0000000000018957
AUTHOR
Vicente González
Installation and commissioning of the TileCal Read-Out Drivers
TileCal is the hadronic tile calorimeter of the ATLAS experiment at LHC/CERN. The main component of the TileCal back-end electronics is the Read-Out Driver (ROD). The ROD system is placed between the first and the second level trigger and it is the responsible for processing the data gathered by the detector. The principal devices of the RODs are the Digital Signal Processors (DSPs) mounted in the Processing Units (PUs) daughterboards. The architecture and functionality of the RODs are briefly explained. Then, it is presented the ROD system installation in the ATLAS electronics cavern. Currently, the RODs are being used for the detector commissioning. It is detailed the Detector and Verific…
Measurement of electrons from semileptonic heavy-flavour hadron decays at midrapidity in pp and Pb–Pb collisions at sNN=5.02 TeV
The differential invariant yield as a function of transverse momentum (pT) of electrons from semileptonic heavy-flavour hadron decays was measured at midrapidity in central (0–10%), semi-central (30–50%) and peripheral (60–80%) lead–lead (Pb–Pb) collisions at sNN=5.02 TeV in the pT intervals 0.5–26 GeV/c (0–10% and 30–50%) and 0.5–10 GeV/c (60–80%). The production cross section in proton–proton (pp) collisions at s=5.02 TeV was measured as well in 0.5<pT<10 GeV/c and it lies close to the upper band of perturbative QCD calculation uncertainties up to pT=5 GeV/c and close to the mean value for larger pT. The modification of the electron yield with respect to what is expected for an inco…
ϒ production in p–Pb collisions at sNN=8.16 TeV
$\Upsilon$ production in p-Pb interactions is studied at the centre-of-mass energy per nucleon-nucleon collision $\sqrt{s_{\rm{NN}}}$ = 8.16 TeV with the ALICE detector at the CERN LHC. The measurement is performed reconstructing bottomonium resonances via their dimuon decay channel, in the centre-of-mass rapidity intervals $2.03 < y_{\rm{cms}} < 3.53$ and $-4.46 < y_{\rm{cms}} < -2.96$, down to zero transverse momentum. In this work, results on the inclusive $\Upsilon(1\rm{S})$ production cross section as a function of rapidity and transverse momentum are presented. The corresponding nuclear modification factor shows a suppression of the $\Upsilon(1\rm{S})$ yields with respect to pp collis…
Evaluation of a Commercial PhotoDiode Array for Radiation Detectors Readout
The aim of the present work is the characterization of the new S8866-128-02 PhotoDiode (PD) array from Hamamatsu Photonics. This work includes the implementation of a readout system as well as electronic noise estimation in PDs under several conditions varying integration times and clock frequencies.
D -Meson Azimuthal Anisotropy in Midcentral Pb-Pb Collisions at sNN=5.02 TeV
A.I. Alikhanyan National Science Laboratory (Yerevan Physics Institute) Foundation (ANSL), State Committee of Science and World Federation of Scientists (WFS), Armenia; Austrian Academy of Sciences and Nationalstiftung fur Forschung, Technologie und Entwicklung, Austria; Ministry of Communications and High Technologies, National Nuclear Research Center, Azerbaijan; Conselho Nacional de Desenvolvimento Cientifico e Tecnologico (CNPq), Universidade Federal do Rio Grande do Sul (UFRGS), Financiadora de Estudos e Projetos (Finep), and Fundacao de Amparo a Pesquisa do Estado de Sao Paulo (FAPESP), Brazil; Ministry of Science and Technology of China (MSTC), National Natural Science Foundation of …
ATLAS TileCal Read Out Driver production
The production tests of the 38 ATLAS TileCal Read Out Drivers (RODs) are presented in this paper. The hardware specifications and firmware functionality of the RODs modules, the test-bench and the test procedure to qualify the boards are described. Finally the performance results, the temperature studies and high rate tests are shown and discussed.
The optical instrumentation of the ATLAS Tile Calorimeter
The purpose of this Note is to describe the optical assembly procedure called here Optical Instrumentation and the quality tests conducted on the assembled units. Altogether, 65 Barrel (or LB) modules were constructed - including one spare - together with 129 Extended Barrel (EB) modules (including one spare). The LB modules were mechanically assembled at JINR (Dubna, Russia) and transported to CERN, where the optical instrumentation was performed with personnel contributed by several Institutes. The modules composing one of the two Extended Barrels (known as EBA) were mechanically assembled in the USA, and instrumented in two US locations (ANL, U. of Michigan), while the modules of the oth…
DSP Online Algorithms for The ATLAS TileCal Read-Out Drivers
TileCal is the hadronic tile calorimeter of the ATLAS experiment at LHC/CERN. The central element of the back-end system of the TileCal detector is the read-out driver (ROD).The main components of the TileCal ROD are the digital signal processors (DSPs) placed on the processing unit (PU) daughterboards. This paper presents a detailed description of the code developed for the DSPs. The code is divided into two different parts: the first part contains the core functionalities and the second part the reconstruction algorithms. The core acts as an operating system and controls configuration, data reception and transmission and synchronization between front-end data and the timing, trigger and c…
Functional super Read-Out Driver demonstrator for the Phase II Upgrade of the ATLAS Tile Calorimeter
This work presents the implementation of a functional super Read-Out Driver (sROD) demonstrator for the Phase II Upgrade of the ATLAS Tile Calorimeter (TileCal) in the LHC experiment. The proposed front-end for the Phase II Upgrade communicates with back-end electronics using a multifiber optical connector with a data rate of 57.6 Gbps using the GBT protocol. This functional sROD demonstrator aims to help in the understanding of the problems that could arise in the upgrade of back-end electronics. The demonstrator is composed of three different boards that have been developed in the framework of ATLAS activities: the Optical Multiplexer Board (OMB), the Read-Out Driver (ROD) and the Optical…
Neutron detection and γ-ray suppression using artificial neural networks with the liquid scintillators BC-501A and BC-537
Abstract In this work we present a comparison between the two liquid scintillators BC-501A and BC-537 in terms of their performance regarding the pulse-shape discrimination between neutrons and γ rays. Special emphasis is put on the application of artificial neural networks . The results show a systematically higher γ -ray rejection ratio for BC-501A compared to BC-537 applying the commonly used charge comparison method. Using the artificial neural network approach the discrimination quality was improved to more than 95% rejection efficiency of γ rays over the energy range 150 to 1000 keV for both BC-501A and BC-537. However, due to the larger light output of BC-501A compared to BC-537, neu…
Phantom development for daily checks in electron intraoperative radiotherapy with a mobile linac.
