purification. More precisely, the biological process was able to remove approximately 40%, on average, of the organic pollution in the slop. Nevertheless, the membrane was capable to retain a large amount of organic molecules within the system, amounting for a further 30% of the influent total organic content removal. However, this affected the membrane fouling, thus resulting in the increase of the pore blocking mechani…

Performance of a MBR pilot plant treating high strength wastewater subject to salinity increase: Analysis of biomass activity and fouling behaviour

2013

Membrane bioreactors produce high quality effluents that could be suitable for reuse. However, when treating high strength wastewater subject to a salinity increase, a modification of biomass characteristics may occur. This circumstance is of importance, since it can have a significant impact in terms of biokinetic as well as fouling behaviour. The aim of the study was to evaluate the performance of a pilot plant MBR, in terms of biomass activity and membrane fouling, fed with high strength synthetic wastewater, when subject to a salinity increase. With normal salinity, the pilot plant showed high removal efficiencies and high biomass respiratory activity. On the other hand, the salinity in…

Aerobic granular sludge treating shipboard slop: Analysis of total petroleum hydrocarbons loading rates on performances and stability

2018

Abstract The work focuses on the feasibility of treating slop with aerobic granular sludge. For this purpose, a 3.5 L granular sequencing batch reactor was activated and it was monitored for 156 days. The experimental campaign was divided into two periods, named Period I (100 days) and Period II (56 days). Total Petroleum Hydrocarbon (TPH) concentration in the slop was, on average, equal to 6.8 ± 1.5 mg L−1 and 13 ± 1.5 mg L−1 in Period I and Period II respectively. The obtained results during the first experimental period indicated that about 80 days were required to reach steady state with mature granules, when TPHs removal efficiency was approximately 90%. The results indicated that both…

Aerobic granular sludge treating anaerobically pretreated brewery wastewater at different loading rates.

2020

Abstract In this study, three different aerobic granular sludge (AGS) reactors fed with anaerobically pre-treated brewery wastewater were studied. The AGS reactors were operated under different conditions including organic loading rates (OLR) between 0.8 and 4.1 kg COD m−3 d−1, C:N:P ratios (100:10:1 and 100:6:1) and food to microorganism ratios (F/M) between 0.8 ± 0.6 and 1.2 ± 0.5 and 0.9 ± 0.3 kg-TCOD kg-VSS−1d−1. Stable granulation was achieved within two weeks and the size of the granules increased according to the OLR applied. The results indicated that low C:N:P and F/M ratios were favorable to achieve stable aerobic granules in the long term. The carbon removal rate was load-indepen…

Comparison between hybrid moving bed biofilm reactor and activated sludge system: a pilot plant experiment

2010

The paper presents the comparison between the traditional activated sludge system (AS) and a hybrid moving bed biofilm reactor (HMBBR). In particular, an experimental campaign has been carried out at the WWTP in Palermo (Italy), on a pilot plant consisting of two pre-anoxic schemes. The aerated tank of the HMBBR line was filled with suspended carriers (AnoxKaldnes™ K1), with a 30% filling ratio. The hydraulic load of the HMBBR line was increased up to two times the AS one. Further, in order to distinguish the additional contribution of the attached biomass for the HMBBR system, in the two lines the Mixed Liquor Suspended Solids (MLSS) was maintained as equal as possible. The monitoring peri…

Treatment of high strength industrial wastewater with membrane bioreactors for water reuse: Effect of pre-treatment with aerobic granular sludge on s…

2019

Abstract In this study, the treatment of citrus wastewater with membrane bioreactors (MBRs) under different configurations was investigated for water reuse. In particular, one MBR and one aerobic granular sludge MBR (AGS + MBR) bench scale plants were operated for 60 days. The experimental campaign was divided into two periods. In Phase I, a conventional hollow fiber MBR was employed for the treatment of the raw high strength wastewater, whereas in Phase II a combination of in-series reactors (AGS + MBR) was adopted for the treatment of the high strength citrus wastewater The results demonstrated that both plant configurations enabled very high COD removal, with average values close to 99%.…

Rainwater Reuse in Urban Areas: A Mathematical Model and a Long-Term Modelling Approach

2018

Natural water resources are becoming increasingly limited due to global-scale climate change and water availability issues have become so severe that they must be addressed. Given these issues, reuse of wastewater and rainwater provides a promising way to cope with water shortages. This paper describes an investigation into the efficiency of rainwater usage systems. A conceptual model was built to assess the behaviour of rainwater tanks and their effectiveness in coping with water shortages. The study is based on a long-term simulation (12 years) of different rainwater reuse tank schemes. The associated reductions in residential freshwater demand (water reuse efficiency) and wet-weather run…

Effect of chemical and biological surfactants on activated sludge of MBR system: Microscopic analysis and foam test

2015

Abstract A bench-scale MBR unit was operated, under stressing condition, with the aim of stimulating the onset of foaming in the activated sludge. Possible synergies between synthetic surfactants in the wastewater and biological surfactants (Extra-Cellular Polymeric Substances, EPSs) were investigated by changing C/N ratio. The growth of filamentous bacteria was also discussed. The MBR unit provided satisfactory overall carbon removal overall efficiencies: in particular, synthetic surfactants were removed with efficiency higher than 90% and 95% for non-ionic and ionic surfactants, respectively. Lab investigation suggested also the importance to reduce synthetic surfactants presence entering…

Combination of the OSA process with thermal treatment at moderate temperature for excess sludge minimization

2019

Abstract This study investigated the chance to couple the conventional Oxic Settling Anaerobic (OSA) process with a thermic treatment at moderate temperature (35 °C). The maximum excess sludge reduction rate (80%) was achieved when the plant was operated under 3 h of hydraulic retention time (HRT). Compared with the conventional OSA system, the thermic treatment enabled a further improvement in excess sludge minimization of 35%. The observed yield coefficient decreased from 0.25 gTSS gCOD−1 to 0.10 gTSS gCOD−1 when the temperature in the anaerobic reactor was increased to 35 °C, despite the lower HRT (3 h vs 6 h). Moreover, the thermic treatment enabled the decrease of filamentous bacteria,…

Hybrid moving bed biofilm reactors: a pilot plant experiment.

2008

The growing increment of the urbanization and on the other hand, the even more strict effluent limits imposed by the Water Framework Directive for the receiving water body quality state have lead to a need of upgrading several existing WWTP. With this respect HMBBR systems are an innovative solution since allow to upgrade existing high loaded WWTP without building new tanks. However, some uncertainties in their design, maintenance as well as performance have to be addressed due to their recent acquisition compared with well consolidated technologies such as activated sludge systems. In this light, a data gathering campaign on a HMBBR pilot plant has been performed. The aim was to detect the…

Biomethane Production from Anaerobic Co-Digestion of Selected Organic Fraction of Municipal Solid Waste (OFMSW) with Sewage Sludge: Effect of the Ino…

2021

The aim of this study was to evaluate the effect of the inoculum to substrate ratio (ISR) and the mixture ratio between organic fraction of municipal solid waste (OFMSW) and sewage sludge (SS) on the methane production potential achievable from anaerobic co-digestion (AcoD). Biochemical Methane Potential (BMP) assays at mesophilic temperature were used to determine the best AcoD configuration for maximizing methane yield and production rate, as well as to address possible synergistic effects. The maximum methane yield was observed at ISR of 1 and 60% OFMSW: 40% SS as co-digestion mixture, whereas the highest methane production rate was achieved at ISR of 2 with the same mixture ratio (207 m…

Study of aerobic granular sludge stability in a continuous-flow membrane bioreactor.

