PPG embedded system for blood pressure monitoring

In this work, we have designed and implemented a microcontroller-based embedded system for blood pressure monitoring through a PhotoPlethysmoGraphic (PPG) technique. In our system, it is possible to perform PPG measurements via reflectance mode. Hardware novelty of our system consists in the adoption of Silicon PhotoMultiplier detectors. The signal received from the photodetector is used to calculate the instantaneous heart rate and therefore the heart rate variability. The obtained results show that, by using our system, it is possible to easily extract both the PPG and the breath signal. These signals can be used to monitor the patients during the convalescence both in hospital and at hom…

Random Quasi-Phae-Matching in Tantalatio di Litio: origine del fenomeno, confronto tra propagazione bulk e guidata.

We observe second harmonic generation via random quasi phase matching in a 1.5μm periodically poled lithium tantalate. The presence of a slab waveguides allows the comparison between bulk and guided wave configurations.

Rateless codes mitigation technique in a turbulent indoor Free Space Optics link

Free Space Optics (FSO) links are affected by several impairments and, among them, optical turbulence is the most important factor that can degrade the link quality. Due to the presence of this phenomenon, the signal irradiance detected by the receiver fluctuates, thus causing erasure errors and fading events. In this work, we present an indoor Free Space Optics link, in which several turbulence conditions are generated by using two heating elements. We show that the generated turbulence causes erasure errors and packet losses during the data transmission, and we also compare the statistical distribution of the samples with the theoretical models. Moreover, we demonstrate how the applicatio…

Photoelectric valuation of highly efficient Dye-Sensitized Solar Cells

Nowadays, a growing demand for free and clean energy requires the study and the development of new low-cost solar photovoltaic (PV) cells. Among them, Dye Sensitized Solar Cells (DSSCs) based on ruthenium complexes as sensitizers are assuming a great importance. The DSSCs under study are composed placing in succession a transparent conductive glass on which is screen-printed a mesoporous TiO2 thin film sensitized by a ruthenium based dye (N719) , an electrolytic solution containing a redox couple (I-/I3-) and another conductive glass covered by a thin transparent catalyst platinum film. In this work, we have measured the main photoelectrochemical parameters of the above mentioned DSSCs at d…

P-on-N and N-on-P silicon photomultipliers: responsivity comparison in the continuous wave regime

We report the electrical and optical comparison, in continuous wave regime, of two novel classes of silicon photomultipliers (SiPMs) fabricated on silicon P-type and N-type substrate respectively. Responsivity measurements have been performed with an incident optical power from tenths of picowatts to hundreds of nanowatts and on a broad spectrum, ranging from ultraviolet to near infrared (340-820 nm). For both classes of investigated SiPMs, responsivity shows flat response versus the optical incident power, when a preset overvoltage and wavelength is applied . More in detail, this linear behavior extends up to about 10 nW for lower overvoltages, while a shrink is observed when the reverse b…

Design of a portable (CW) fNIRS embedded system

HYDROGELS WITH ORDER POROSITY AT THE MESO-SCALE FOR SENSING

Renewable energy evaluation in Italy and Brazil

The aim of this study is a comparison among Italian and Brazilian electrical energy system with a particular focus on renewable energy sources. The energy sector has a key role in the sustainable development of a country, so it influences economic and political choices. The work would underline differences, common point among two country, specially, in this particular socio-economic period and it should emphasize that green economy could be a possible answer to the financial crisis. The work will be divided into four sections: Section I will introduce all details of the question; Section II will explain the renewable assessments for the countries, Section III will talks how renewable energy…

Fabrication and Characterization of Dye-Sensitized Solar Cells

Among the next-generation solar cells, a predominant role is played by Dye sensitized solar cells (DSSC) based on ruthenium complexes as sensitizers. They take advantage of a photoelectrochemical system to transform solar radiation into electric energy. In fact, DSSCs represent a cost-effective alternative to traditional silicon-based photovoltaic devices and they do not require expensive and sophisticated apparatus for their fabrication. In this work, we have produced and tested ruthenium DSSCs. In particular, we have measured the main parameters of these cells, such as the electrical and power performances and the efficiency levels, at different irradiance levels and at different incident…

Time Of Flight measurements via two LiDAR systems with SiPM and APD

In this paper, we present an experimental comparison of two LiDAR systems, employing the SiPM and the APD as photodetectors, in terms of TOF measurements differing for the distance of the target and at different intensities of ambient light. The use of the APD represents the conventional approach, while the implementation of the SiPM is innovative. The performed measurements achieved very promising results, thus demonstrating the effectiveness of our LiDAR based on SiPM.