Abstract Purpose IORT with mobile linear accelerators is a well-established modality where the dose rate and, therefore, the dose per pulse are very high. The constancy of the dosimetric parameters of the accelerator has to be checked daily. The aim of this work is to develop a phantom with embedded detectors to improve both accuracy and efficiency in the daily test of an IORT linac at the surgery room. Methods The developed phantom is manufactured with transparent polymethyl methacrylate (PMMA), allocating 6 parallel-plate chambers: a central one to evaluate the on-axis beam output, another on-axis one placed at a fixed depth under the previous one to evaluate the energy constancy and four…
Measurement of the (anti-)3He elliptic flow in Pb–Pb collisions at sNN=5.02TeV
The elliptic flow ( v 2 ) of (anti-) 3He is measured in Pb–Pb collisions at s NN = 5.02 TeV in the transverse-momentum ( p T ) range of 2–6 GeV/c for the centrality classes 0–20%, 20–40%, and 40–60% using the event-plane method. This measurement is compared to that of pions, kaons, and protons at the same center-of-mass energy. A clear mass ordering is observed at low p T , as expected from relativistic hydrodynamics. The violation of the scaling of v 2 with the number of constituent quarks at low p T , already observed for identified hadrons and deuterons at LHC energies, is confirmed also for (anti-) 3He. The elliptic flow of (anti-) 3He is underestimated by the Blast-Wave model and overe…
Testbeam studies of production modules of the ATLAS Tile Calorimeter
We report test beam studies of {11\,\%} of the production ATLAS Tile Calorimeter modules. The modules were equipped with production front-end electronics and all the calibration systems planned for the final detector. The studies used muon, electron and hadron beams ranging in energy from 3~GeV to 350~GeV. Two independent studies showed that the light yield of the calorimeter was $\sim 70$~pe/GeV, exceeding the design goal by {40\,\%}. Electron beams provided a calibration of the modules at the electromagnetic energy scale. Over 200~calorimeter cells the variation of the response was {2.4\,\%}. The linearity with energy was also measured. Muon beams provided an intercalibration of the respo…
Monte Carlo simulation of a single detector unit for the neutron detector array NEDA
WOS: 000301813500009
Effects of one valence proton on seniority and angular momentum of neutrons in neutron-rich Sb51122–131 isotopes
Background: Levels fulfilling the seniority scheme and relevant isomers are commonly observed features in semimagic nuclei; for example, in Sn isotopes (Z=50). Seniority isomers in Sn, with dominantly pure neutron configurations, directly probe the underlying neutron-neutron (νν) interaction. Furthermore, an addition of a valence proton particle or hole, through neutron-proton (νπ) interaction, affects the neutron seniority as well as the angular momentum. Purpose: Benchmark the reproducibility of the experimental observables, like the excitation energies (EX) and the reduced electric-quadrupole transition probabilities [B(E2)], with the results obtained from shell-model interactions for ne…
Conceptual design of the TRACE detector readout using a compact, dead time-less analog memory ASIC
[EN] The new TRacking Array for light Charged particle Ejectiles (TRACE) detector system requires monitorization and sampling of all pulses in a large number of channels with very strict space and power consumption restrictions for the front-end electronics and cabling. Its readout system is to be based on analog memory ASICs with 64 channels each that sample a View the MathML source window of the waveform of any valid pulses at 200 MHz while discarding any other signals and are read out at 50 MHz with external ADC digitization. For this purpose, a new, compact analog memory architecture is described that allows pulse capture with zero dead time in any channel while vastly reducing the tota…
Design of an integrated low-noise, low-power charge sensitive preamplifier for γ and particle spectroscopy with solid state detectors
The design of an integrated charge-sensitive preamplifier suitable for γ-ray spectroscopy is presented. It is fully integrated, except for the feedback resistor, and can drive directly a 50Ω cable with its low impedance output stage. It is designed in AMS 0.35µm technology and its small dimensions and low power consumption (10 mW) are optimized for multi-channel applications. It works both with germanium and silicon detectors for a large range of values of electrode and feedback capacitances. Its wide bandwidth ensures a risetime of 10 ns or less in most configurations. This characteristic makes the preamplifier suitable not only for high resolution spectroscopy but also for pulse-shape ana…
Role of the Δ Resonance in the Population of a Four-Nucleon State in the Fe56→Fe54 Reaction at Relativistic Energies
The 54Fe nucleus was populated from a 56Fe beam impinging on a Be target with an energy of E=A ¼ 500 MeV. The internal decay via γ-ray emission of the 10þ metastable state was observed. As the structure of this isomeric state has to involve at least four unpaired nucleons, it cannot be populated in a simple two-neutron removal reaction from the 56Fe ground state. The isomeric state was produced in the low-momentum (-energy) tail of the parallel momentum (energy) distribution of 54Fe, suggesting that it was populated via the decay of the Δ0 resonance into a proton. This process allows the population of fournucleon states, such as the observed isomer. Therefore, it is concluded that the obser…
Measurement of ϒ(1S) Elliptic Flow at Forward Rapidity in Pb-Pb Collisions at sNN=5.02 TeV
The first measurement of the Υ(1S) elliptic flow coefficient (v2) is performed at forward rapidity (2.5 < y < 4) in Pb–Pb collisions at √sNN=5.02 TeV with the ALICE detector at the LHC. The results are obtained with the scalar product method and are reported as a function of transverse momentum (pT) up to 15 GeV/c in the 5%–60% centrality interval. The measured Υ(1S)v2 is consistent with 0 and with the small positive values predicted by transport models within uncertainties. The v2 coefficient in 2 < pT < 15 GeV/c is lower than that of inclusive J/ψ mesons in the same pT interval by 2.6 standard deviations. These results, combined with earlier suppression measurements, are in agreement with…
Flow dominance and factorization of transverse momentum correlations in Pb-Pb collisions at the LHC
Physical review letters 118(16), 162302 (2017). doi:10.1103/PhysRevLett.118.162302
Cocaine-induced coronary thrombosis and acute myocardial infarction
A 26-year-old man was admitted to our hemodynamic laboratory because of an anterior AMI and post myocardial infarction angina. He is an active smoker (10 cigarettes/day) and consumes inhaled cocaine during weekends (the last consumption of cocaine was 1 week ago). No others risk factors were recorded. Initial electrocardiogram shows sinus rhythm and anterior QS complex (V1–V3) with anterolateral ST segment elevation (V1–V5, D1 and aVL). Creatine-kinase isoenzyme MB and Troponin I were elevated at arrival. Upon admission, the patient was normotensive but with signs of pulmonary congestion. Ventriculography showed anterolateral and apical hypokinesia with an ejection fraction of 21%. Coronari…
Production of charged pions, kaons, and (anti-)protons in Pb-Pb and inelastic pp collisions at sNN=5.02 TeV
Mid-rapidity production of $\pi^{\pm}$, $\rm{K}^{\pm}$ and ($\bar{\rm{p}}$)p measured by the ALICE experiment at the LHC, in Pb-Pb and inelastic pp collisions at $\sqrt{s_{\rm{NN}}}$ = 5.02 TeV, is presented. The invariant yields are measured over a wide transverse momentum ($p_{\rm{T}}$) range from hundreds of MeV/$c$ up to 20 GeV/$c$. The results in Pb-Pb collisions are presented as a function of the collision centrality, in the range 0$-$90%. The comparison of the $p_{\rm{T}}$-integrated particle ratios, i.e. proton-to-pion (p/$\pi$) and kaon-to-pion (K/$\pi$) ratios, with similar measurements in Pb-Pb collisions at $\sqrt{s_{\rm{NN}}}$ = 2.76 TeV show no significant energy dependence. B…
Optical Link Card Design for the Phase II Upgrade of TileCal Experiment
This paper presents the design of an optical link card developed in the frame of the R&D activities for the phase 2 upgrade of the TileCal experiment. This board, that is part of the evaluation of different technologies for the final choice in the next years, is designed as a mezzanine that can work independently or be plugged in the optical multiplexer board of the TileCal backend electronics. It includes two SNAP 12 optical connectors able to transmit and receive up to 75 Gb/s and one SFP optical connector for lower speeds and compatibility with existing hardware as the read out driver. All processing is done in a Stratix II GX field-programmable gate array (FPGA). Details are given on th…