2015

A granular continuous-flow membrane bioreactor with a novel hydrodynamic configuration was developed to evaluate the stability of aerobic granular sludge (AGS). Under continuous-flow operation (Period I), AGS rapidly lost their structural integrity resulting in loose and fluffy microbial aggregates in which filamentous bacteria were dominant. The intermittent feeding (Period II) allowed obtaining the succession of feast and famine conditions that favored the increase in AGS stability. Although no further breakage occurred, the formation of new granules was very limited, owing to the absence of the hydraulic selection pressure. These results noted the necessity to ensure, on the one hand the…

Effect of C/N shock variation on the performances of a moving bed membrane bioreactor.

2015

Abstract The effect of a sharp variation of C/N ratio in a moving bed membrane bioreactor (MB-MBR) pilot plant treating high strength wastewater has been investigated. The experimental campaign was divided into two periods, each characterized by a different C/N ratio (namely, 2.5 and 15, Period 1 and Period 2, respectively). The MB-MBR system was analyzed in terms of organic carbon removal, nitrification efficiency, biokinetic activity and fouling behavior. The results showed that the nitrification process was severely affected by lower C/N value and by high concentration of ammonia. It was noticed an extensive stress effect on the autotrophic bacteria. Furthermore, it was observed an incre…

Characterization of Biomass Activity in Conventional and Hybrid MBR Pilot Plants by Means of Respirometric Techniques

2012

abstract

Aerobic granular sludge treating high strength citrus wastewater: Analysis of pH and organic loading rate effect on kinetics, performance and stabili…

2017

Abstract In the present paper, the feasibility of citrus wastewater treatment with aerobic granular sludge sequencing batch reactors (AGSBR) was investigated. Two AGSBRs (named R1 and R2, respectively) were operated for 90 days under different organic loading rates (OLR) and pH in two experimental periods. The OLR ranged approximately between 3.0 kg TCOD m−3d−1 and 7 kg TCOD m−3d−1 during Period I, whereas between 7 kg TCOD m−3d−1 and 15 kg TCOD m−3d−1 during Period II. pH was maintained at 7.0 and 5.5 in R1 and R2, respectively. The results revealed that under high OLR and unbalanced feast/famine regime (Period I), the development of fast-growing microorganisms (fungi and filamentous bacte…

Occurrence of Microplastics in Waste Sludge of Wastewater Treatment Plants: Comparison between Membrane Bioreactor (MBR) and Conventional Activated S…

2022

In this study, the presence of microplastics in the sludge of three wastewater treatment plants (WWTPs) was examined. The investigated WWTPs operated based on a conventional activated sludge (CAS) process, with (W1) or without (W2) primary clarification, and a membrane bioreactor process (MBR) (W3). The microplastics (MPs) concentration in the samples of W3 was approximately 81.1 ± 4.2 × 103 particles/kg dry sludge, whereas MPs concentrations in W1 and W2 were 46.0 ± 14.8 × 103 particles/kg dry sludge and 36.0 ± 5.2 × 103 particles/kg dry sludge, respectively. Moreover, MPs mainly consisted of fragments (66–68%) in the CAS plants, whereas the fra…

Particle size distribution and biomass growth in a submerged membrane bioreactor

2006

Submerged membrane bioreactors (MBR)associate in a single treatment unit a process ofbiological treatment and a phase of solid/liquidseparation by membrane filtration. Due to reduced membrane porosity, suspendedsolids and large amount of bacteria and virusesmay be retained in the reactor; consequently, highbiomass concentration is generally established inthe system. Indeed, this latter circumstance leadsto obtain a system able to operate with a low F/Mand high SRT and hence, as a result, a low sludgeproduction. In technical literature, the definition of fou-lants in MBR systems is a controversial task.More specifically, the influence of TSS onmixed liquor filterability has not been yet full…

Foaming in membrane bioreactors: Identification of the causes

2012

Membrane bioreactors (MBRs) represent by now a well established alternative for wastewater treatment. Their increasing development is undoubtedly related to the several advantages that such technology is able to guarantee. Nevertheless, this technology is not exempt from operational problems; among them the foaming still represents an "open challenge" of the MBR field, due to the high complexity of phenomenon. Unfortunately, very little work has been done on the foaming in MBRs and further studies are required. Actually, there is not a distinct difference between conventional activated system and MBR: the main difference is that the MBR plants can retain most Extracellular Polymeric Substan…

The role of extracellular polymeric substances on aerobic granulation with stepwise increase of salinity

2018

Abstract A granular sequencing batch reactor (GSBR) worked for 164 days to study the effect of salinity on aerobic granulation. The feeding had an organic loading rate (OLR) of 1.6 kg COD⋅m −3 ⋅d −1 and a gradual increase of salinity (from 0.30 to 38 g NaCl − ⋅L −1 ) to promote a biological salt-adaptation. First aggregates (average diameter ≈ 0.4 mm) appeared after 14 days. Extracellular polymeric substances (EPSs) analyses revealed that proteins were mainly higher than polysaccharides, and microorganisms metabolized EPSs as additional carbon source, mostly in feast phase, to face the energy demand for salinity adaptation. No significant worsening of organic matter removal was observed. Th…

Comparison between two MBR pilot plants treating synthetic shipboard slops: effect of salinity increase on biological performance, biomass activity a…

2017

The paper reports the main results of an experimental campaign carried out on two bench scale pilot plants for the treatment of synthetic shipboard slops. In particular, two membrane bioreactors (MBRs) with submerged configuration were analyzed. One MBR pilot plant (namely, Line A) was fed with synthetic shipboard slop and was subjected to a gradual increase of salinity. Conversely, the second MBR pilot plant (namely, Line B) was fed with the same synthetic shipboard slop but without salt addition, therefore operating as a “control” unit. Organic carbon, hydrocarbons and ammonium removal, kinetic constants, extracellular polymeric substances (EPSs) production and membranes fouling rates…

Effect of a co-substrate supply in a MBR treating shipboard slop: Analysis of hydrocarbon removal, biomass activity and membrane fouling tendency

2018

The paper reports the main results of an experiment carried out on a membrane bioreactor (MBR) plant designed for the treatment of shipboard slops. With a view of a co-treatment process of the slop with other wastewaters, sodium acetate, as external co-substrate, was supplied (high dosage – Period 1, low dosage – Period 2) to evaluate its effects on hydrocarbons removal. The MBR pilot plant enabled approximately 99% of total petroleum hydrocarbon (TPH) removal during the entire experiment, confirming the robustness of the MBR technology for the treatment of slops. The chromatography/mass spectrometry analysis showed that the removal efficiency for each alkane was close to the value observed…

Biokinetic Behaviour of Autochthonous Halophilic Biomass at Different Salinity: Comparison Between Activated Sludge and Granular Sludge Systems

2017

The main goal of this study was the evaluation of the impact of increasing salinity on halophilic biomass in forms of flocculent and granular sludge for the treatment of hypersaline fish-canning wastewater, focusing on the metabolic behavior of autotrophic biomass. For this purpose, two sequencing batch reactors, one with aerobic granular sludge (GSBR) and the other with flocculent activated sludge (SBR) were monitored. In both reactors, a halophilic biomass was cultivated from a real saline wastewater collected from a fish-canning industry. The salt concentration was stepwise increased (2 gNaCl L-1) from 30 gNaCl L-1 to 50 gNaCl L-1. Therefore, ammonia and nitrite uptake rates for granular…

Aerobic granular sludge reactor treating anaerobically pretreated brewery wastewater at different loading rates

2018

Small and medium breweries discharging to municipal sewers without treatment generate significant loads with typical concentrations reported by Valta et al. (2014) as 2-6 g COD L-1, 25-80 mg TN L-1, 10-50 mg TP L-1, with pH between 4.5 and 12. Treatment of the high-strength wastewater requires specialized low footprint processes, such as aerobic granular sludge (AGS), capable of high-rate degradation, as well as simultaneous nitrogen and phosphorous removal (Wang et al., 2007). The objective of this study was to evaluate the start-up period of AGS receiving brewery wastewater after initial anaerobic pretreatment.

