Performance of a membrane-coupled high-rate algal pond for urban wastewater treatment at demonstration scale

[EN] The objective of this study was to evaluate the performance of an outdoor membrane-coupled high-rate algal pond equipped with industrial-scale membranes for treating urban wastewater. Decoupling biomass retention time (BRT) and hydraulic retention time (HRT) by membrane filtration resulted in improved process efficiencies, with higher biomass productivities and nutrient removal rates when operating at low HRTs. At 6 days of BRT, biomass productivity increased from 30 to 66 and to 95 g.m(-3).d(-1) when operating at HRTs of 6, 4 and 2.5 days, respectively. The corresponding nitrogen removal rates were 4, 8 and 11 g N.m(-3).d(-1) and the phosphorous removal rates were 0.5, 1.3 and 1.6 g P…

Harvesting Energy from Wastewater Using an Innovative Anaerobic Membrane Bioreactor

Relating ions concentration variations to conductivity variations in a sequencing batch reactor operated for enhanced biological phosphorus removal

In this paper a deterministic relationship between ionic conductivity and phosphorus concentration variations in an enhanced biological phosphorus removal (EBPR) process is established. Conductivity shows a strong correlation with phosphorus in both anaerobic and aerobic stages, increasing or decreasing when phosphorus is released or taken up, respectively. Since the end of these processes can be detected by examining the conductivity profile in a cycle, useful information on the EBPR performance and stability is available. This information can be used for adjusting the length of the anaerobic and aerobic stages. Therefore, online process control based on inexpensive and easy to maintain se…

Cadmium and Copper Removal by a Granular Activated Carbon in Laboratory Column Systems

Single and competitive removal of Cd and Cu from aqueous solutions by using Darco 12–20 mesh granular activated carbon in column systems has been investigated. Seven experiments modifying the initial pH and the flow rate were performed. Results showed the efficiency of activated carbon as a sorbent for both metals. pH is shown to be the decisive parameter on metal removal in the column; metal removal increases when the influent pH value is raised. The influence of the flow rate for the experimental conditions is negligible. Batch adsorption and column data are compared. Column modeling assuming local equilibrium and rate-controlled pore diffusion was performed.

Use of biological and sedimentation models for designing Peñíscola WWTP.

This paper presents Peñíscola wastewater treatment plant design. Peñíscola is a tourist city in Castellón (Spain), whose population changes significantly between summer and the rest of the year. The design of the biological and settling treatment units has been confirmed by computer model simulations and provided for biological organic matter, nitrogen and phosphorus removal. Two different treatment schemes have been proposed in order to optimize the plant performance during both seasonal operations. During low-load season, the plant will be operated under extended aeration conditions, so further sludge stabilization will not be needed. During high-load season, the plant will be operated un…

Low cost-sensors as a real alternative to on-line nitrogen analysers in continuous systems.

This paper is focused on the evaluation of the applicability of low-cost sensors (pH and ORP) versus nutrient analysers for controlling biological nitrogen removal in WWTPs. A nutrient removal pilot plant located in Carraixet WWTP (Valencia, Spain) that is equipped with a significant number of nutrient analysers and low-cost sensors was used. The relations between reliable, cheap on-line sensors such as pH and ORP (located in anaerobic, anoxic and aerobic zones) and the nitrification/denitrification processes are provided. The nitrification process can be evaluated by measuring the pH difference between the first and last aerobic zones. The denitrification process can be evaluated by measur…

Natural organic matter coagulation in Valencia water supply. Pilot plant studies

: To reduce disinfection by-product (DBP) formation in drinking water treatment, the presence of natural organic matter in surface waters must be minimised. This paper describes pilot plant studies carried out on two surface waters to assess the effectiveness of coagulation in organic matter removal, the Turia and Jucar rivers, which supply the city of Valencia (1m inhabitants). The experiments were conducted with different coagulants (iron sulphate, polyaluminium chloride (PACl)) and treatment schemes. Process effectiveness was evaluated in terms of effluent turbidity, presence of residual metal in final water, and organic matter removal. Four parameters were used to quantify organic matte…

Metabolic shift of polyphosphate-accumulating organisms with different levels of polyphosphate storage

Previous studies have shown that polyphosphate-accumulating organisms (PAOs) are able to behave as glycogen-accumulating organisms (GAOs) under different conditions. In this study we investigated the behavior of a culture enriched with Accumulibacter at different levels of polyphosphate (poly-P) storage. The results of stoichiometric ratios Gly degraded/HAc uptake, PHB synthesized/HAc uptake, PHV synthesized/HAc uptake and P release/HAc uptake confirmed a metabolic shift from PAO metabolism to GAO metabolism: PAOs with high poly-P content used the poly-P to obtain adenosine tri-phosphate (ATP), and glycogen (Gly) to obtain nicotinamide adenine dinucleotide (NADH) and some ATP. In a test whe…

Removal of algae from biological cultures: a challenge for electrocoagulation?