A capacitor selector tool for on-board PDN designs in multigigabit applications
This paper presents a capacitor selector software tool for a proper on-board Power Distribution Network (PDN) design in those high-speed applications which have strict requirements on voltage noise up to the first hundreds of megahertz. Current commercial tools for PDN design only offer a manual choice of the capacitor value and their number simulating the board impedance profile. This manual resolution becomes very hard when the design has high power consumption and noise requirements are very strict. The aim of this software is to solve a basic on-board PDN design minimizing the number of "change simulate-analyze" iterations that have to be carried out in the manual PDN design. This softw…
Pseudorapidity dependence of the anisotropic flow of charged particles in Pb–Pb collisions at sNN=2.76 TeV
We present measurements of the elliptic ($\mathrm{v}_2$), triangular ($\mathrm{v}_3$) and quadrangular ($\mathrm{v}_4$) anisotropic azimuthal flow over a wide range of pseudorapidities ($-3.5< \eta < 5$). The measurements are performed with Pb-Pb collisions at $\sqrt{s_{\text{NN}}} = 2.76$ TeV using the ALICE detector at the Large Hadron Collider (LHC). The flow harmonics are obtained using two- and four-particle correlations from nine different centrality intervals covering central to peripheral collisions. We find that the shape of $\mathrm{v}_n(\eta)$ is largely independent of centrality for the flow harmonics $n=2-4$, however the higher harmonics fall off more steeply with increasing $|…
Algorithms for the ROD DSP of the ATLAS Hadronic Tile Calorimeter
In this paper we present the performance of two algorithms currently running in the Tile Calorimeter Read-Out Driver boards for the commissioning of ATLAS. The first algorithm presented is the so called Optimal Filtering. It reconstructs the deposited energy in the Tile Calorimeter and the arrival time of the data. The second algorithm is the MTag which tags low transverse momentum muons that may escape the ATLAS muon spectrometer first level trigger. Comparisons between online (inside the Read-Out Drivers) and offline implementations are done with an agreement around 99% for the reconstruction of the amplitude using the Optimal Filtering algorithm and a coincidende of 93% between the offli…
Based on Compton Camera
Compton Cameras have been proposed as an alternative to SPECT imaging with Gamma Camera, mainly due to factors such as the electronic collimation, which allows a bigger field of view and provides further information from the acquired events if compared to devices with mechanical collimation. By contrast, this involves a higher amount of data to be processed. In medical devices this leads to waiting times that are generally higher than desirable by the health-care professionals. In this work we have assessed the reconstruction of Compton images by making use of iterative and non-iterative techniques, and also evaluated its performances as a SPECT imaging technique.
Measurement of spin-orbital angular momentum interactions in relativistic heavy-ion collisions
The first evidence of spin alignment of vector mesons ($K^{*0}$ and $\phi$) in heavy-ion collisions at the Large Hadron Collider (LHC) is reported. The spin density matrix element $\rho_{00}$ is measured at midrapidity ($|y| <$ 0.5) in Pb-Pb collisions at a center-of-mass energy ($\sqrt{s_{\rm NN}}$) of 2.76 TeV with the ALICE detector. $\rho_{00}$ values are found to be less than 1/3 (1/3 implies no spin alignment) at low transverse momentum ($p_{\rm T} <$ 2 GeV/$c$) for $K^{*0}$ and $\phi$ at a level of 3$\sigma$ and 2$\sigma$, respectively. No significant spin alignment is observed for the $K^0_S$ meson (spin = 0) in Pb-Pb collisions and for the vector mesons in $pp$ collisions. The meas…
A VLSI for deskewing and fault tolerance in LVDS links
The device presented at this work is a switch implemented in a 0.35 mum CMOS process for compensating the skew which affects parallel data signal transmissions and for providing fault tolerance in large scale scalable systems, for instance used in trigger farms for high energy physics experiments. The SWIFT chip (SWItch for Fault Tolerance) is part of a cluster built around commercially components which has been inspired by the LHCb experiment. The skew is extremely important because it directly affects the sample window available to the receiver logic and either forces to use quality and expensive cables in order to minimize its effects or reduces the maximum signal transmission range or d…
The sROD demonstrator for the ATLAS Tile Calorimeter Upgrade
This work presents the early design of the super Read-Out Driver (sROD) demonstrator board for the Tile Calorimeter Demonstrator project. This project aims to test the new readout electronics architecture for the Phase 2 Upgrade of the ATLAS Tile Calorimeter, replacing the front-end electronics of one complete drawer with the new electronics during the Long Shutdown 2013, in order to evaluate its performance. The sROD demonstrator board will receive and process data from 48 channels. Moreover the sROD demonstrator board will send preprocessed data to the present trigger system, and will transmit trigger control and timing information (TTC) and Detector Control System (DCS) commands to the f…
Scattering Studies with Low-Energy Kaon-Proton Femtoscopy in Proton-Proton Collisions at the LHC
The study of the strength and behaviour of the antikaon-nucleon ($\mathrm{\overline{K}N}$) interaction constitutes one of the key focuses of the strangeness sector in low-energy Quantum Chromodynamics (QCD). In this letter a unique high-precision measurement of the strong interaction between kaons and protons, close and above the kinematic threshold, is presented. The femtoscopic measurements of the correlation function at low pair-frame relative momentum of (K$^+$ p $\oplus$ K$^-$ $\overline{\mathrm{p}}$) and (K$^-$ p $\oplus$ K$^+$ $\overline{\mathrm{p}}$) pairs measured in pp collisions at $\sqrt{s}$ = 5, 7 and 13 TeV are reported. A structure observed around a relative momentum of 58 Me…
First Observation of an Attractive Interaction between a Proton and a Cascade Baryon
Published by the American Physical Society under the terms of the Creative Commons Attribution 4.0 International license. Further distribution of this work must maintain attribution to the author(s) and the published article’s title, journal citation, and DOI. This Letter presents the first experimental observation of the attractive strong interaction between a proton and a multistrange baryon (hyperon) Ξ−. The result is extracted from two-particle correlations of combined p−Ξ−⊕¯p−¯Ξ+ pairs measured in p−Pb collisions at √sNN=5.02 TeV at the LHC with ALICE. The measured correlation function is compared with the prediction obtained assuming only an attractive Coulomb interaction and a stand…
Anisotropic Flow of Charged Particles in Pb-Pb Collisions atsNN=5.02 TeV
We report the first results of elliptic (v2), triangular (v3), and quadrangular (v4) flow of charged particles in Pb-Pb collisions at a center-of-mass energy per nucleon pair of √sNN=5.02 TeV with the ALICE detector at the CERN Large Hadron Collider. The measurements are performed in the central pseudorapidity region |η|<0.8 and for the transverse momentum range 0.2<pT<5 GeV/c. The anisotropic flow is measured using two-particle correlations with a pseudorapidity gap greater than one unit and with the multiparticle cumulant method. Compared to results from Pb-Pb collisions at √sNN=2.76 TeV, the anisotropic flow coefficients v2, v3, and v4 are found to increase by (3.0±0.6)%, (4.3±1.4)%, …
Measuring KS0K± interactions using Pb–Pb collisions at sNN=2.76 TeV
We present the first measurements of femtoscopic correlations between the KS0 and K± particles in pp collisions at s=7 TeV measured by the ALICE experiment. The observed femtoscopic correlations are consistent with final-state interactions proceeding solely via the a0(980) resonance. The extracted kaon source radius and correlation strength parameters for KS0K− are found to be equal within the experimental uncertainties to those for KS0K+ . Results of the present study are compared with those from identical-kaon femtoscopic studies also performed with pp collisions at s=7 TeV by ALICE and with a KS0K± measurement in Pb–Pb collisions at sNN=2.76 TeV. Combined with the Pb–Pb results, our pp a…
Lifetime measurement of neutron-rich even-even molybdenum isotopes
D. Ralet et al. -- 11 pags., 10 figs., 3 tabs.
Lifetime measurements in Ti52,54 to study shell evolution toward N=32
Lifetimes of the excited states in the neutron-rich Ti-52,Ti-54 nuclei, produced in a multinucleon-transfer reaction, were measured by employing the Cologne plunger device and the recoil-distance D ...