Optimization of acetate production from citrus wastewater fermentation

2021

Abstract Citrus wastewater is a sugar-rich waste stream suitable for the recovery of energy of material from its treatment. In this study, fermentation of citrus wastewater was carried out to assess the optimal conditions to maximize the bioconversion of the organic substrate into acetate. Unbalanced nutrient (C: N: P 200:0.1:0.1) enabled the highest acetate production. The presence of the particulate organic fraction enabled to obtain a higher acetate concentration regardless the initial COD concentration. Initial pH values higher than 5 did not cause substantial differences on the maximum bioconversion of COD into acetate in Trial 3, whereas pH lower than 5 hindered the hydrolysis process…

Fate of aerobic granular sludge in the long-term: The role of EPSs on the clogging of granular sludge porosity

2016

This work aims to investigate the stability of aerobic granular sludge in the long term, focusing on the clogging of the granular sludge porosity exerted by the extracellular polymeric substances (EPSs). The effects of different cycle lengths (short and long-term cycle) on the granular sludge stability were investigated. Results obtained outlined that during the short duration cycle, the formation and breakage of the aerobic granules were continuously observed. During this period, the excess of EPS production contributed to the clogging of the granules porosity, causing their breakage in the long run. During the long-duration cycle, the extended famine period entailed a greater EPSs consump…

Comparison between ozonation and the OSA process: analysis of excess sludge reduction and biomass activity in two different pilot plants

2012

The excess biomass produced during biological treatment of municipal wastewater represents a major issue worldwide, as its disposal implies environmental, economic and social impacts. Therefore, there has been a growing interest in developing technologies to reduce sludge production. The main proposed strategies can be categorized according to the place inside the wastewater treatment plant (WWTP) where the reduction takes place. In particular, sludge minimization can be achieved in the wastewater line as well as in the sludge line. This paper presents the results of two pilot scale systems, to evaluate their feasibility for sludge reduction and to understand their effect on biomass activit…

Comparison between kinetics of autochthonous marine bacteria in activated sludge and granular sludge systems at different salinity and SRTs.

2019

Biological nutrient removal performances and kinetics of autochthonous marine biomass in forms of activated sludge and aerobic granular sludge were investigated under different salinity and sludge retention time (SRT). Both the biomasses, cultivated from a fish-canning wastewater, were subjected to stepwise increases in salinity (+2 gNaCl L−1), from 30 gNaCl L−1 up to 50 gNaCl L−1 with the aim to evaluate the maximum potential in withstanding salinity by the autochthonous marine biomass. Microbial marine species belonging to the genus of Cryomorphaceae and of Rhodobacteraceae were found dominant in both the systems at the maximum salinity tested (50 gNaCl L−1). The organic carbon was remove…

Integrated production of biopolymers with industrial wastewater treatment: Effects of OLR on process yields, biopolymers characteristics and mixed mi…

2022

The production of polyhydroxyalkanoates (PHA) using industrial wastewaters as feedstocks is a current and challenging topic. This study investigated the production of biopolymers by a mixed microbial culture under different OLRs equal to 1 kgCOD m-3d-1 (Period 1), 2 kgCOD m-3d-1 (Period 2) and 3 kgCOD m-3d-1 (Period 3). The maximum PHA content was achieved in Period 2 (0.38 gPHA gTSS-1), whereas lower values were obtained in Period 1 (0.13 gPHA gTSS-1) and Period 3 (0.26 gPHA gTSS-1). Overall, the maximum PHA productivity resulted equal to 0.08 gPHA L-1h-1 (P2), 0.05 gPHA L-1h-1 (P1) and 0.04 gPHA L-1h-1 (P3), respectively. The molecular weight of the PHA increased from Period 1 (250 kDa) t…

Shortcut nitrification-denitrification by means of autochthonous halophilic biomass in an SBR treating fish-canning wastewater

2017

Abstract Autochthonous halophilic biomass was cultivated in a sequencing batch reactor (SBR) aimed at analyzing the potential use of autochthonous halophilic activated sludge in treating saline industrial wastewater. Despite the high salt concentration (30 g NaCl L −1 ), biological oxygen demand (BOD) and total suspended solids (TSS), removal efficiencies were higher than 90%. More than 95% of the nitrogen was removed via a shortcut nitrification-denitrification process. Both the autotrophic and heterotrophic biomass samples exhibited high biological activity. The use of autochthonous halophilic biomass led to high-quality effluent and helped to manage the issues related to nitrogen removal…

Biological minimization of excess sludge in a membrane bioreactor: Effect of plant configuration on sludge production, nutrient removal efficiency an…

2018

Abstract Excess sludge minimization was studied in a MBR with pre-denitrification scheme. Sludge minimization, nitrogen removal performance and membrane fouling tendency were investigated in two configurations, characterized by a different position of the sludge retention reactor (SRR). In particular, the SRR was placed: i) in the return activated sludge line (Anaerobic Side-Stream Reactor – ASSR configuration) and ii) in the mainstream between the anoxic and aerobic reactor (Anaerobic Main-Stream Reactor – AMSR configuration). The achieved results demonstrated that the ASSR enabled a higher excess sludge reduction (74% vs 32%), while achieving lower biological nitrogen removal (BNR) (TN = …

Waste activated sludge dewaterability: comparative evaluation of sludge derived from CAS and MBR systems

2016

Nowadays, sludge dewatering is one of the greatest operational cost to wastewater treatment cycle. Specifically, 1t of fresh sludge to be disposed is composed, on average, by 0.25 - 0.30t of suspended solids, with an average cost for treatment and disposal around 280 - 470 €/t of suspended solids. Despite several technologies have been developed with the focus to reduce also the specific sludge production, still mechanical dewatering represents a crucial step to limit the amount of sludge to be disposed. Many physical–chemical parameters influence the sludge dewaterability: floc structure, particle size, bound water content, surface charge and hydrophobicity, Extracellular Polymeric Substan…

Assessment of landfill leachate biodegradability and treatability by means of allochthonous and autochthonous biomasses

2020

Abstract The biodegradability and treatability of a young (3 years old) municipal landfill leachate was evaluated by means of chemical oxygen demand (COD) fractionation tests, based on respirometric techniques. The tests were performed using two different biomasses: one cultivated from the raw leachate (autochthonous biomass) and the other collected from a conventional municipal wastewater treatment plant after its acclimation to leachate (allochthonous biomass). The long term performances of the two biomasses were also studied. The results demonstrated that the amount of biodegradable COD in the leachate was strictly dependent on the biomass that was used to perform the fractionation tests…