Fabrication and electro-optical characterization of Ruthenium-based Dye-Sensitized Solar Cells

In this paper, we measure the main photoelectrical parameters of Dye Sensitized Solar Cells (DSSCs) based on ruthenium complexes at different irradiance levels, incident wavelengths, temperatures and hours of light soaking

Città di villeggiatura a Santa Cesarea Terme (LE)

Progetto di masterplan per una piccola città di villegiatura a Santa Cesarea Terme (Le)CONCEPT DEL PIANO 1 Città di villeggiatura e commistione funzionale (Il programma funzionale) 2 Elementi di fondazione: “infrastrutture leggere” (Il viale e il tratturo) 3 Ricostruzione del paesaggio: strategia delle tipologie di vegetazione (Il paesaggio) 4 Integrazione nella rete delle strade esistenti (Le infrastrutture) 5 Intreccio tra spazi urbani e spazi della campagna (Gli spazi ed edifici pubblici/comuni) 6 Tracciati esistenti e nuovi tracciati regolatori (I muri, i recinti, le colture e le regole di impianto) / Uso variabile della densità (Le densità alta, media, bassa) 7 Gradualità dei microclim…

CulnSe2/Zn(S,O,OH) junction on Mo foil by electrochemical and chemical route for photovoltaic applications

Electrodeposition is a convenient technique for the development of low cost materials for photovoltaic (PV) device processing. Using a single step electrodeposition route, several groups have fabricated CIS (CuInSe) and CIGS (CuInGaSe) films [1]. One of the most important requirements for successful application of one-step electrodeposition film formation, is the ability to control composition of the deposited films and to develop polycrystalline microstructures with a low surface roughness and high sintered density. In this preliminary work, CIS films were produced by single bath electrodeposition finding the optimal conditions in order to achieve a dense film with high crystallinity and u…

Responsivity measurements of SiC photodiodes

We investigated the technical features of three novel classes of 4H-SiC vertical Schottky UV photodiodes (henceforth, named SiC8, SiC10, SiC20) employing Ni2Si interdigitated strips whose pitch size is 8, 10 and 20 µm respectively [1] and based on the pinch-off surface effect.

Characterization of Ruthenium-based Dye-Sensitized solar cells

In this paper, we measure the main photoelectrical parameters of Dye Sensitized Solar Cells (DSSCs) based on ruthenium complexes at different irradiance levels, incident wavelengths, temperatures and hours of light soaking.

Non-uniform doping concentration CIGS absorber profile for highefficiency solar cells

The quaternary chalcopyrite semiconductor alloy Cu(In,Ga)Se2 (CIGS) is nowadays commonly considered one of the most suitable materials to fabricate cost-effective and high-efficiency photovoltaic cells. Thanks to the optical and structural properties of the absorber layer and to the tunable bandgap, thin-film CIGS cells have reached efficiencies around 20%, not far from the maximum values of traditional crystalline silicon cells. This high efficiency, together with the conceivable low fabrication costs, makes CIGS cells a promising alternative to silicon technology for large-scale production. In order to further improve the cells performance, in a previous work we have already proposed a si…

THE SILICON PHOTOMULTIPLIER:AN IN-DEPTH ANALYSIS IN THE CONTINUOUS WAVE REGIME

The Silicon Photomultiplier (SiPM) is a novel solid state photon counting detector consisting of a parallel array of avalanche photodiodes biased beyond their breakdown voltage. It has known a fast development in the last few years as a possible alternative to vacuum photomultiplier tubes (PMTs) and conventional avalanche photodiodes (APDs). Indeed, current research in photodetectors is directed toward an increasing miniaturization of the pixel size, thus both improving the spatial resolution and reducing the device dimensions. SiPMs show high photon detection efficiency in the visible and near infrared range, low power consumption, high gain, ruggedness, compact size, excellent single-phot…

Numerical analysis of light soaking phenomenon in Ruthenium based Dye Sensitized Solar Cells

Dye Sensitized Solar Cells (DSSCs) are widely considered one of the most promising third generation photovoltaic devices, especially thanks to their relatively low cost if compared to conventional solar cells. An interesting phenomenon affecting such devices is the so-called light soaking effect, consisting in the increase of cell main electrical parameters after the exposition to solar light. In this work, starting from the experimental characterization carried out on Ruthenium-based DSSCs, we report on a series of numerical analysis performed to better describe the above-mentioned light soaking effect in order to show the relationship between such phenomenon and the main physical paramete…

Experimental Investigation on the Performances of Innovative PV Vertical Structures

The sustainable development of our planet is considerably related to a relevant reduction of CO2 global emissions, with building consumption contributing more than 40%. In this scenario, new technological conceptions, such as building-integrated photovoltaic technology, emerged in order to satisfy the requirements of sustainability imposed by the European Union. Therefore, the aim of this work is to provide a technical and economical comparison of the performances of different vertical-mounted innovative photovoltaic systems, potentially integrated on a building instead of on traditional windows or glass walls. The proposed investigation was carried out by means of experimental tests on thr…

Signal to noise ratio measurements of silicon photomultipliers in the continuous wave regime

We report on our signal to noise ratio (SNR) measurements carried out, in the continuous wave regime, on a novel class of silicon photomultipliers (SiPMs) fabricated in planar technology on silicon p-type substrate.