A High speed data link optimization for digitalized transfer to processing FPGA
State-of-the-art arrays of detectors, that require digital processing, may have a sizeable number of digitalized signal links. This is the case in several experimental nuclear physics instruments. Moreover, the data rate of the sampled signals, defined primary by the signal bandwidth of the individual detectors, may not exhaust the capabilities of a single FPGA transceiver input. The preprocessing is usually carried out in a modern FPGA with transceiver data rate capabilities over 10Gbps. Moreover, cost effective FPGA have a limited number of transceivers for given FPGA processing capabilities. The investigation of a cost-effective and efficient solution to the mismatch between both data ra…
Pseudorapidity and transverse-momentum distributions of charged particles in proton–proton collisions at s=13 TeV
The pseudorapidity (η) and transverse-momentum (pT) distributions of charged particles produced in proton-proton collisions are measured at the centre-of-mass energy s√ = 13 TeV. The pseudorapidity distribution in |η|< 1.8 is reported for inelastic events and for events with at least one charged particle in | η|< 1. The pseudorapidity density of charged particles produced in the pseudorapidity region |η|< 0.5 is 5.31 ± 0.18 and 6.46 ± 0.19 for the two event classes, respectively. The transverse-momentum distribution of charged particles is measured in the range 0.15 < pT < 20 GeV/c and |η|< 0.8 for events with at least one charged particle in |η|< 1. The correlation between transverse momen…
Multiple register synchronization with a high-speed serial link using the Aurora protocol
In this work, the development and characterization of a multiple synchronous registers interface communicating with a high-speed serial link and using the Aurora protocol is presented. A detailed description of the developing process and the characterization methods and hardware test benches are also included. This interface will implement the slow control busses of the digitizer cards for the second generation of electronics for the Advanced GAmma Tracking Array (AGATA).
Investigation of the p–Σ0 interaction via femtoscopy in pp collisions
This Letter presents the first direct investigation of the p-$\Sigma^{0}$ interaction, using the femtoscopy technique in high-multiplicity pp collisions at $\sqrt{s}$ = 13 TeV measured by the ALICE detector. The $\Sigma^{0}$ is reconstructed via the decay channel to $\Lambda \gamma$, and the subsequent decay of $\Lambda$ to p$\pi^-$. The photon is detected via the conversion in material to e$^{+}$e$^{-}$ pairs exploiting the unique capability of the ALICE detector to measure electrons at low transverse momenta. The measured p-$\Sigma^{0}$ correlation indicates a shallow strong interaction. The comparison of the data to several theoretical predictions obtained employing the $Correlation~Anal…
Signal integrity studies at optical multiplexer board for TileCal system
6 pages.-- ISI Article Identifier: 000253651800006
Development of an optical link card for the upgrade phase II of TileCal experiment
This work presents the design of an optical link card developed in the frame of the R&D activities for the phase 2 upgrade of the TileCal experiment as part of the evaluation of different technologies for the final choice in the next two years. The board is designed as a mezzanine which can work independently or plugged in the Optical Multiplexer Board of the TileCal backend electronics. It includes two SNAP 12 optical connectors able to transmit and receive up to 75 Gbps and one SFP optical connector for lower speeds and compatibility with existing hardware as the Read Out Driver. All processing is done in a Stratix II GX FPGA. Details are given on the hardware design including signal and …
The ATLAS hadronic tile calorimeter: From construction toward-physics
ATLAS; The Tile Calorimeter, which constitutes the central section of the ATLAS hadronic calorimeter, is a non-compensating sampling device made of iron and scintillating tiles. The construction phase of the calorimeter is nearly complete, and most of the effort now is directed toward the final assembly and commissioning in the underground experimental hall. The layout of the calorimeter and the tasks carried out during construction are described, first with a brief reminder of the requirements that drove the calorimeter design. During the last few years a comprehensive test-beam program has been followed in order to establish the calorimeter electromagnetic energy scale, to study its unifo…
Probing the Effects of Strong Electromagnetic Fields with Charge-Dependent Directed Flow in Pb-Pb Collisions at the LHC
The first measurement at the LHC of charge-dependent directed flow ($v_{1}$) relative to the spectator plane is presented for Pb-Pb collisions at $\sqrt{s_{\rm NN}}$ = 5.02 TeV. Results are reported for charged hadrons and $\rm D^{0}$ mesons for the transverse momentum intervals $p_{\rm T}>0.2$ GeV/$c$ and $3<p_{\rm T}<$ 6 GeV/$c$ in the 5-40% and 10-40% centrality classes, respectively. The difference between the positively and negatively charged hadron $v_{1}$ has a positive slope as a function of pseudorapidity $\eta$, ${\rm d}\Delta{v_1}/{\rm d}\eta=$[1.68 $\pm$ 0.49 (stat.) $\pm$ 0.41 (syst.)] $\times 10^{-4}$. The same measurement for $\rm D^{0}$ and $\rm\bar{D}{}^0$ mesons yields a p…
Investigations of Anisotropic Flow Using Multiparticle Azimuthal Correlations in pp , p−Pb , Xe-Xe, and Pb-Pb Collisions at the LHC
Measurements of anisotropic flow coefficients (vn) and their cross-correlations using two- and multiparticle cumulant methods are reported in collisions of pp at √s=13 TeV, p−Pb at a center-of-mass energy per nucleon pair √sNN=5.02 TeV, Xe-Xe at √sNN=5.44 TeV, and Pb-Pb at √sNN=5.02 TeV recorded with the ALICE detector. The multiplicity dependence of vn is studied in a very wide range from 20 to 3000 particles produced in the midrapidity region |η| v3>v4 is found in pp and p−Pb collisions, similar to that seen in large collision systems, while a weak v2 multiplicity dependence is observed relative to nucleus-nucleus collisions in the same multiplicity range. Using a novel subevent method, v…
A New Front-End High-Resolution Sampling Board for the New-Generation Electronics of EXOGAM2 and NEDA Detectors
19th Real Time Conference (RT) -- MAY 26-30, 2014 -- Nara, JAPAN WOS: 000356458000028 This paper presents the final design and results of the FADC Mezzanine for the EXOGAM (EXOtic GAMma array spectrometer) and NEDA (Neutron Detector Array) detectors. The measurements performed include those of studying the effective number of bits, the energy resolution using HP-Ge detectors, as well as timing histograms and discrimination performance. Finally, the conclusion shows how a common digitizing device has been integrated in the experimental environment of two very different detectors which combine both low-noise acquisition and fast sampling rates. Not only the integration fulfilled the expected …
Evaluation of a commercial APD array (Avalanche PhotoDiode) for a readout detector in a hadrontherapy beam characterization application
The aim of the present work is the characterization of the S8898–128–02 Avalanche PhotoDiode array (APDs) from Hamamatsu Photonics. This work includes the implementation of a readout system as well as electronic noise estimation in APDs under several conditions varying integration times and clock frequencies.