Performance of a hybrid activated sludge/biofilm process for wastewater treatment in a cold climate region: Influence of operating conditions

2013

a b s t r a c t The main aim of the study was to investigate a hybrid MBBR process, mostly in terms of organic matter removal and nitrification, when operating with different values of the mixed liquor sludge retention time (SRT), and highlighting the influence of temperature on the process. Based on experience in practice it was hypothesized that nitrification could be maintained at far lower SRT's than in conventional activated sludge systems and with high organic loading rates applied. A field gathering campaign has been carried out on a hybrid activated sludge/biofilm. The obtained results highlighted that the pilot plant was capable to remove the organic matter at loading rates up to 3…

Simultaneous nitrogen and organic carbon removal in aerobic granular sludge reactors operated with high dissolved oxygen concentration

2013

Simultaneous nitrification and denitrification (SND) together with organic removal in granules is usually carried out without Dissolved Oxygen (DO) concentration control, at ‘‘low DO’’ (with a DO 7–8 mg/L, during feast and famine conditions respectively). In particular, different strategies of cultivation and several organic and nitrogen loading rate have been applied, in order to eval- uate the efficiencies in SND process without dissolved oxygen control. The results show that, even under conditions of high DO concentration, nitrogen and organic matter can be simultaneously removed, with efficiency >90%. Nevertheless, the biological conditions in the inner layer of the granule may change sig- …

Treatment of Oily Wastewater with Membrane Bioreactor Systems

2017

The aim of the present work was to investigate the behavior of a membrane bioreactor (MBR) system for the treatment of oily wastewater. A bench scale MBR was fed with synthetic wastewater containing diesel fuel. Organic carbon, hydrocarbon and ammonium removal, kinetic constants, extracellular polymeric substances production, and membrane fouling rates were monitored. The MBR plant was operated for more than 200 days, and the results highlighted good carbon removal and nitrification, suggesting a sort of biomass adaptation to hydrocarbons. Membrane fouling analysis showed an increase in total resistance, likely due to hydrocarbons, which caused an irreversible fouling (pore blocking) mainly…

Applicazione della tecnologia MABR per l’incremento della capacità depurativa di impianti esistenti

2019

La necessità di adeguare e/o ampliare gli esistenti impianti biologici di trattamento delle acque reflue, sia urbane che industriali, sia per potenziarne la capacità depurativa che per ottemperare al rispetto di limiti allo scarico per gli effluenti trattati sempre più restrittivi, si scontra sempre più di frequente con la difficoltà a reperire adeguate aree di espansione degli impianti. Pertanto, negli ultimi decenni sono state proposte nuove tecnologie atte a ridurre al massimo il volume dei reattori biologici, o incrementando la concentrazione di biomassa presente nel sistema e la capacità dello stadio finale del trattamento biologico, ossia quello di separazione solido-liquido, come nel…

An innovative respirometric method to assess the autotrophic active fraction: Application to an alternate oxic-anoxic MBR pilot plant

2016

An innovative respirometric method was applied to evaluate the autotrophic active fraction in an alternate anoxic/oxic membrane bioreactor (MBR) pilot plant. The alternate cycle (AC) produces a complex microbiological environment that allows the development of both autotrophic and heterotrophic species in one reactor. The present study aimed to evaluate autotrophic and heterotrophic active fractions and highlight the effect of different aeration/non aeration ratios in a AC-MBR pilot plant using respirometry. The results outlined that the autotrophic active fraction values were consistent with the nitrification efficiency and FISH analyses, which suggests its usefulness for estimating the ni…

Oil-degrading bacteria from a membrane bioreactor (BF-MBR) system for treatment of saline oily waste: Isolation, identification and characterization …

2016

A collection of forty-two (42) strains was obtained during microbiological screening of a Membrane Bioreactor (MBR) system developed for the treatment of saline oily waste originated from marine transportation. The diversity of the bacterial collection was analyzed by amplification and sequencing of the 16S rRNA gene. Taxonomic analysis showed high level of identity with recognized sequences of seven (7) distinct bacterial genera (Alcanivorax, Erythrobacter, Marinobacter, Microbacterium, Muricauda, Rhodococcus and Rheinheimera). The biotechnological potential of the isolates was screened considering an important factor such as the biosurfactant production. In particular fourteen (14) biosur…

Cultivation of granular sludge with hypersaline oily wastewater

2015

The time required to stabilise mature aerobic granules is rather variable. In addition, cultivation time and the structural characteristics of granules seem to be related to the nature of wastewater influent. Granular sludge has been used for the treatment of several industrial wastewaters, but nothing has been reported about wastewater characterized by the simultaneous presence of hydrocarbons and high chloride concentration. In this work, the authors analysed the granulation process and performance as well as the physical characteristics of aerobic granules in two Granular Sequencing Batch Airlift Reactors (GSBARs), fed with acetate-based synthetic wastewater in reactor 1 (R1) and with a …

Simultaneous sludge minimization, biological phosphorous removal and membrane fouling mitigation in a novel plant layout for MBR.

2020

Abstract The integration of one anaerobic reactor in the mainstream (AMSR) of a pre-denitritication-MBR was evaluated with the aim to achieve simultaneous sludge minimization and phosphorous removal. The excess sludge production was reduced by 64% when the AMSR was operated under 8 h of hydraulic retention time (HRT). The highest nutrients removal performances referred to organic carbon (98%), nitrogen (90%) and phosphorous (97%) were obtained under 8 h of HRT. In contrast, prolonged anaerobic-endogenous conditions were found to be detrimental for all nutrients removal performances. Similarly, the lowest membrane fouling tendency (FR = 0.65∙1011 m−1 d−1) was achieved under 8 h of HRT, where…

Modelling of hybrid moving bed biofilm reactors: a pilot plant experiment.

2007

In recent years there has been an increasing interest in the development of hybrid biofilm reactors, especially in the upgrading of existing WWTP that are no longer able to respect concentration limits. In fact, today's challenge is the achievement of a good aquatic state for the receiving water bodies according to the Water Framework Directive requirements, which indeed limit even more the continuous emissions, i.e. coming from WWTP. This paper presents the setting up of a mathematical model for the simulation of a hybrid MBBR system; the model calibration/validation has been carried out considering a field gathering campaign on an experimental pilot plant. The main goal is to gain insight…

The role of extracellular polymeric substances (EPS) on aerobic granules formation: comparison between a case of synthetic wastewater supply and anot…

2017

The paper focused on the evolution and the comparison of the extracellular polymeric substances (EPSs) content during the granulation process in two Granular Sequencing Batch Airlift Reactors (GSBAR) (3,5 L) fed with synthetic (R1) and industrial wastewater (R2). The results showed that in both the reactors the EPSs, in particular proteins (PN), were mainly produced during the feast phase because of the high substrate availability, especially under conditions of metabolic stress. Then, the EPSs content reduced during the famine period, because of biodegradation by bacteria. More in detail, during the granulation process, a greater polysaccharides (PS) consumption occurred in both reactors, …

Start-up with or without inoculum? Analysis of an SMBR pilot plant.