BACKGROUND In the search for novel technologies for the treatment of urban wastewater, combined anaerobic–algae membrane bioreactors have become a very interesting choice. Recovery of algae produced in these reactors has become the key point to obtain a good economic efficiency with this technology. In this work, electrocoagulation is studied as an alternative for the coarse removal of algae from a biological culture. RESULTS Results demonstrate that the electrochemical technology is a suitable technology for this purpose allowing the removal of more than 90% of the algae without modifying significantly the pH and with an operating cost below 0.04 € m−3. The same general trends are observed…

Using Unfold-PCA for batch-to-batch start-up process understanding and steady-state identification in a sequencing batch reactor

In chemical and biochemical processes, steady-state models are widely used for process assessment, control and optimisation. In these models, parameter adjustment requires data collected under nearly steady-state conditions. Several approaches have been developed for steady-state identification (SSID) in continuous processes, but no attempt has been made to adapt them to the singularities of batch processes. The main aim of this paper is to propose an automated method based on batch-wise unfolding of the three-way batch process data followed by a principal component analysis (Unfold-PCA) in combination with the methodology of Brown and Rhinehart 2 for SSID. A second goal of this paper is to…

A mathematical approach to predict the solids concentration in anaerobic membrane bioreactos (AnMBR): Evaluation of the volatile solids solubilization

[EN] Anaerobic Membrane Bioreactors (AnMBR) are gaining attention as a suitable approach for sustainable low-strength wastewater treatment, as they bring together the advantages of both anaerobic treatments and membrane bioreactors. However, increasing the sludge retention time (SRT) necessary to favor hydrolysis increases the suspended solids concentration potentially leading to decreased permeate flux. Therefore, the availability of a mathematical approach to predict the solids concentration within an AnMBR can be very useful. In this work, a mathematical model describing the volatile solids concentration within the reactor as a function of the operating parameters and the influent charac…

Process understanding of a wastewater batch reactor with block-wise PLS

In this work a systematic methodology ‘block-wise PLS’ has been applied to thoroughly analyse data from a sequencing batch reactor (SBR) operated for biological phosphorus removal from wastewater. The aim of this study was to diagnose process variables (collected by the inexpensive and low-maintenance sensors installed in the SBR) likely related to the main key indicator of process performance: the phosphorus removal efficiency (PRE), determined off-line in the quality control laboratory. In this way, it is intended to aid the process operators in the detection of abnormal values of these critical variables which would indicate undesirable process performance, so that, they could act on the…

Characterization of activated sludge settling properties with a sludge collapse-acceleration stage

Abstract The sedimentability of the activated sludge can be affected by the presence of a large variety of coagulants and polymers from a previous physical-chemical process. In this paper, the activated sludge settling process in industrial wastewater treatment plants where the sludge does not settle in a conventional way is studied. The two observed constant hindered settling velocity stages and the instant the intermediate sludge acceleration period occurs are described. A variation of the Richardson and Zaki model is used to characterize the two stages of constant settling velocity. The concentration of suspended solids, where a sudden decrease of hindered settling velocity was observed,…

Behavior of mixed Chlorophyceae cultures under prolonged dark exposure. Respiration rate modeling

[EN] The behavior of three different microalgal cultures, when exposed for a long period (>48 h) to dark conditions, was studied with a methodology based on respirometry. The cultures were transferred to darkness and the oxygen evolution in the reactors was monitored after successive air injections. Several sequential oxygen uptake rates were thus calculated and a respiration constant, assuming a first order decay of a fraction of the biomass, was obtained by calibration. Initial specific oxygen uptake rates were in the range of 0.9 5.1 mg O2 g TSS−1 h−1 and dark respiration constants in the range of 0.005 0.018 h−1.