Performance of the Fully Digital FPGA-Based Front-End Electronics for the GALILEO Array
In this work we present the architecture and results of a fully digital Front End Electronics (FEE) read out system developed for the GALILEO array. The FEE system, developed in collaboration with the Advanced Gamma Tracking Array (AGATA) collaboration, is composed of three main blocks: preamplifiers, digitizers and preprocessing electronics. The slow control system contains a custom Linux driver, a dynamic library and a server implementing network services. The digital processing of the data from the GALILEO germanium detectors has demonstrated the capability to achieve an energy resolution of 1.53 per mil at an energy of 1.33 MeV.
Digital pulse-timing technique for the neutron detector array NEDA
WOS: 000348040900011
Development of the optical multiplexer board prototype for data acquisition in TileCal experiment
The optical multiplexer board is one of the elements present in the read out chain of the tile calorimeter in ATLAS experiment. Due to radiation effects, two optical fibers with the same data come out from the front end boards to this board, which has to decide in real time which one carries good data and pass them to the read out driver motherboard for processing. This paper describes the design and tests of the first prototype, implemented as a 6U VME64x slave module, including both hardware and firmware aspects. In this last, algorithms for cyclic redundancy code checking are used to make the decision. Besides, the board may be used as a data injector for testing purposes of the read out…
Linear and non-linear flow mode in Pb–Pb collisions at sNN=2.76 TeV
The second and the third order anisotropic flow, V2 and V3, are mostly determined by the corresponding initial spatial anisotropy coefficients, e2 and e3, in the initial density distribution. In addition to their dependence on the same order initial anisotropy coefficient, higher order anisotropic flow, Vn (n > 3), can also have a significant contribution from lower order initial anisotropy coefficients, which leads to mode-coupling effects. In this Letter we investigate the linear and non-linear modes in higher order anisotropic flow Vn for n = 4, 5, 6 with the ALICE detector at the Large Hadron Collider. The measurements are done for particles in the pseudorapidity range |η| < 0.8 and the…
Design of a mezzanine card with bandwidth aggregation for HPGe gamma spectroscopy
In experimental nuclear physics, HPGe segmented detectors are used to provide high energy resolution of the gamma rays. Besides, 4pi configuration is common to get a full coverage of the interaction point and detection of all the products of the collisions. In this type of experiments, the number of electronic channels can be high (>100) and also the sampling frequency of the digitizing system (>100 Msps). This results in a high data rate per channel (> 2 Gbps) and thus a high aggregated bandwidth to process. In principle, this problem can be solved using a parallel data acquisition system where the input channels (commonly arriving through optical fibers) are read and processed accordingly…
Azimuthally Differential Pion Femtoscopy in Pb-Pb Collisions at sNN=2.76 TeV
We present the first azimuthally differential measurements of the pion source size relative to the second harmonic event plane in Pb-Pb collisions at a center-of-mass energy per nucleon-nucleon pair of √sNN = 2.76 TeV. The measurements have been performed in the centrality range 0%-50% and for pion pair transverse momenta 0.2 < kT < 0.7 GeV/c. We find that the Rside and Rout radii, which characterize the pion source size in the directions perpendicular and parallel to the pion transverse momentum, oscillate out of phase, similar to what was observed at the Relativistic Heavy Ion Collider. The final-state source eccentricity, estimated via Rside oscillations, is found to be significantly sma…
Multiplicity dependence of light (anti-)nuclei production in p–Pb collisions at sNN=5.02 TeV
The measurement of the deuteron and anti- deuteron production in the rapidity range −1 < y < 0 as a function of transverse momentum and event multiplicity in p–Pb collisions at √sNN= 5.02 TeV is presented. (Anti-)deuterons are identified via their specific energy loss dE/dxand via their time-of-flight. Their production in p–Pb collisions is compared to pp and Pb–Pb collisions and is discussed within the context of thermal and coalescence models. The ratio of integrated yields of deuterons to protons (d/p) shows a significant increase as a function of the charged-particle multiplicity of the event starting from values similar to those observed in pp collisions at low multiplicities and appro…
Production of 4He and 4He‾ in Pb–Pb collisions at sNN=2.76TeV at the LHC
Results on the production of 4 He and He‾4 nuclei in Pb–Pb collisions at sNN=2.76TeV in the rapidity range |y|<1 , using the ALICE detector, are presented in this paper. The rapidity densities corresponding to 0–10% central events are found to be dN/dyHe4=(0.8±0.4(stat)±0.3(syst))×10−6 and dN/dyHe‾4=(1.1±0.4(stat)±0.2(syst))×10−6 , respectively. This is in agreement with the statistical thermal model expectation assuming the same chemical freeze-out temperature ( Tchem=156MeV ) as for light hadrons. The measured ratio of He‾4/4He is 1.4±0.8(stat)±0.5(syst) .
Pulse pile-up identification and reconstruction for liquid scintillator based neutron detectors
WOS: 000433206800010 The issue of pulse pile-up is frequently encountered in nuclear experiments involving high counting rates, which will distort the pulse shapes and the energy spectra. A digital method of off-line processing of pile-up pulses is presented. The pile-up pulses were firstly identified by detecting the downward-going zero-crossings in the first-order derivative of the original signal, and then the constituent pulses were reconstructed based on comparing the pile-up pulse with four models that are generated by combining pairs of neutron and.. standard pulses together with a controllable time interval. The accuracy of this method in resolving the pile-up events was investigate…
Production of muons from heavy-flavour hadron decays in p–Pb collisions at sNN=5.02 TeV
Abstract The production of muons from heavy-flavour hadron decays in p–Pb collisions at s NN = 5.02 TeV was studied for 2 p T 16 GeV/c with the ALICE detector at the CERN LHC. The measurement was performed at forward (p-going direction) and backward (Pb-going direction) rapidity, in the ranges of rapidity in the centre-of-mass system (cms) 2.03 y cms 3.53 and − 4.46 y cms − 2.96 , respectively. The production cross sections and nuclear modification factors are presented as a function of transverse momentum ( p T ). At forward rapidity, the nuclear modification factor is compatible with unity while at backward rapidity, in the interval 2.5 p T 3.5 GeV/c, it is above unity by more than 2σ. Th…
Exploration of jet substructure using iterative declustering in pp and Pb–Pb collisions at LHC energies
The ALICE collaboration at the CERN LHC reports novel measurements of jet substructure in pp collisions at $\sqrt{s}$= 7 TeV and central Pb-Pb collisions at $\sqrt{s_{\rm{NN}}}$ = 2.76 TeV. Jet substructure of track-based jets is explored via iterative declustering and grooming techniques. We present the measurement of the momentum sharing of two-prong substructure exposed via grooming, the $z_{\rm{g}}$, and its dependence on the opening angle, in both pp and Pb-Pb collisions. We also present the first measurement of the distribution of the number of branches obtained in the iterative declustering of the jet, which is interpreted as the number of its hard splittings. In Pb-Pb collisions, we…
Centrality dependence of the pseudorapidity density distribution for charged particles in Pb–Pb collisions at sNN=2.76 TeV
We present the charged-particle pseudorapidity density in Pb-Pb collisions at $\sqrt{s_{\mathrm{NN}}}=5.02\,\mathrm{Te\kern-.25exV}$ in centrality classes measured by ALICE. The measurement covers a wide pseudorapidity range from $-3.5$ to $5$, which is sufficient for reliable estimates of the total number of charged particles produced in the collisions. For the most central (0-5%) collisions we find $21\,400\pm 1\,300$ while for the most peripheral (80-90%) we find $230\pm 38$. This corresponds to an increase of $(27\pm4)\%$ over the results at $\sqrt{s_{\mathrm{NN}}}=2.76\,\mathrm{Te\kern-.25exV}$ previously reported by ALICE. The energy dependence of the total number of charged particles…
Pairing-quadrupole interplay in the neutron-deficient tin nuclei: First lifetime measurements of low-lying states in 106,108Sn
The lifetimes of the low-lying excited states 2(+) and 4(+) have been directly measured in the neutron-deficient Sn-106,Sn-108 isotopes. the nuclei were populated via a deep-inelastic reaction and the lifetime measurement was performed employing a differential plunger device. the emitted gamma rays were detected by the AGATA array, while the reaction products were uniquely identified by the VAMOS++ magnetic spectrometer. Large-Scale Shell-Model calculations with realistic forces indicate that, independently of the pairing content of the interaction, the quadrupole force is dominant in the B(E2; 2(1)(+) -> 0(g.s)(+)) values and it describes well the experimental pattern for Sn104-114 ; the B…
Fully digital FPGA-based Front-End Electronics for the GALILEO array
In this work we present the fully digital Front End Electronics (FEE) read out system developed for the GALILEO array. The system, developed in collaboration with the Advanced Gamma Tracking Array (AGATA) collaboration, is composed of three main blocks: preamplifiers, digitizers and preprocessing electronics. The slow control system contains a custom Linux driver, a dynamic library and a server implementing network services. The digital processing of the data from the GALILEO germanium detectors has demonstrated the capability to achieve an energy resolution of 1.53‰ at an energy of 1.33 MeV.