2010

This study analysed a submerged membrane bioreactor (SMBR) start-up with the purpose of determining the best conditions to carry it out. In order to do this, a hollow fibre membrane module was installed in a submerged configuration in a pilot aerobic reactor. The experiment was then divided in two phases, lasting 65 days each. During phase 1, the pilot plant was started-up without inoculum of activated sludge and no sludge, withdrawal was performed. Conversely, in phase 2, the MBR pilot plant was started-up with sludge inoculum and the sludge concentration was kept constant. In both phases, the volumetric loading rate applied to the pilot plant was kept constant. The authors analysed the di…

Performances of a granular sequencing batch reactor (GSBR).

2007

Aerobic granulation in sequencing batch reactors is widely reported in literature and in particular in SBAR (Sequencing batch airlift reactor) configuration, due to the high localised hydrodynamic shear forces that occur in this type of configuration. The aim of this work was to observe the phenomenon of the aerobic granulation and to confirm the excellent removal efficiencies that can be achieved with this technology. In order to do that, a laboratory-scale plant, inoculated with activated sludge collected from a conventional WWTP, was operated for 64 days: 42 days as a SBAR and 22 days as a SBBC (sequencing batch bubble column). The performances of the pilot plant showed excellent organic…

The role of EPS concentration in MBR foaming: analysis of a submerged pilot plant.

2010

Foaming in Membrane BioReactor (MBR) is a frequently discussed topic. Some authors reported that the phenomenon is due to filamentous organisms, like at Conventional Activated Sludge (CAS) plants. However, in recent years, other authors reported that the Extra-cellular Polymer Substances (EPSs) concentration is an important factor for controlling foam as well. Nevertheless, even if a number of MBR plants are affected by foaming, presently there are no suitable methods to evaluate the phenomenon. To facilitate the study of this controversial phenomenon in an MBR system, certain foam tests proposed in the past for CASPs were investigated. The results of the tests were able to adequately measu…

Physical properties and Extracellular Polymeric Substances pattern of aerobic granular sludge treating hypersaline wastewater.

2017

The modification of the physical properties of aerobic granular sludge treating fish-canning wastewater is discussed in this paper. The structure and composition of the Extracellular Polymeric Substances (EPSs) were analyzed at different salinity levels and related to granules stability. Results outlined that the total EPSs content increased with salinity, despite the EPSs increment was not proportional to the salt concentration. Moreover, the EPSs structure was significantly modified by salinity, leading to a gradual increase of the not-bound EPSs fraction, which was close to the 50% of the total EPSs content at 75 g NaCl L-1. The increasing salt concentration modified also the EPSs compos…

Application of the Oxic-Settling-Anaerobic Process in a Membrane Bioreactor for Excess Sludge Reduction

2017

The main goal of this study was the evaluation of the excess sludge reduction in a MBR for biological nitrogen removal (BNR) through the implementation of the Oxic-Settling-Anaerobic (OSA) process. For this purpose, a MBR pilot plant (42 L volume) was realized according to a pre-denitrification scheme. The whole experimentation was divided into two periods, named Period 1 and Period 2, respectively. In Period 1 the pilot plant was started-up and the excess sludge production was evaluated. In Period 2 the plant configuration was partially modified by inserting an anaerobic reactor into the return activated sludge (RAS) line to realize an OSA configuration. In Period 1, the Yobs resulted equa…

Influence of the Oxic-Settling-Anaerobic (OSA) Process on Methane Production by Anaerobic Digestion of Sewage Sludge

2023

The present study evaluated different sludge-reduction mechanisms in the oxic-settling-anaerobic (OSA) process in terms of their effects on methane productivity by anaerobic digestion of sewage sludge. Two different layouts were investigated for the sludge return from an anaerobic side-stream reactor (ASSR) to the anoxic (scheme A) or the aerobic (scheme B) reactor of a pre-denitrification plant. Biochemical methane-potential (BMP) assays performed on the excess sludge revealed that scheme A promoted an overall increase of methane production in the OSA (20 mLCH4 gVSS−1d−1, +19%), although compared with a control CAS plant a significant decrease in the excess sludge production (3…

A comprehensive comparison between halophilic granular and flocculent sludge in withstanding short and long-term salinity fluctuations

2018

The effects of salinity fluctuations on the activity of autochthonous halophilic bacteria in aerobic granular sludge (AGS) and flocculent activated sludge (FAS) reactors were investigated. The response of nitrifiers and denitrifiers activity to drastic and moderate salinity shocks in the short-term (ST) and long-term (LT) was examined. The BOD5removal efficiency decreased only in the reactors subjected to the drastic LT salinity increase. Nevertheless, stable performances were achieved 18 days after the shock in the AGS-R1 (90%), whereas after 27 days in the FAS-R1 (82%). The loss in nitritation efficiency was higher in the FAS reactors and was proportional to the shock intensity. Nitritati…

Membrane bioreactors sludge: From production to disposal

2020

Abstract This chapter reviews the MBR activated sludge from production to disposal. Starting from sludge characterization, the chapter first presents the features of MBR sludge (morphology and EPS chemical composition), also in terms of differences with the activated sludge from conventional activated sludge plants. Sludge dewaterability is then discussed, focusing on the differences between aerobically and anaerobically digested sludge. An analysis of the costs related to MBR sludge treatment and disposal also is presented in order to provide a framework for a sustainable MBR sludge management.

The role of EPS in the foaming and fouling for a MBR operated in intermittent aeration conditions

2016

Abstract This work investigates the causes of foaming and fouling in an Intermittent Aerated – Membrane BioReactor (IA-MBR) used for wastewater treatment. The experiment was divided into three periods with different aerated regimes expressed with different t aeration /t cycle ratio (Period I: 60 min/180 min, Period II: 80 min/180 min, Period III: 30 min/90 min). The advanced foaming tests used allow the study of the role of extracellular polymeric substances (EPSs) on foaming and fouling. In general, in the Periods I and II, good correlations between the EPSs and the Modified Scum Index without purification (MSI 0 ) and the Foam Power were observed. The results shown that the filamentous mi…

Enhanced Sewage Sludge Drying with a Modified Solar Greenhouse

2022

This work reports the results obtained with an innovative configuration of a closed-static solar greenhouse for sludge drying. The novelty of the solar greenhouse configuration consisted in using a forced ventilation system to provide hot air for sludge drying and the utilization of solar irradiation for energy supply. Wet sewage sludge (97% humidity) was successfully dried up to a residual humidity close to 5% after 25 days during wintertime. The increase of the airflow rate supplied under the sludge bed improved the sludge drying rate. Moreover, the fraction of volatile suspended solids decreased from 70% to 41% after 13 days, indicating that air supply promoted the simultaneous stabiliza…

Simultaneous nitritation-denitritation for the treatment of high-strength nitrogen in hypersaline wastewater by aerobic granular sludge

2015

Abstract Fish processing industries produce wastewater containing high amounts of salt, organic matter and nitrogen. Biological treatment of such wastewaters could be problematic due to inhibitory effects exerted by high salinity levels. In detail, high salt concentrations lead to the accumulation of nitrite due to the inhibition of nitrite-oxidizing bacteria. The feasibility of performing simultaneous nitritation and denitritation in the treatment of fish canning wastewater by aerobic granular sludge was evaluated, and simultaneous nitritation–denitritation was successfully sustained at salinities up to 50 gNaCl L −1 , with a yield of over 90%. The total nitrogen concentration in the efflu…

Comparison between moving bed-membrane bioreactor (MB-MBR) and membrane bioreactor (MBR) systems: Influence of wastewater salinity variation