Ethanol vapor optical sensors based on polystyrene opals infiltrated with hydrogel

Electrochemical and chemical synthesis of CIS/Zn(S,O,OH) for thin film solar cells

In this work, we are reporting results on the electrodeposition of the CuInSe2 thin films on molybdenum thin foil substrates. We have used an aqueous non-buffered electrolyte and a careful choice of deposition parameters to ensure a good quality and composition of the deposited films. In addition, CdS was replaced in the buffer layer with a wider bandgap Zn(S,O,OH) film obtained by chemical bath deposition. The deposited films were annealed in inert atmosphere at different temperatures. The influence of annealing temperature on the properties of the films is briefly discussed. Films were also characterized by photoelectrochemical and I-V measurements. Structural characterization was carried…

N-on-P and P-on-N Silicon Photomultipliers: Responsivity comparison in the continuous wave regime

We report on the electrical and optical comparison, in continuous wave regime, of two novel classes of silicon photomultipliers fabricated in planar technology on silicon P-type and Ntype substrate respectively. A physical explanation of the experimental results is provided.

Signal to noise ratio measurements of silicon photomultipliers

We report on our signal to noise ratio (SNR) measurements carried out, in the continuous wave regime, on a novel class of silicon photomultipliers (SiPMs) fabricated in planar technology on silicon p-type substrate. SiPMs are large area detectors consisting of a parallel array of Geiger Mode APDs with individual integrated quenching resistors. Each photodiode is an independent photon counting microcell and is connected to a common analog output to produce a summation signal proportional to the number of detected photons [1], [2]. SNR of SiPMs is expressed by the ratio of the SiPM average signal current and the RMS deviation of the overall current (i.e., the overall shot noise current). The …

Responsivity measurements of SiC Schottky photodiodes

We investigated the technical features of three novel classes of 4H-SiC vertical Schottky UV detectors employing Ni2Si interdigitated strips whose pitch size is 8, 10 and 20 µm, respectively, based on the pinch-off surface effect.

Signal to Noise Ratio of Silicon Photomultipliers measured in the Continuous Wave Regime

We performed a Signal to Noise Ratio characterization, in the continuous wave regime, at different bias voltages, frequencies and temperatures, on a novel class of silicon photomultipliers fabricated in planar technology on silicon p-type substrate. Signal to Noise Ratio has been measured as the ratio of the photogenerated current, filtered and averaged by a lock-in amplifier, and the Root Mean Square deviation of the overall current flowing to the device. The measured noise takes into account the shot noise, resulting from the photocurrent and the dark current. We have also performed a comparison between our SiPMs and a photomultiplier tube in terms of Signal to Noise Ratio, as a function …

Responsivity measurements of silicon carbide Schottky photodiodes in the UV range

We report on the design and the electro-optical characterization of new classes of 4H-SiC Schottky UV detectors, fabricated employing Ni 2 Si interdigitated strips. We have measured, in dark conditions, the forward and reverse I-V characteristics as a function of temperature and C-V characteristics. Responsivity measurements of the devices, as function of wavelength in the UV range, of package temperature and of applied reverse bias are reported. We also compared devices featuring different strip pitch sizes, discussing their performances, and found the device exhibiting best results.

Design and development of a continuous wave functional near infrared spectroscopy system

Functional Near InfraRed Spectroscopy uses light sources and optical detectors for human brain monitoring. In this paper, a portable, low cost, battery-operated, multi-channel, continuous wave fNIRS embedded system, hosting up to 64 LED sources and 128 Silicon PhotoMultiplier optical detectors, is reported on. The designed system is based on a scalable architecture, in which each probe consists of 8 modular and flexible stands, able to host 4 bi-color LEDs as light sources, 16 silicon photomultipliers as photodetectors and a temperature sensor. The hardware structure allows to easily set up several relevant parameters: the timing of the LEDs, the optical power emitted by the LEDs; the acqui…

CIGS PV Module Characteristic Curves Under Chemical Composition and Thickness Variations

This paper analyzes how the electrical characteristics of a CIGS photovoltaic module are affected by the chemical composition and by the thickness variations of the CIGS absorber. The electrical characteristics here considered are the short circuit current, the open circuit voltage, the efficiency and the power peak. The chemical composition is varied by tuning the ratio between gallium and indium. This analysis has been performed by means of the wxAMPS software, developed by the University of Illinois. The above variations have been taken into account on a PV module made of 72 cells. This analysis has been carried out employing a PV module mathematical model developed and implemented by th…