Performance of the Advanced GAmma Tracking Array at GANIL
The performance of the Advanced GAmma Tracking Array (AGATA) at GANIL is discussed, on the basis of the analysis of source and in-beam data taken with up to 30 segmented crystals. Data processing is described in detail. The performance of individual detectors are shown. The efficiency of the individual detectors as well as the efficiency after $\gamma$-ray tracking are discussed. Recent developments of $\gamma$-ray tracking are also presented. The experimentally achieved peak-to-total is compared with simulations showing the impact of back-scattered $\gamma$ rays on the peak-to-total in a $\gamma$-ray tracking array. An estimate of the achieved position resolution using the Doppler broadeni…
Isospin dependence of electromagnetic transition strengths among an isobaric triplet
*Aydın, Sezgin ( Aksaray, Yazar )
Multi-strange baryon production in p Pb collisions at sNN=5.02 TeV
The multi-strange baryon yields in Pb--Pb collisions have been shown to exhibit an enhancement relative to pp reactions. In this work, $\Xi$ and $\Omega$ production rates have been measured with the ALICE experiment as a function of transverse momentum, ${p_{\rm T}}$, in p-Pb collisions at a centre-of-mass energy of ${\sqrt{s_{\rm NN}}}$ = 5.02 TeV. The results cover the kinematic ranges 0.6 GeV/$c<{p_{\rm T}} <$7.2 GeV/$c$ and 0.8 GeV/$c<{p_{\rm T}}<$ 5 GeV/$c$, for $\Xi$ and $\Omega$ respectively, in the common rapidity interval -0.5 $<{y_{\rm CMS}}<$ 0. Multi-strange baryons have been identified by reconstructing their weak decays into charged particles. The ${p_{\rm T}}$ spectra are ana…
Estrategia invasiva en pacientes con diabetes avanzada y síndrome coronario agudo sin elevación del segmento ST. Hallazgos angiográficos y evolución clínica. Resultados del estudio PREDICAR
Introduccion y objetivos La diabetes avanzada se puede asociar con una enfermedad coronaria difusa de dificil revascularizacion. Se estudiaron los hallazgos angiograficos y la evolucion clinica de pacientes con diabetes avanzada (insulinodependencia o mas de 5 anos con farmacos) y sindrome coronario agudo sin elevacion del segmento ST tratados con estrategia invasiva. Metodos Se incluyo a 141 pacientes. En la coronariografia se cuantifico la extension de la enfermedad coronaria mediante un sistema de puntuacion sobre 29 segmentos. Durante 1 ano se recogio el evento combinado de muerte, infarto o reingreso por angina. Resultados La extension de la enfermedad coronaria se asocio con 4 variabl…
The Optical Multiplexer Board for the ATLAS Hadronic Tile Calorimeter
This paper presents the architecture and the status of the optical multiplexer board (OMB) for the ATLAS/LHC tile hadronic calorimeter (TileCal). This board will analyze the front-end data CRC to prevent bit and burst errors produced by radiation. Besides, due to its position within the data acquisition chain it will be used to emulate front-end data for tests. The first two prototypes of the final OMB 9U version have been produced at CERN. Detailed design issues and manufacturing features of these prototypes are described. These prototypes are being validated while firmware developments are being implemented in the programmable devices of the board.
Development of the Optical Multiplexer Board Prototype for Data Acquisition in the TileCal System
This paper describes the development of the optical multiplexer board (OMB), also known as PreROD board, for the TileCal readout system in the ATLAS experiment. The aim of this board is to overcome the problems that may arise in the integrity of data due to radiation effects. The solution adopted has been to add redundancy to data transmission and so two optical fibers with the same data come out from the detector front end boards. The OMB has to decide in real time which fiber, eventually, carries data with no errors switching it to the output link connected to the read out driver (ROD) motherboard where data processing takes place. Besides, the board may be also used as a data injector fo…
Centrality Dependence of the Charged-Particle Multiplicity Density at Midrapidity in Pb-Pb Collisions atsNN=5.02 TeV
The pseudorapidity density of charged particles, dNch/dη, at midrapidity in Pb-Pb collisions has been measured at a center-of-mass energy per nucleon pair of √sNN=5.02 TeV. For the 5% most central collisions, we measure a value of 1943 ± 54. The rise in dNch/dη as a function of √sNN p is steeper than that observed in proton-proton collisions and follows the trend established by measurements at lower energy. The increase of dNch/dη as a function of the average number of participant nucleons, ⟨Npart⟩, calculated in a Glauber model, is compared with the previous measurement at √sNN=2.76 TeV. A constant factor of about 1.2 describes the increase in dNch/dη from √sNN=2.76 to 5.02 TeV for all cen…
Graphical user interface for serial protocols through a USB link
In this work, a graphical user interface to communicate with three common serial protocols is presented. With one tool, the user may be able to control several evaluation boards from different manufacturers or evaluate and program integrated circuits of complex board prototypes. It provides a user-friendly interface to communicate with several chips using the USB port. The program has been used for the first stages in the qualification process of electronic boards for the Advanced GAmma Tracking Array (AGATA).