2014

Two pilot plant systems were investigated for the treatment of wastewater subject to a gradual increase of salinity. In particular, a membrane bioreactor (MBR) and a moving bed biofilm membrane bioreactor (MB-MBR) were analyzed. Carbon and ammonium removal, kinetic constants and membranes fouling rates have been assessed. Both plants showed very high efficiency in terms of carbon and ammonium removal and the gradual salinity increase led to a good acclimation of the biomass, as confirmed by the respirometric tests. Significant biofilm detachments from carriers were experienced, which contributed to increase the irreversible superficial cake deposition. However, this aspect prevented the por…

Performance of membrane bioreactor (MBR) systems for the treatment of shipboard slops: Assessment of hydrocarbon biodegradation and biomass activity …

2015

In order to prevent hydrocarbon discharge at sea from ships, the International Maritime Organization (IMO) enacted the MARPOL 73/78 convention in which any oil and oil residue discharged in wastewater streams must contain less than 5. ppm hydrocarbons. Effective treatment of this petroleum-contaminated water is essential prior to its release into the environment, in order to prevent pollution problem for marine ecosystems as well as for human health. Therefore, two bench scale membrane bioreactors (MBRs) were investigated for hydrocarbon biodegradation. The two plants were initially fed with synthetic wastewater characterised by an increasing salinity, in order to enhance biomass acclimatio…

Evaluation of biomass activity and wastewater characterization in a UCT-MBR pilot plant by means of respirometric techniques

2011

Abstract Over the last two decades, Membrane Bioreactors (MBRs) emerged even more for wastewater treatment, ensuring high removal efficiencies as well as very small footprint requirements. Indeed, in this kind of process, a modification in biomass activity and viability can exist compared to that of a CAS process. In this context, respirometric analysis represents a reliable tool in order to evaluate the actual biomass kinetic parameters, to insert in mathematical models in the design phase, as well as to monitor the biomass viability, especially when these processes are operated with high SRT values. The paper presents some results of respirometric techniques applied for the characterisati…

Analisi della fase di start-up di un bireattore a membrana.

2006

Comparison between MBR and MB-MBR pilot plants subject to a gradual salinity increase: analysis of biokinetic and fouling behaviour

2014

Two pilot plants were investigated for the treatment of wastewater subject to a gradual increase of salinity. In particular, a membrane bioreactor (MBR) and a moving bed biofilm membrane bioreactor (MB-MBR) were studied. Carbon and ammonium removal, kinetic constants and membranes fouling rates have been assessed. Both plants showed very high efficiency in terms of carbon and ammonium removal and the gradual salinity increase led to a good acclimation of the biomass, as confirmed by the respirometric tests. Significant biofilm detachments from carriers were experienced, which contributed to increase the irreversible superficial cake deposition. However, this aspect prevented the pore foulin…

Analysis of Biomass Characteristics in MBR and MB-MBR Systems Fed with Synthetic Wastewater: Influence of a Gradual Salinity Increase

2014

The paper presents the results of a field gathering campaign carried out on two different pilot scale membrane bioreactor (MBR) systems, treating synthetic wastewater subject to a gradual increase of salinity. One was a conventional MBR system, while the other was a moving bed biofilm membrane bioreactor (MB-MBR), which combines suspended biomass and biofilm. Indeed, the presence of suspended carriers inside the bioreactor seems to give benefits due to the collisions between the circulating media and the membrane. The aim of the study was the comparison of two configurations in terms of biomass activity characterization and performance (pollutants removal and hydraulic behaviour). The resul…

Caratterizzazione e classificazione di casi di foaming negli impianti a fanghi attivi

2004

Start-up of a submerged membrane bioreactor with complete sludge retention

2005

The role of EPS in fouling and foaming phenomena occurring in an UCT-MBR pilot plant

2012

The aim of this study is to detect a possible relationship between EPS and fouling and EPS and foaming in a University Cape Town (UCT) membrane bioreactor (MBR) pilot plant. The UCT-MBR pilot plant was fed with 40 L/h of real wastewater and monitored for 165 days. Specifically physical/chemical features of influent, permeate and mixed liquor in different sections were analyzed. The fouling phenomenon was studied monitoring the hydraulic resistances of the membrane. The extracellular polymeric substances (EPSs) concentration inside the aerobic tank were also measured. The foaming phenomenon was monitored by performing the Foam Power and Scum Index testes. Results have shown a high correlatio…

OSSERVATORIO SUGLI IMPIANTI DI DEPURAZIONE MBR - Rapporto 2016

2016

I reattori biologici a membrana (MBR, dall’inglese Membrane Biological Reactor) derivano dall’accoppiamento dei tradizionali processi a biomassa sospesa con i processi di filtrazione su membrane microporose o ultraporose, a seconda delle dimensioni nominali dei pori. I maggiori vantaggi legati a questa tecnologia vanno ricercati nella possibilità di eliminare, a valle della fase biologica, quella dei vincoli gestionali ed operativi a quest’ultima connessi. La sostituzione della sedimentazione con una fase di filtrazione su membrane comporta: una notevole riduzione dell’ingombro planimetrico dell’impianto di depurazione, dovuta sia alla eliminazione delle unità di sedimentazione che alla d…

Tecniche per l'incremento della sedimentabilità dei fanghi negli impianti di trattamento di reflui industriali

2007

Modificazione delle caratteristiche delle acque reflue a seguito del loro stoccaggio

2004

High salinity slops treatment through a biofilm-MBR inoculated with halophilic bacteria

2010

Oily wastewater generated, in amounts of millions of tons per year, by ships mainly in engine-rooms (bilge waters) and by washing oil tanks (slops) create a major disposal problem throughout the world because of the persistence and accumulation of xenobiotic compounds in the environment. The high salinity levels (up to 25.000 p.p.m.) and the pollutants concentration limit the chances of discharge into the sewer systems and address the disposal to the sea. This situation severely lowers the discharge limits for most of the “sensible” parameters, such both COD and hydrocarbons. Slops are usually treated by ASP with pretreatment of oil/water separation. There are limited investigations on the …

BIOLOGICAL STABILITY ANALYSIS OF THE OFMSW MATRIX TREATED IN A COMPOSTING PLANT

2011

Composting, mechanical-biological treatment (MBT), biodrying and biostabilization processes of pre-selected organic fraction from municipal solid wastes (OFMSW) have recently become important in municipal solid waste management. Through these treatment processes the potential impacts of the produced wastes and the volume to treat in the landfill are strongly reduced. However, the residual organic matter contained in the treated fraction may provide negative effects when e.g. the treated OFMSW is used as compost. The biological stability degree of the treated matrix provides usefull informations for the final use of it. Indeed, knowing the degree of biological stability of the compost makes …

Biological nutrient removal in a UCT-MBR pilot

2010

In the last years, there has been an increasing awareness about the environment pollution protection. As a consequence, the Environmental Regulation has increased the emission limits imposing, for instance, lower concentrations at the wastewater treatment plant (WWTP) outlets. As a consequence of this fact, several WWTPs are not able to respect the emission limits and need to be upgraded. In view of such needs new technology are emerging and new WWTP solution schemes are being realized. With respects to the nutrient removal enhancing, a possible solution can be the UCT-MBR which couples the University of Cape Town scheme with a Membrane Bioreactor. In the light of such considerations, the s…

Analisi sperimentale e modellistica di formazione del fouling delle membrane nei sistemi MBR

2012

Start-up of a submerged membrane bioreactor with complete sludge retention.