Production of microalgal external organic matter in a Chlorella-dominated culture: influence of temperature and stress factors

[EN] Although microalgae are recognised to release external organic matter (EOM), little is known about this phenomenon in microalgae cultivation systems, especially on a large scale. A study on the effect of microalgae-stressing factors such as temperature, nutrient limitation and ammonium oxidising bacteria (AOB) competition in EOM production by microalgae was carried out. The results showed non-statistically significant differences in EOM production at constant temperatures of 25, 30 and 35 degrees C. However, when the temperature was raised from 25 to 35 degrees C for 4 h a day, polysaccharide production increased significantly, indicating microalgae stress. Nutrient limitation also see…

Cadmium and Zinc Adsorption onto Activated Carbon: Influence of Temperature, pH and Metal/Carbon Ratio

The adsorption characteristics of cadmium and zinc onto a granular activated carbon were studied. Cadmium and zinc removals increased on raising pH and temperature, and decreased on raising the molar metal/carbon ratio. The adsorption processes were modelled using the surface complex formation (SCF) Triple Layer Model (TLM) with an overall bidentate species. A dependence of the SCF constant on pH, the molar metal/carbon ratio and temperature was observed, and a correlation for log K ads was determined. The SCF model successfully predicted cadmium and zinc removals.

Assessment of cross-flow filtration as microalgae harvesting technique prior to anaerobic digestion: Evaluation of biomass integrity and energy demand

[EN] In the present study, the effect of cross-flow filtration (CFF) on the overall valorization of Chlorella spp. microalgae as biogas was assessed. The effect of CFF on microalgae cell integrity was quantified in terms of viability which was correlated with the anaerobic biodegradability. The viability dropped as the biomass concentration increased, whereas anaerobic biodegradability increased linearly with the viability reduction. It was hypothesized that a stress-induced release and further accumulation of organic polymers during CFF increased the flux resistance which promoted harsher shear-stress conditions. Furthermore, the volume reduction as the concentration increased entailed an …

Co-digestion of harvested microalgae and primary sludge in a mesophilic anaerobic membrane bioreactor (AnMBR): Methane potential and microbial diversity

Abstract Anaerobic co-digestion of primary sludge and raw microalgae (Scenedesmus and Chlorella) was performed in a lab-scale semi-continuous anaerobic membrane bioreactor to assess the biological performance and identify the microbial community involved in the co-digestion process. The reactor was operated at 35 °C for 440 days, working at a solids retention time of 100 days. The system achieved 73% biodegradability and showed high stability in terms of pH and volatile fatty acids. An enriched microbial community was observed. Of the several phyla, Chloroflexi and Proteobacteria were the most abundant. Cellulose-degraders phyla (Bacteroidetes, Chloroflexi and Thermotogae) were detected. Sy…

Resource recovery from sulphate-rich sewage through an innovative anaerobic-based water resource recovery facility (WRRF)

[EN] This research work proposes an innovative water resource recovery facility (WRRF) for the recovery of energy, nutrients and reclaimed water from sewage, which represents a promising approach towards enhanced circular economy scenarios. To this aim, anaerobic technology, microalgae cultivation, and membrane technology were combined in a dedicated platform. The proposed platform produces a high-quality solid- and coliform-free effluent that can be directly discharged to receiving water bodies identified as sensitive areas. Specifically, the content of organic matter, nitrogen and phosphorus in the effluent was 45 mg COD.L-1 , 14.9 mg N.L-1 and 0.5 mg P.L-1 , respectively. Harvested solar…

An extension of ASM2d including pH calculation

This paper presents an extension of the Activated Sludge Model No. 2d (ASM2d) including a chemical model able to calculate the pH value in biological processes. The developed chemical model incorporates the complete set of chemical species affecting the pH value to ASM2d describing non-equilibrium biochemical processes. It considers the system formed by one aqueous phase, in which biochemical processes take place, and one gaseous phase, and is based on the assumptions of instantaneous chemical equilibrium under liquid phase and kinetically governed mass transport between the liquid and gas phase. The ASM2d enlargement comprises the addition of every component affecting the pH value and an i…

Application of a fuzzy algorithm for pH control in a struvite crystallisation reactor