Azimuthal anisotropy of charged jet production in sNN=2.76 TeV Pb–Pb collisions
We present measurements of the azimuthal dependence of charged jet production in central and semicentral √sNN = 2.76 TeV Pb–Pb collisions with respect to the second harmonic event plane, quantified as vch jet 2 . Jet finding is performed employing the anti-kT algorithm with a resolution parameter R = 0.2 using charged tracks from the ALICE tracking system. The contribution of the azimuthal anisotropy of the underlying event is taken into account event-by-event. The remaining (statistical) region-to-region fluctuations are removed on an ensemble basis by unfolding the jet spectra for different event plane orientations independently. Significant non-zero vch jet 2 is observed in semi-central …
Determination of the event collision time with the ALICE detector at the LHC
The European physical journal / Plus 132(2), 99 (2017). doi:10.1140/epjp/i2017-11279-1
Basic Concepts of Power Distribution Network Design for High-Speed Transmission
This paper tries to gather the Power Distribution Network (PDN) techniques used to preserve power integrity in PCB designs when transmitting data rates over 6 Gbps using the newest commercial optical modules. The PDN design described allows for proper impedance control of the power supply with the appropriate choice of the number, location and values of capacitors. This method needs the knowledge of the electrical RLC model of the regulators, copper planes, capacitors and vias used in the PCB. A particular case of PDN design will be presented for a module using one SNAP12 optical transmitter and one receiver connected to an Altera Stratix II GX FPGA. This board is designed to work with data…
Measurement of pion and proton response and longitudinal shower profiles up to 20 nuclear interaction lengths with the ATLAS Tile calorimeter
The response of pions and protons in the energy range of 20–180 GeV, produced at CERN's SPS H8 test-beam line in the ATLAS iron–scintillator Tile hadron calorimeter, has been measured. The test-beam configuration allowed the measurement of the longitudinal shower development for pions and protons up to 20 nuclear interaction lengths. It was found that pions penetrate deeper in the calorimeter than protons. However, protons induce showers that are wider laterally to the direction of the impinging particle. Including the measured total energy response, the pion-to-proton energy ratio and the resolution, all observations are consistent with a higher electromagnetic energy fraction in pion-indu…
Invasive Strategy in Patients With Advanced Diabetes and Non-ST-Segment Elevation Acute Coronary Syndrome. Angiographic Findings and Clinical Follow-Up. PREDICAR Study Results
Introduction and objectives Advanced diabetes can be associated with diffuse coronary artery disease that is difficult to treat by revascularization. We studied angiographic findings and disease progression in patients with advanced diabetes (either insulin-dependent or taking antidiabetic drugs for >5 years) and non-ST-elevation acute coronary syndrome who were being treated using an invasive strategy. Methods The study included 141 patients. The extent of the coronary artery disease was quantified using a score derived from a 29-segment coronary angiogram. The composite endpoint was death, myocardial infarction, or readmission for unstable angina within one year of follow-up. Results The …
Optimal filtering algorithm implementation in FPGAs for the ATLAS TileCal Read-Out drivers
TileCal is the hadronic calorimeter of the ATLAS experiment in the LHC (CERN). Its Read-Out Drivers (RODs) process, in real time, the digitized information coming from the front-end electronics and send it to the Read-Out System. Data processing in the ROD boards is performed in Processing Unit Mezzanine Cards that use commercial DSPs to run the Optimal Filtering (OF) algorithms.
Development of the control card for the digitizers of the second generation electronics of AGATA
In this work, the features and development process of the novel control card for the digitizers of AGATA are presented. The board is part of the new hardware proposed for the electronic system of the experiment. In particular, the control card provides the sampling clock for the digitizers, contributes to the synchronization of the digital data and performs the slow control of its associated digitizer cards.
Multiplicity dependence of charged pion, kaon, and (anti)proton production at large transverse momentum in p–Pb collisions at sNN=5.02 TeV
The production of charged pions, kaons and (anti)protons has been measured at mid-rapidity ($-0.5 10$ GeV/$c$), the particle ratios are consistent with those reported for pp and Pb-Pb collisions at the LHC energies. At intermediate $p_{\rm T}$ the (anti)proton $R_{\rm pPb}$ shows a Cronin-like enhancement, while pions and kaons show little or no nuclear modification. At high $p_{\rm T}$ the charged pion, kaon and (anti)proton $R_{\rm pPb}$ are consistent with unity within statistical and systematic uncertainties.
Longitudinal and azimuthal evolution of two-particle transverse momentum correlations in Pb–Pb collisions at sNN=2.76TeV
This paper presents the first measurements of the charge independent (CI) and charge dependent (CD) two-particle transverse momentum correlators G2CI and G2CD in Pb–Pb collisions at sNN=2.76TeV by the ALICE collaboration. The two-particle transverse momentum correlator G2 was introduced as a measure of the momentum current transfer between neighboring system cells. The correlators are measured as a function of pair separation in pseudorapidity (Δη) and azimuth (Δφ) and as a function of collision centrality. From peripheral to central collisions, the correlator G2CI exhibits a longitudinal broadening while undergoing a monotonic azimuthal narrowing. By contrast, G2CD exhibits a narrowing alo…
Test of digital neutron-gamma discrimination with four different photomultiplier tubes for the NEutron Detector Array (NEDA)
WOS: 000344994600012
Centrality evolution of the charged-particle pseudorapidity density over a broad pseudorapidity range in Pb–Pb collisions at sNN=2.76 TeV
State Committee of Science, World Federation of Scientists (WFS) and Swiss Fonds Kidagan, Armenia; Conselho Nacional de Desenvolvimento Cientifico e Tecnologico (CNPq), Financiadora de Estudos e Projetos (FINEP), Fundacao de Amparo a Pesquisa do Estado de Sao Paulo (FAPESP); National Natural Science Foundation of China (NSFC), the Chinese Ministry of Education (CMOE) and the Ministry of Science and Technology of China (MSTC); Ministry of Education and Youth of the Czech Republic; Danish Natural Science Research Council, the Carlsberg Foundation and the Danish National Research Foundation; The European Research Council under the European Community's Seventh Framework Programme; Helsinki Inst…
Measurement of an Excess in the Yield ofJ/ψat Very LowpTin Pb–Pb Collisions atsNN=2.76 TeV
We report on the first measurement of an excess in the yield of J/ψ at very low transverse momentum (pT< 0.3 GeV/c) in peripheral hadronic Pb-Pb collisions at √sNN = 2.76 TeV, performed by ALICE at the CERN LHC. Remarkably, the measured nuclear modification factor of J/ψ in the rapidity range 2.5< y< 4 reaches about 7 (2) in the pT range 0- 0.3 GeV/c in the 70-90% (50-70%) centrality class. The J/ψ production cross section associated with the observed excess is obtained under the hypothesis that coherent photoproduction of J/ψ is the underlying physics mechanism. If confirmed, the observation of J/ψ coherent photoproduction in Pb-Pb collisions at impact parameters smaller than twice the nuc…
Measurements of inclusive jet spectra in pp and central Pb-Pb collisions at sNN=5.02TeV
This article reports measurements of the pT- differential inclusive jet cross section in pp collisions at √s=5 .02TeV and the pT- differential inclusive jet yield in Pb-Pb 0–10% central collisions at√sNN =5.02TeV. Jets were reconstructed at midrapidity with the ALICE tracking detectors and electromagnetic calorimeter using the anti-kT algorithm. For ppcollisions, we report jet cross sections for jet resolution parameters R =0.1–0.6 over the range 20 < pT, jet < 140 GeV/c, as well as the jet cross-section ratios of different R and comparisons to two next-to-leading-order (NLO)– based theoretical predictions. For Pb-Pb collisions, we report the R=0.2 and R=0.4 jet spectra for 40 < pT, jet < 1…
Mechanical construction and installation of the ATLAS tile calorimeter
This paper summarises the mechanical construction andinstallation of the Tile Calorimeter for the ATLASexperiment at the Large Hadron Collider in CERN, Switzerland. The TileCalorimeter is a sampling calorimeter using scintillator as the sensitivedetector and steel as the absorber and covers the central region of the ATLASexperiment up to pseudorapidities ±1.7. The mechanical construction ofthe Tile Calorimeter occurred over a periodof about 10 years beginning in 1995 with the completionof the Technical Design Report and ending in 2006 with the installationof the final module in the ATLAS cavern. Duringthis period approximately 2600 metric tons of steel were transformedinto a laminated struc…
Low-lying electric dipole gamma-continuum for the unstable Fe-62,64 nuclei : Strength evolution with neutron number
6 pags., 4 figs.