2006

COD and TPH analysis in slops experimental treatment plants: analytical problems.

2015

COD AND TPH ANALYSIS IN SLOPS EXPERIMENTAL TREATMENT PLANTS: ANALYTICAL PROBLEMS. In the last years, the persistence and accumulation of xenobiotic compounds in the environment created many disposal problems of oily wastewater generated by ships, mainly in engine-rooms (bilge waters) and by cleaning of tanker (slops). The high salinity levels (up to 25.000 mgL-1) and the pollutants concentration, both limit the chances of discharge into the sewer systems and address the disposal of these wastewaters to the sea. For these reasons it is necessary to treat such wastewater efficiently before discharging [1]. As a part of a broader project concerning slops treatments, this work addresses issues …

Comparison between two MBR pilot plants treating synthetic shipboard slops: effect of salinity increase on biological performance, biomass activity a…

2015

The paper reports the main results of an experimental campaign carried out on two bench scale pilot plants for treatment of synthetic shipboard slops. In particular, two membrane bioreactors (MBRs) with submerged configuration were analyzed. One MBR pilot plant (namely, Line A) was fed with synthetic shipboard slop and was subjected to a gradual increase of salinity. Conversely, the second MBR pilot plant (namely, Line B) was fed with the same synthetic shipboard slop but without salt addition, therefore operating as a “control” unit. Organic carbon, hydrocarbons and ammonium removal, kinetic constants, extracellular polymeric substances (EPSs) production and membranes fouling rates have be…

The SND process in two granular sequencing batch reactors with different mean granule sizes: a case study.

2013

Advanced course: innovative wastewater treatment and mathematical modelling

2015

During the last years many advances have matured in wastewater treatment both in terms of processes and mathematical modelling approaches. For a new generation of new scientists and engineers entering/working in the wastewater treatment field, the quantity, complexity and diversity of these new developments can be overwhelming. This Advanced Course on Innovative wastewater treatment processes and mathematical modelling will provide a comprehensive overview and a discussion platform for recent advances and trends currently under development in the context of wastewater treatment. This course is aimed at professionals (Master, PhD or equivalent experience) in wastewater treatment and mathemat…

Respirometric assessment of heterotrophic and autotrophic biomass activity in alternate oxic-anoxic MBR pilot plant

2014

The paper reports the main results of an experimental study carried out on a Membrane Biological Reactor (MBR) pilot plant characterized by intermittent aeration. The effect of different aeration/non aeration ratio (TA/TNA) on biomass behavior, in terms of heterotrophic and autotrophic kinetic parameters and active biomass fraction, was studied. Moreover was proposed a method to evaluate the autotrophic active fraction, derived by a combination of the ASM1 model and biokinetic parameters directly evaluated by means of respirometry. The experimental observation outlined that TA/TNA in the cycle didn’t affect heterotrophic biomass kinetic and active fraction. This one instead, resulted strong…

Modelling the changes in time of MSW properties in a landfill.

2005

Oil-degrading bacteria from a membrane bioreactor (MBR) system for treatment of saline oily waste: isolation, identification and characterization of …

2015

This study was focused on the microbial community characterization during operation of a Membrane Bioreactor System, used for the treatment of saline oily wastes, originated from marine transportation. A collection of forty-two (42) strains was obtained during microbiological screening and the bacterial diversity analyzed by amplification and 16S rRNA sequencing. Taxonomic analysis has shown a high level of identity with recognized sequences for a total of seven (7) distinct bacterial genera (Alcanivorax, Erythrobacter, Marinobacter, Microbacterium, Muricauda, Rhodococcus and Rheinheimera). The biotechnological potential of all isolates was identified by the estimate of two key factors, suc…

The effect of hydrocarbon on a pilot plant membrane bioreactor system

2015

The paper reports the main results from an experimental gathering campaign carried out on a bench scale plant for the evaluation of hydrocarbon effect on the system performance. In particular, a membrane bioreactor (MBR) under submerged configuration was analysed. The MBR plant was fed with synthetic wastewater containing hydrocarbons. Organic carbon, hydrocarbons and ammonium removal, kinetic constants, extracellular polymeric substances (EPSs) production and membranes fouling rates have been assessed. The observed results highlighted good system performance in terms of both COD removal and nitrification, thus showing a sort of biomass adaptation to hydrocarbon. Such a result has been also…

Sistemi localizzati di riuso delle acque meteoriche in ambito urbano

2009

Il Foaming negli impianti MBR

2013

Wastewater reuse effect on soil hydraulics characteristics

2004

A survey of tubercolin reactivity in school children and Palermo University medícal school students

1995

Foaming in membrane bioreactor: identification of the causes

2012

The biological foaming was related to the metabolism of certain microorganisms that synthesize and excrete hydrophobic compounds. Recently, by the attention of many researchers the biological foaming in the MBR has attracted, because MBR foam has been also observed in the absence of foam-forming microorganisms, contrarily to conventional activated sludge systems. In this paper the authors investigate the role of EPS and filamentous bacteria analyzing different samples from different MBR pilot plants. In particular, in order to define the macroscopic features and the role of EPS and filamentous bacteria a modified Scum Index (MSI) test was applied. Further a multiple classification of SI was…

Application of respirometric techniques for the characterization of the wastewater treated in the “Acqua dei Corsari” treatment plant of Palermo

2004

Stima del fenomeno del foaming nei sistemi a fanghi attivi

2006

RIMOZIONE COMBINATA DI CARBONIO E NUTRIENTI IN DUE REATTORI SBR GRANULARI: EFFETTO DELLA DIMENSIONE DEI GRANULI

2015

Sono state investigate le performance di due impianti SBR (Sequencing Batch Reactor), alimentati con refluo sintetico a base di acetato di sodio e funzionanti con due differenti tipi di fango aerobico granulare, in termini di dimensione media dei granuli. In particolare, è stato analizzato l’impatto della differente dimensione dei granuli sul processo di nitrificazione e denitrificazione simultanea (Simultaneous Nitrification Denitrification, SND) e sulla rimozione biologica del fosforo. Allo scopo di valutare l’efficienza di tale tipo di processo, sono state applicate differenti strategie di coltivazione e condizioni operative, in termini di carico organico (COD 600-1200 mg/L) e azoto (60-…

Performance of a MBR pilot plant treating high strenght wastewater: analysis of biomass activity and fouling behaviour

2012

Nowadays, due to the increasing awareness about environmental impact of discharges, it is necessary to realize biological processes that allow complete treatment of wastewater, able to produce high quality effluents that could be used for recycling and reuse purpose. A possible solution to cope with this issue is represented by membrane bioreactors (MBRs), which are combined systems including a bioreactor and a filtration unit. However, in presence of high strenght domestic or industrial wastewater, a modification in biomass kinetics as well as in sludge characteristics may occur. This situation is of importance, since microbial community characteristics can play an important role in membra…

THE USE OF MBR SYSTEMS FOR THE TREATMENT OF REAL SHIPBOARD SLOPS: ANALYSIS OF BIOLOGICAL PERFORMANCE AND BIOMASS BIOKINETIC ACTIVITY