Design and realization of a portable multichannel continuous wave fNIRS

A design and implementation of a portable functional Near InfraRed Spectroscopy embedded system prototype is described. In this theoretical and experimental work, we present an embedded system hosting 64 LED sources and 128 Silicon PhotoMultiplier detectors (SiPM). The elementary part of the structure is a flexible probe “leaf” consisting of 16 SiPMs, 4 couples of LEDs, each operating at two wavelengths, and a temperature sensor. The hardware system is based on an ARM main microcontroller that allows to perform both the switching time of LEDs and the acquisition of the SiPM outputs. The performed preliminary experimental tests achieved very promising results, thus demonstrating the effectiv…

Design and development of a fNIRS system prototype based on SiPM detectors

Functional Near Infrared Spectroscopy (fNIRS) uses near infrared sources and detectors to measure changes in absorption due to neurovascular dynamics in response to brain activation. The use of Silicon Photomultipliers (SiPMs) in a fNIRS system has been estimated potentially able to increase the spatial resolution. Dedicated SiPM sensors have been designed and fabricated by using an optimized process. Electrical and optical characterizations are presented. The design and implementation of a portable fNIRS embedded system, hosting up to 64 IR-LED sources and 128 SiPM sensors, has been carried out. The system has been based on a scalable architecture whose elementary leaf is a flexible board …

An innovative mechanical converter for sea wave application

This paper describes an innovative mechanical converter, usable in sea wave energy sector. This system transforms a variable bidirectional linear motion into a unidirectional rotary motion.

Design and implementation of a portable fNIRS embedded system

We report on the design, development and operation of a portable, low cost, battery-operated, multi-channel, functional Near Infrared Spectroscopy embedded system, hosting up to 64 optical sources and 128 Silicon PhotoMultiplier optical detectors. The system is realized as a scalable architecture, whose elementary leaf consists of a probe board provided with 16 SiPMs, 4 couples of bi-color LED, and a temperature sensor, built on a flexible stand. The hardware structure is very versatile because it is possible to handle both the switching time of the LED and the acquisition of the photodetectors, via an ARM based microcontroller.

Progettazione e realizzazione di un sistema Continuous Wave fNIRS basato su tecnologia SiPM

Design of a Multichannel Continuous Wave fNIRS System implemented with SiPM

Responsivity measurements of 4H-SiC Schottky photodiodes for UV light monitoring

We report on the design and the electro-optical characterization of a novel class of 4H-SiC vertical Schottky UV detectors, based on the pinch-off surface effect and obtained employing Ni2Si interdigitated strips. We have measured, in dark conditions, the forward and reverse I–V characteristics as a function of the temperature and the C–V characteristics. Responsivity measurements of the devices, as a function of the wavelength (in the 200 – 400 nm range), of the package temperature and of the applied reverse bias are reported. We compared devices featured by different strip pitch size, and found that the 10 μm device pitch exhibits the best results, being the best compromise in terms of fu…

Opals infiltrated with a stimuli-responsive hydrogel for ethanol vapor sensing

We report on a novel class of optical materials for ethanol vapor sensing, based on polystyrene opals infiltrated with an innovative stimuli responsive hydrogel. We describe the fabrication process of the bare polystyrene opals and their subsequent infiltration. The optical characterization of the photonic crystal templates was performed to prove the good quality of the samples. Measurements on the infiltrated opals showed that the transmission spectra in the visible range strongly change at varying concentrations of ethanol vapor. The fabricated structures show a linear optical response in the visible range, for high values of ethanol concentration.

Characterization of Thin Film CIG(S,Se)2 submodules using Laser Beam Induced Current Technique

Nowadays, an important class of thin film solar cells consists of CuInGa(S,Se)2 (CIGSSe) solar cells, i.e., composed of Copper, Indium, Gallium, Sulfur and Selenide. Thanks to their electrical and optical properties and to the technological development, thin film integrated photovoltaic modules have nowadays obtained relatively good values of efficiency. In this work, we have performed the electrical and optical characterization of a CIGSSe sub-module by using both a solar simulator equipment and the Laser Beam Induced Current (LBIC) technique.