The ATLAS tile calorimeter ROD injector and multiplexer board
Abstract The ATLAS Tile Calorimeter is a sampling detector composed by cells made of iron-scintillator tiles. The calorimeter cell signals are digitized in the front-end electronics and transmitted to the Read-Out Drivers (RODs) at the first level trigger rate. The ROD receives triggered data from up to 9856 channels and provides the energy, phase and quality factor of the signals to the second level trigger. The back-end electronics is divided into four partitions containing eight RODs each. Therefore, a total of 32 RODs are used to process and transmit the data of the TileCal detector. In order to emulate the detector signals in the production and commissioning of ROD modules a board call…
Correlated Event-by-Event Fluctuations of Flow Harmonics in Pb-Pb Collisions at sNN=2.76 TeV
We report the measurements of correlations between event-by-event fluctuations of amplitudes of anisotropic flow harmonics in nucleus-nucleus collisions, obtained for the first time using a new analysis method based on multiparticle cumulants in mixed harmonics. This novel method is robust against systematic biases originating from non-flow effects and by construction any dependence on symmetry planes is eliminated. We demonstrate that correlations of flow harmonics exhibit a better sensitivity to medium properties than the individual flow harmonics. The new measurements are performed in Pb-Pb collisions at the centre-of-mass energy per nucleon pair of $\sqrt{s_{_{\rm NN}}}=2.76$ TeV by the…
Multiplicity dependence of K*(892)0 and ϕ(1020) production in pp collisions at s=13 TeV
The striking similarities that have been observed between high-multiplicity proton-proton (pp) collisions and heavy-ion collisions can be explored through multiplicity-differential measurements of identified hadrons in pp collisions. With these measurements, it is possible to study mechanisms such as collective flow that determine the shapes of hadron transverse momentum ( pT ) spectra, to search for possible modifications of the yields of short-lived hadronic resonances due to scattering effects in an extended hadron-gas phase, and to investigate different explanations provided by phenomenological models for enhancement of strangeness production with increasing multiplicity. In this paper,…
Particle identification in ALICE: a Bayesian approach
We present a Bayesian approach to particle identification (PID) within the ALICE experiment. The aim is to more effectively combine the particle identification capabilities of its various detectors. After a brief explanation of the adopted methodology and formalism, the performance of the Bayesian PID approach for charged pions, kaons and protons in the central barrel of ALICE is studied. PID is performed via measurements of specific energy loss ($\mathrm{d}E/\mathrm{d}x$) and time-of-flight. PID efficiencies and misidentification probabilities are extracted and compared with Monte Carlo simulations using high-purity samples of identified particles in the decay channels ${\rm K}^0_S \righta…
Maximum Likelihood Estimation and non-linear least squares fitting with Levenberg-Marquardt Algorithm implementation in FPGA devices for high resolution hodoscopy
This work compares two possible solutions to achieve a higher resolution in a hodoscope based on Plastic Scintillating Fibers (PSF) by obtaining the point of maximum incidence of the radioactive beam. The two fitting algorithms proposed have been tested and implemented in Field Programmable Gate Array (FPGA) devices. On one hand, a probabilistic model based on the Maximum Likelihood Estimation (MLE) and on the other hand, non-linear least-squares fit with the Levenberg-Marquardt Algorithm (LMA).
Study of isomeric states in $^{198,200,202,206}$Pb and $^{206}$Hg populated in fragmentation reactions
International audience; Isomeric states in isotopes in the vicinity of doubly-magic 208Pb were populatedfollowing reactions of a relativistic 208Pb primary beam impinging on a9Be fragmentation target. Secondary beams of 198,200,202,206Pb and 206Hg wereisotopically separated and implanted in a passive stopper positioned in thefocal plane of the GSI Fragment Separator. Delayed γ rays were detected withthe Advanced Gamma Tracking Array (AGATA). Decay schemes were reevaluatedand interpreted with shell-model calculations. The momentumdependentpopulation of isomeric states in the two-nucleon hole nuclei206Pb/206Hg was found to differ from the population of multi neutron-holeisomeric states in 198…
Study and simulation of the read-out electronics design for a high-resolution plastic scintillating fiber based hodoscope
Abstract This work presents the study and simulation of a high-resolution charged particle detection device for beam positioning, monitoring and calibration, together with its read-out proposal. To provide the precise positional information of the beam, the detection system has been based on Plastic Scintillating Fibers (PSF), while the read-out on a Silicon-PhotoDiode (Si-PD) array. To carry out the study, a PSF prototype with one detection plane has been experimentally tested with a β particle source. Besides, Monte Carlo simulations of the complete system have also been conducted. Both simulations and experimental tests give consistency to the results obtained. The work presented in this…
Slackline Training in Children with Spastic Cerebral Palsy: A Randomized Clinical Trial
Objective: To assess whether a slackline intervention program improves postural control in children/adolescents with spastic cerebral palsy (CP). Design: Randomized controlled trial. Setting: Patients&rsquo
A new preprocessing and control board for the phase 2 electronics of AGATA experiment
The electronics of AGATA HPGe segmented gamma ray detector faces a new challenge in the search of a bigger integration and cost reduction for the phase 2 of the experiment going beyond 45 crystals. This opportunity can be used to introduce a new architecture based on commercial standards while keeping backward compatibility with current electronics. In this sense, new FPGA devices and fast Ethernet links can be used to ease the preprocessing and control task and allowing for processor farms to distribute the processing load. At the same time, modularity should be a key feature of the design in the aim to make it upgradable in time and technology. This paper presents the design of a new prep…
AGATA-Advanced GAmma Tracking Array
WOS: 000300864200005
Isospin Properties of Nuclear Pair Correlations from the Level Structure of the Self-Conjugate Nucleus Ru88
The low-lying energy spectrum of the extremely neutron-deficient self-conjugate (N = Z) nuclide 88 44Ru44 has been measured using the combination of the Advanced Gamma Tracking Array (AGATA) spectrometer, the NEDA and Neutron Wall neutron detector arrays, and the DIAMANT charged particle detector array. Excited states in 88Ru were populated via the 54Fe(36Ar; 2n )88Ru fusion-evaporation reaction at the Grand Acc�el�erateur National d'Ions Lourds (GANIL) accelerator complex. The observed -ray cascade is assigned to 88Ru using clean prompt - -2-neutron coincidences in anti-coincidence with the detection of charged particles, con�rming and extending the previously assigned sequence of low-lyin…
J/ production as a function of charged-particle pseudorapidity density in p–Pb collisions at
We report measurements of the inclusive J/ψ yield and average transverse momentum as a function of charged-particle pseudorapidity density dNch/dη in p–Pb collisions at sNN=5.02TeV with ALICE at the LHC. The observables are normalised to their corresponding averages in non-single diffractive events. An increase of the normalised J/ψ yield with normalised dNch/dη, measured at mid-rapidity, is observed at mid-rapidity and backward rapidity. At forward rapidity, a saturation of the relative yield is observed for high charged-particle multiplicities. The normalised average transverse momentum at forward and backward rapidities increases with multiplicity at low multiplicities and saturates beyo…
Global baryon number conservation encoded in net-proton fluctuations measured in Pb–Pb collisions at sNN=2.76 TeV
Experimental results are presented on event-by-event net-proton fluctuation measurements in Pb–Pb collisions at sNN=2.76 TeV, recorded by the ALICE detector at the CERN LHC. These measurements have as their ultimate goal an experimental test of Lattice QCD (LQCD) predictions on second and higher order cumulants of net-baryon distributions to search for critical behavior near the QCD phase boundary. Before confronting them with LQCD predictions, account has to be taken of correlations stemming from baryon number conservation as well as fluctuations of participating nucleons. Both effects influence the experimental measurements and are usually not considered in theoretical calculations. For t…