2016

In order to prevent hydrocarbon discharge at sea from ships, the International Maritime Organization (IMO) enacted the MARPOL 73/78 convention in which any oil and oil residue discharged in wastewater streams must contain less than 5 ppm hydrocarbons. Effective treatment of this petroleum-contaminated water is essential prior to its release into the environment, in order to prevent pollution problem for marine ecosystems as well as for human health. The present paper reports the first results of a field gathering campaign aimed at gaining insight about the treatment of real shipboard slops with a MBR pilot plant, in terms of pilot performance and biomass biokinetic activity. The achieved re…

Influence of operative conditions in a hybrid activated sludge/biofilm process for the treatment of municipal wastewater in a cold climate region: a …

2012

In the last years the idea to combine suspended and attached bomass by introducing suspended carriers into the aeration tank for biofilm attachment and growth was proposed. The increase of the overall sludge age in the system leads to a favourable environment for the growth of nitrifying bacteria, so that nitrification may be maintained throughout the winter. The main aim of the study was to investigate a hybrid MBBR process, mostly in terms of nitrification, when operating with different values of the sludge retention time (SRT), and highlighting the influence of temperature on the process. Based on experience in practice it was hypothesized that nitrification could be maintained at far lo…

erformances of a granular sequencing batch reactor (GSBR)

2006

Materie plastiche nei rifiuti. I fabbisogni di energia e di acqua per il recupero: un caso di studio

2005

Submarine outfalls in Sicily: a survey

2004

Reattori a letto mobile ibridi per il trattamento di acque reflue urbane

2008

Biological Approaches to the Treatment of Saline Oily Waste(waters) Originated from Marine Transportation

2012

Oily wastewater generated, in amounts of millions of tons per year, by ships mainly in engine-rooms (bilge waters) and by washing oil tanks (slops) create a major disposal problem throughout the world because of the persistence and accumulation of xenobiotic compounds in the environment. The high salinity levels (up to 25.000 p.p.m.) and the pollutants concentration limit the chances of discharge into the sewer systems and address the disposal of these waste(water)s to the sea. Tightening effluent regulations and consequent high energy and management costs has generated interest in the introduction of biological phases in the treatment of these wastewater. The objectives of this study were …

Trattamenti a membrana per il riutilizzo delle acque reflue nell’industria tessile

2004

I reattori aerobici granulari: esperienze con refluo reale e sintetico

2008

La granulazione aerobica può essere ottenuta nei sistemi con alimentazione discontinua in due differenti configurazioni impiantistiche, che permettono di realizzare i necessari sforzi tangenziali per la formazione dei granuli: il Sequencing Batch Bubble Column Reactor (SBBC) e il Sequencing Batch Airlift Reactor (SBAR). Lo scopo di questo studio è stato quello di osservare il fenomeno della granulazione aerobica e valutare il ruolo del tempo di sedimentazione durante la fase di selezione e formazione dei granuli. L’intera sperimentazione è stata suddivisa in due diverse campagne sperimentali in cui è stato utilizzato refluo sintetico, nella prima, e refluo reale, nella seconda. Al fine di e…

Analisi Sperimentali su impianti MBR ad aerazione intermittente

2014

Monitoring activity to assess the quality conditions of a river: the case study of Oreto, Italy

2004

Influenza dei polimeri extracellulari sul fouling e sul foaming negli impianti MBR.

2009

L’applicazione sempre più diffusa dei bioreattori a membrana presenta tuttavia ancora alcuni fattori limitanti che ne condizionano l’adozione: infatti sono ancora incerte le previsioni della vita utile e dell’efficienza della barriera filtrante. In particolare, notevole incidenza sul processo ha il fouling, causato principalmente dai fenomeni di sporcamento condizionati prevalentemente dalla composizione della sospensione biologica sottoposta a filtrazione. Nella nota sono riportati i risultati di uno studio sperimentale che ha avuto per oggetto l’analisi dell’influenza di alcuni parametri specifici che, oltre a descrivere la qualità del fango attivo dei sistemi MBR, influenzano il processo…

PERFORMANCE OF A MBR PILOT PLANT SUBJECT TO A GRADUAL SALINITY INCREASE: ANALYSIS OF BIOKINETIC AND FOULING BEHAVIOR

2013

Membrane bioreactors (MBRs) have been widely used for the treatment of various wastewater, including municipal, industrial, landfill leachate (Wintgens et al., 2005). Such systems generally provide decisive advantages compared to conventional activated sludge (CAS) processes: in particular, they feature high quality effluent, small footprint and low sludge production rates (Stephenson et al., 2000). In recent years MBRs have also been used for the treatment of specific saline water, such as wastewater produced from shipboard activities, aquaculture wastewater or wastewater deriving by sediment washing treatment, as an example. However, when subject to salinity, a modification of biomass cha…

Characterization of wastewater and biomass activity in a membrane bioreactor using respirometric techniques

2010

Over the last two decades, Membrane Bioreactors (MBRs) emerged even more for wastewater treatment, ensuring high removal efficiencies as well as very small footprint required. Indeed, in this kind of process, a modification in biomass activity and viability can exist compared to that of a conventional activated sludge (CAS) process. In this context, respirometric analysis represents a reliable tool in order to evaluate the actual biomass kinetic parameters, to insert in mathematical models in the design phase, as well as to monitor the biomass viability, especially when these processes are operated with high sludge retention time (SRT) values. The paper presents some results of respirometri…

Capitolo 12 - Interventi per il trattamento delle acque di pioggia

2014

The role of extracellular polymeric substances (EPS) on aerobic granules formation: comparison between a case of synthetic wastewater supply and anot…

2015

The paper focused on the evolution of extracellular polymeric substances (EPSs) content during the granulation process in two Granular Sequencing Batch Airlift Reactors (GSBAR) (3,5 L) fed with synthetic and industrial wastewater. Results showed that EPSs, in particular proteins (PN) were mainly produced during the feast phase because of high substrate availability, especially under conditions of metabolic stress. Than EPSs content reduced during the famine period. More in detail, during the granulation process, a greater polysaccharides (PS) consumption occurred in both reactors, while PN content reduced significantly only in R2. As a result PN/PS ratio increased significantly during granu…

Analisi della fase di start-up di un bioreattore a membrana

2006

L’applicazione dei sistemi MBR, pur garantendo elevati rendimenti di rimozione, è ancora oggi limitata, a causa di alcuni fattori che ne condizionano il funzionamento. Tra questi, uno dei principali è il fouling dovuto ai fenomeni di sporcamento della membrana da parte della sospensione biologica. Nella memoria si riportano i primi risultati di uno studio che ha avuto l’obiettivo di definire l’evoluzione e l’influenza del fouling sul processo di filtrazione durante la fase di avviamento dell’impianto, avvenuto senza inoculo iniziale di fango. La sperimentazione è stata condotta in un impianto pilota costituito da un bioreattore all’interno del quale è stato installato il modulo di membrane …

Insights on mechanisms of excess sludge minimization in an oxic-settling-anaerobic process under different operating conditions and plant configurati…

2022

In the present research, insights about the mechanisms of excess sludge minimization occurring in an oxic-settling-anaerobic (OSA) were provided. The investigation involved two systems operating in parallel. In particular, a conventional activated sludge (CAS) system as control and a system implementing the OSA process both having a pre-denitrification scheme were considered. Five periods (P1-P5) were studied, during which several operating conditions and configurations were tested. Specifically, the hydraulic retention time (HRT) in the anaerobic reactor of the OSA system (P1 8 h, P2-P3 12 h, P4 8 h, P5 12 h) and the return sludge from the anaerobic to the anoxic (scheme A) (P1-P2) or aero…