Correlated Channel Model for terrestrial Free Space Optics and project specifications evaluation of LT code in OOK modulation

Free Space Optics is a wireless line-of-sight communication system able to offer good bandwidth performance as well as straightforward installation and relocation. So that it represents a modern technology that allow to realize large bandwidth communication particularly when it is not possible to employ physical cable or radio technologies. Examples of FSO applications are: wireless backaul, fiber backup, temporary links, metro network extension and last mile access[1]. FSO is based on optical signals propagation in air and that is why it suffers of impairments which depend on atmospheric conditions. In detail, FSO suffers of scattering (i. e. Rayleigh and Mie) losses, absorption and scinti…

Brain Monitoring Via an Innovative CW-FNIRS System

Functional Near InfraRed Spectroscopy (fNIRS) is an imaging technique mainly devoted to human brain monitoring. It is used as a non-invasive technique, in medical field, in order to measure the oxygen concentration of blood. This because the relatively good transparency of biological materials in the near infrared allows sufficient photon transmission through tissues. Within the so-called fNIRS range (650-900 nm), the main absorbers are blood chromophores, in particular the oxygenated and deoxygenated haemoglobin (HbO2 and Hb, respectively). When two or more wavelengths are used, changes of such chromophores can be computed by employing the modified Beer-Lambert law, thus providing importan…

Electrical characterization of highefficiency bifacial silicon solar cells

This work presents a preliminary study on the electrical characterization of high efficiency bifacial solar cells. An opening discussion on the state-of-the-art of such advanced technology is initially proposed and the experimental characterization of some prototypes is described. From this analysis, it can be stated that the bifacial silicon solar cells can be a very promising technology with high electrical performances and efficiency.

Parametrical study of multilayer structures for CIGS solar cells

In this paper, a numerical analysis of relevant electrical parameters of multilayer structures for CIGS-based solar cells was carried out, employing the simulation software wxAMPS. In particular, we have focused on thin film cells having a ZnO:Al/ZnO/CdS/CIGS structure with a Molybdenum back contact. The aim of this work is to establish good theoretical reference values for an ongoing experimental activity, where our technology of choice is the single-step electrodeposition. In detail, we have analyzed how the main electrical properties change with the bang gap and the thickness of the absorber layer, for such a type of solar cell structure. Our results show that both efficiency and fill fa…

Responsivity measurements of N-on-P and P-on-N silicon photomultipliers in the continuous wave regime

We report the electrical and optical comparison, in continuous wave regime, of two novel classes of silicon photomultipliers (SiPMs) fabricated in planar technology on silicon P-type and N-type substrate respectively. Responsivity measurements have been performed with an incident optical power from tenths of picowatts to hundreds of nanowatts and on a broad spectrum, ranging from ultraviolet to near infrared (340-820 nm). For both classes of investigated SiPMs, responsivity shows flat response versus the optical incident power, when a preset overvoltage and wavelength is applied . More in detail, this linear behavior extends up to about 10 nW for lower overvoltages, while a shrink is observ…

Anomalous electrical parameters improvement in Ruthenium DSSC

. In this work, we present a series of measurements carried out on Ruthenium-based Dye Sensitized Solar Cells (DSSCs) after the application of different external electrical field values. Such measurements have been performed both in the dark and by illuminating the sample with sunlight emitted by a solar simulator (AM1.5G spectrum with a power irradiance of 1000 W/m2). Our results demonstrate that the initial electrical bias field modifies in both cases the behavior of the cell in terms of an anomalous improvement of the main electrical parameters.

Experimental characterization of Ruthenium-based Dye Sensitized Solar Cells and study of light-soaking effect impact on performance

In this paper, we present an experimental investigation on the performance of Ruthenium-based Dye Sensitized Solar Cells (DSSCs) at different irradiance levels, incident wavelengths and hours of illumination. In particular, the measurements have been aimed at studying the performance variation due to light soaking effect since this phenomenon has noteworthy practical implications, such as stability tests of DSSCs. Our results show that the short circuit current density, the open circuit voltage and the conversion efficiency η increase with the hours of light soaking. Finally, the observed phenomenon is reversible, and thus the performance decreases again when the cell is kept in the dark.

Hydrogel films engineered in a mesoscopically ordered structure and responsive to ethanol vapors

Abstract Responsive hydrogels filling the interstitial spaces of photonic crystals can form mesoscopically structured materials, which exhibit reversible shifts in the Bragg diffracted light as a response of environmental changes. These materials can be used to generate chemical or biochemical sensors. The present work reports on the synthesis and characterization of ethanol responsive hydrogels that can be used in the design of novel breathalyzers. The dynamic mechanical behavior of the macroscopic hydrogels and their swelling features in the presence of different liquids or vapors have been investigated to orientate the choice of the best responsive material and curing process. The swelli…

Electro-Optical characterization of Silicon Carbide Schottky photodiodes

Characterization of thin film CIG(S,SE)2 submodules using solar simulator and laser beam induced current techniques (Versione estesa)

In this work, the electrical and optical characterization of CIG(S, Se)2 sub-modules using both a solar simulator equipment and the Laser Beam Induced Current (LBIC) technique is presented. By using the solar simulator and a proper set-up, the electrical parameters of the modules at varying irradiance and temperatures are determined. In addition, the LBIC measurements are carried out to analyze the 2D photocurrent uniformity of the modules at two different wavelengths. Dispersion values of extracted parameters can be very useful for practically tuning the modelling stage at device/module level.

Città di villeggiatura a Santa Cesarea Terme (LE)-2009

Progetto di masterplan per una piccola città di villegiatura a Santa Cesarea Terme (Le)CONCEPT DEL PIANO 1 Città di villeggiatura e commistione funzionale (Il programma funzionale) 2 Elementi di fondazione: “infrastrutture leggere” (Il viale e il tratturo) 3 Ricostruzione del paesaggio: strategia delle tipologie di vegetazione (Il paesaggio) 4 Integrazione nella rete delle strade esistenti (Le infrastrutture) 5 Intreccio tra spazi urbani e spazi della campagna (Gli spazi ed edifici pubblici/comuni) 6 Tracciati esistenti e nuovi tracciati regolatori (I muri, i recinti, le colture e le regole di impianto) / Uso variabile della densità (Le densità alta, media, bassa) 7 Gradualità dei microclim…

Measurements of Silicon Photomultipliers Responsivity

We present some results on the optical characterization of Silicon Photomultipliers designed for medical imaging applications. In particular we will discuss our responsivity measurements performed with very low incident optical power and on a broad spectrum

Optical sensors for ethanol vapor based on polystyrene opals infiltrated with hydrogel

This paper deals with a novel class of optical sensors for ethanol vapor, based on polystyrene opals infiltrated with a hydrogel sensitive to ethanol. Optical characterization of such opals has been performed, proving their effectiveness as sensors

A portable electronic system for non-invasive real-time acquisition of multiple physiological signals

In this work, we have designed and realised a portable and compact electronic system for the synchronous acquisition of multiple physiological signals. The system employs a Texas Instruments ADS1298 front-end with 24-bit resolution for data acquisition and supports up to 8 channels and 4 kHz sampling rate. The front-end communicates via SPI with a STM32 microcontroller which pre-processes the data and sends them through USB or Bluetooth to a suitable PC application. The system has been realized for the simultaneous acquisition of electrocardiographic (ECG) and photoplethysmographic (PPG) signals, but it can also be employed for acquiring other typologies of signals, e.g. breathing or electr…

Silicon Photomultipliers Signal-to-Noise Ratio in the Continuous Wave Regime

 Abstract— We report on Signal-to-Noise Ratio measurements carried out, in the continuous wave regime, at different bias voltages, frequencies and temperatures, on a class of silicon photomultipliers fabricated in planar technology on silicon p- type substrate. Signal-to-Noise Ratio has been measured as the ratio of the photogenerated current, filtered and averaged by a lock-in amplifier, and the Root Mean Square deviation of the same current. The measured noise takes into account the shot noise, resulting from the photocurrent and the dark current. We have also performed a comparison between our SiPMs and a photomultiplier tube in terms of Signal-to-Noise Ratio, as a function of the tempe…

Measurements of Silicon Photomultipliers Responsivity in Continuous Wave Regime

We report on the electrical and optical characterization, in continuous wave regime, of a novel class of silicon photomultipliers fabricated in standard planar technology on a silicon p-type substrate. Responsivity measurements, performed with an incident optical power down to tenths of picowatts, at different reverse bias voltages and on a broad (340–820 nm) spectrum, will be shown and discussed. The device temperature was monitored, allowing us to give a physical interpretation of the measurements. The obtained results demonstrate that such novel silicon photomultipliers are suitable as sensitive power meters for low photon fluxes.

Electro-optical characterization of new classes of Silicon Carbide UV photodetectors

In this paper, we present the fabrication process steps and the characterization of 4H-SiC vertical Schottky UV detectors, where interdigitated strips, acting as top metal contacts, have been realized in $\hbox{Ni}_{2}\hbox{Si}$ . These devices exploit the pinch-off surface effect. $I$ – $V$ and $C$ – $V$ characteristics, as functions of temperature, were measured in dark conditions. In addition, we have carried out responsivity measurements, for wavelengths ranging from 200 to 400 nm, at varying package temperature and applied reverse bias. A comparison among devices having different strip pitch sizes has been performed, thus finding out that the 10- $\mu\hbox{m}$ pitch class demonstrates …

Periodically nanostructured hydrogels for ethanol vapors sensing

Chemical sensing using optics has been under extensive research all over the world during last decades and many optical chemical sensors are nowadays finding increasing applications in industry, environmental monitoring, medicine, biomedicine and chemical analysis. These optical sensors can be based on various optical principles, such as absorbance, reflectance or transmittance, luminescence and fluorescence, covering different regions of the spectrum (UV, visible, IR, NIR). Optical chemical sensors have several advantages over conventional electricity-based sensors, in terms of selectivity, immunity to electromagnetic interference, higher sensitivity, and they are also relatively inexpensi…

Electro-optical characterization of highly efficient Dye-Sensitized solar cells

Nowadays, a growing demand for free and clean energy requires the study and the development of new low-cost solar photovoltaic (PV) cells. Among them, Dye Sensitized Solar Cells (DSSCs) based on ruthenium complexes as sensitizers are assuming a great importance. The DSSCs under study are composed placing in succession a transparent conductive glass on which is screen-printed a mesoporous TiO2 thin film sensitized by a ruthenium based dye (N719), an electrolytic solution containing a redox couple (I-/I3-) and another conductive glass covered by a thin transparent catalyst platinum film. In this work, we have measured the main photoelectrochemical parameters of the above mentioned DSSCs at di…

Optical characterization of polystyrene direct opals and of inverse-opal hydrogels

Cardiovascular parameters detection using a Photoplethismographic system

We propose an innovative, cost-effective and easy to employ photoplethysmographic (PPG) system using Silicon Photomultipliers (SiPMs) sensors to measure cardiovascular parameters that can potentially represent markers for arterial stiffness

Anomalous performance enhancement effects in Ruthenium-based Dye Sensitized Solar Cells

Dye Sensitized Solar Cells (DSSCs) are nowadays more and more employed since they present lower production costs than traditional silicon photovoltaic devices. An interesting phenomenon affecting such devices consists in the fact that current density-voltage (J-V) characteristic can depend on the history of the cell prior to the measurement, which often can be assimilated to an anomalous hysteresis effect. In this work, we study such phenomenon on Ruthenium-based DSSCs through a series of measurements performed after applying different values of external electrical field to the cell. The measurements have been carried out both under simulated sunlight (AM1.5G - 1000 W/m2) and in the dark. W…

Measurements of Silicon Photomultipliers Responsivity in Continuous Wave

A wideband THz Time Domain Spectroscopy system based on pulsed laser: model and experiments

Characterization of Thin Film Cig(S,Se)2 Submodules Using Solar Simulator and Laser Beam Induced Current Techniques

In this work, the electrical and optical characterization of CIG(S,Se)2 sub-modules using both a solar simulator equipment and the Laser Beam Induced Current (LBIC) technique is presented. By using the solar simulator and a proper set-up, the electrical parameters of the modules at varying irradiance and temperatures are determined. In addition, the LBIC measurements are carried out to analyze the 2D photocurrent uniformity of the modules at two different wavelengths. Dispersion values of extracted parameters can be very useful for practically tuning the modelling stage at device/module level.

Second Harmonic Generation via Random Quasi-phase Matching in a Periodically Poled Lithium Tantalate Waveguide

We observe second harmonic generation via random quasi phase matching in a 1.5μm periodically poled lithium tantalate. The presence of a slab waveguide allows the comparison between bulk and guided wave configurations.

TOF LiDAR with SiPM technology

LiDAR (Light Detection And Ranging) systems measures the distance from the sensor to the target by determining the time between the release of the laser pulse to the receiving of the backscattered pulse. The interest in LiDAR technology has exploded in recent years since the applications are numerous. Here, we would highlight the Advanced Driver Assistance Systems (ADAS) and for rendezvous & docking operations between spacecraft. We built two LiDAR systems differing for the detector: a Silicon Photomultiplier (SiPM) and an Avalanche Photodiode (APD). The advantages of the SiPM approach has been extensively discussed in [1]. The comparison between these systems has been performed in terms of…

Continuous Wave fNIRS with Silicon Photomultiplier

This work is focused on the development of a Continuous Wave (CW) NIRS integrated system with multi-wavelength LED sources between 700 and 950 nm and a Silicon Photomultiplier detector (SiPM) developed by STMicroelectronics. The Signal Noise Rate (SNR), measured placing the LEDs and an SiPM in a direct contact with the surface of a plastic phantom mimicking a real human head, results higher than the calculated minimum, required to detect small variation in the HbO2 and HHb concentration, till a source detector separation (SDS) of 6 cm.

Signal to Noise Ratio of Silicon Photomultipliers: a study in the Continuous Wave Regime

We report on Signal to Noise Ratio measurements carried out, in the continuous wave regime, at different bias voltages, frequencies and temperatures, on a novel class of silicon photomultipliers fabricated in planar technology on silicon p-type substrate. Signal to Noise Ratio has been measured as the ratio of the photogenerated current, filtered and averaged by a lock-in amplifier, and the Root Mean Square deviation of the same current. The measured noise takes into account the shot noise, resulting from the photocurrent and the dark current. We have also performed a comparison between our SiPMs and a photomultiplier tube in terms of Signal to Noise Ratio, as a function of the temperature …

SNR measurements of silicon photomultipliers in the continuous wave regime

We report on our Signal-to-Noise Ratio (SNR) measurements carried out, in the continuous wave regime, at different frequencies and at various temperatures, on a novel class of silicon photomultipliers (SiPMs) fabricated in planar technology on silicon p-type substrate. SNR of SiPMs is given by the ratio of the photogenerated current, filtered and averaged by a lock-in amplifier, and the Root Mean Square (RMS) deviation of the same current. In our measurements, we have employed a 10 Hz equivalent noise bandwidth, around the lock-in amplifier reference frequency. The measured noise takes into account the shot noise, resulting from the photocurrent and the dark current, while background light …

CuInSe2/Zn(S,O,OH) junction by electrochemical and chemical route for photovoltaic applications (GE 2014)

Electrodeposition is a convenient technique for the development of low cost materials for photovoltaic (PV) device processing. Using a single step electrodeposition route, several groups have fabricated CIS (CuInSe) and CIGS (CuInGaSe) films. One of the most important requirements for successful application of one-step electrodeposition film formation is the ability to control composition of the deposited films and to develop polycrystalline microstructures with a low surface roughness and high sintered density.

Optical turbulence measurements and channel modeling of an indoor Free Space Optics link

Photonic crystal hydrogel films responsive to ethanol vapors

Development of a CW-fNIRS System for brain monitoring

A portable system for multiple parameters monitoring: towards assessment of health conditions and stress level in the automotive field

In this work, an electronic portable combo system able to synchronously acquire multiple signals, e.g. electrocardiographic (ECG), photoplethysmographic (PPG) and breathing waveforms, is presented. The realized system is also capable of showing in real time some physiological parameters which can be used for assessing health/stress status of the volunteer, such as heart rate and breathing frequency and their trends over time. Thanks to the use of non-invasive PPG probes, of batteries as power supply, and to the possibility to add in the future additional sensors to acquire other signals, the system could also be employed inside vehicles for assessing the status of the driver. Finally, the r…

Physiological parameters measurements in a cardiac cycle via a combo PPG-ECG system

In this paper, we present an innovative way to measure some physiological parameters (such as the pre-ejection period, the pulse transit time, the blood pressure) in a cardiac cycle. A combo PPG-ECG system has been developed and employed to extract both the ECG signal from standard limb leads and simultaneously the photoplethysmography signal from the wrist and the forearm, to calculate the pre-ejection period. This system represents an easy and non-invasive technique to determine these biomedical parameters without using expensive impedance cardiography equipment.

Blood Pressure Monitoring with a PPG Embedded System

P-on-N and N-on-P silicon photomultipliers: an in-depth analysis in the continuous wave regime

We report on the electrical and optical comparison, in the continuous wave regime, of two novel classes of silicon photomultipliers fabricated in planar technology on silicon P-type (N-on-P class) and N-type (P-on-N class) substrates respectively.

Laser Beam Induced Current measurements on Dye Sensitized Solar Cells and thin film CIG(S,SE)<inf>2</inf> modules

Calculating the efficiency of a solar cell depends on a precise knowledge of its area. Indeed, the photoresponse uniformity is essential to improve the manufacturing process. In this work we report on Laser Beam Induced Current measurements performed on CIG(S,Se) 2 modules and Dye Sensitized Solar Cells. These measurements, performed via a green and a red HeNe lasers both operating at an optical irradiance of 1 Sun, allowed to obtain an accurate photoresponse map of the specimens and highlighted the non-uniformities with a spatial resolution of 400 µm and 80 µm, respectively.

Optical turbulence measurements and channel modeling of an indoor Free Space Optics link (Versione estesa)

In this work, we propose an indoor experimental set-up able to generate several optical turbulence conditions in a Free Space Optics link. Using this set-up, we prove the effectiveness of an irradiance time-series generator based on the Gamma-Gamma model and able to predict the irradiance fluctuations at the receiver, under both weak and moderate turbulence conditions.

A LiDAR Prototype with Silicon Photomultiplier and MEMS Mirrors

In this paper, we present a low cost prototype of a Time-Of-Flight (TOF) LiDAR system, employing a SiPM as photo detector and MEMS mirrors in order to steer the nanosecond pulsed optical beam with a scanning angle of +/-6°. Preliminary TOF measurements have been performed both indoor and outdoor to test the limits of the system.

Comparison in terms of TOF measurements between APD and SiPM for LiDAR applications

We present an experimental comparison of two LiDAR systems, employing the SiPM and the APD as photodetectors, in terms of TOF measurements differing for the distance of the target and at different intensities of ambient light. The use of the APD represents the conventional approach, while the implementation of the SiPM is innovative. The performed measurements achieved very promising results, thus demonstrating the effectiveness of our LiDAR based on SiPM.