A struvite crystallisation process is highly dependent on pH. To achieve a high phosphorus recovery as struvite it is important to have an accurate control of pH in the reactor. The high non-linear response of pH value makes manual pH control difficult. Therefore, a software based on fuzzy logic control (FLC) has been developed to maintain the pH at a set value in a stirred reactor to crystallise struvite. The FLC developed has been based on Larsen's inference. In order to confirm the improvement of the pH stability using FLC software, different experiments have been carried out with manual control of the pH value, and with the FLC software. It has been demonstrated that using FLC software …

Calibration of denitrifying activity of polyphosphate accumulating organisms in an extended ASM2d model

Abstract This paper presents the results of an experimental study for the modelling and calibration of denitrifying activity of polyphosphate accumulating organisms (PAOs) in full-scale WWTPs that incorporate simultaneous nitrogen and phosphorus removal. The convenience of using different yields under aerobic and anoxic conditions for modelling biological phosphorus removal processes with the ASM2d has been demonstrated. Thus, parameter ηPAO in the model is given a physical meaning and represents the fraction of PAOs that are able to follow the DPAO metabolism. Using stoichiometric relationships, which are based on assumed biochemical pathways, the anoxic yields considered in the extended A…

Model performance of partial least squares in utilizing the visible spectroscopy data for estimation of algal biomass in a photobioreactor

[EN] Spectroscopy technology and statistical methods (Partial Least Squares) have been integrated to develop a model that allows estimating the microalgal biomass in a photobioreactor. The model employing PLS combines the absorption spectrum measurements in the visible range (400-750 nm) with a microalgae cell density in a water sample. First, a calibration model was constructed using a calibration data set, and then, the predictive capacity of the model was determined by cross validation. Finally, an external validation of the predictive performance of the model was carried out with an independent data set. To test the accuracy of the model it was applied to different culture conditions yi…

New frontiers from removal to recycling of nitrogen and phosphorus from wastewater in the Circular Economy

[EN] Nutrient recovery technologies are rapidly expanding due to the need for the appropriate recycling of key elements from waste resources in order to move towards a truly sustainable modern society based on the Circular Economy. Nutrient recycling is a promising strategy for reducing the depletion of non-renewable resources and the environmental impact linked to their extraction and manufacture. However, nutrient recovery technologies are not yet fully mature, as further research is needed to optimize process efficiency and enhance their commercial applicability. This paper reviews state-of-the-art of nutrient recovery, focusing on frontier technological advances and economic and environ…

Evaluation of activated sludge model no.2 at high phosphorus concentrations

This paper presents laboratory scale experimentation carried out to study enhanced biological phosphorus removal at high phosphorus concentrations in a sequencing batch reactor. Four series of data obtained in a sequencing batch reactor are examined in light of the Activated Sludge Model No. 2. This model was calibrated using data from the first and second series working at low phosphorus concentrations. The Activated Sludge Model No. 2 successfully characterised the enhanced biological phosphorus removal performance of the sequencing batch reactor at low phosphorus concentrations. The calibrated model was then used to adjust experimental results of the other series working at high phosphor…

A new strategy to maximize organic matter valorization in municipalities: combination of urban wastewater with kitchen food waste and its treatment with AnMBR technology

[EN] The aim of this study was to evaluate the feasibility of treating the kitchen food waste (FW) jointly with urban wastewater (WW) in a wastewater treatment plant (WWTP) by anaerobic membrane technology (AnMBR). The experience was carried out in six different periods in an AnMBR pilot-plant for a total of 536 days, varying the SRT, HRT and the food waste penetration factor (PF) of food waste disposers. The results showed increased methane production of up to 190% at 70 days SRT, 24 hours HRT and 80% PF, compared with WW treatment only. FW COD and biodegradability were higher than in WW, so that the incorporation of FW into the treatment increases the organic load and the methane producti…

Calcium phosphate precipitation in a SBR operated for EBPR: interactions with the biological process.

The aim of this paper is to study the precipitation process in a sequencing batch reactor (SBR) operated for EBPR (enhanced biological phosphorus removal) and the possible effects of this phosphorus precipitation in the biological process. Four experiments were carried out under different influent calcium concentration. The experimental results and the equilibrium study, based on the Saturation Index calculation, confirm that the process controlling the calcium behaviour in a SBR operated for EBPR is the calcium phosphate precipitation. This precipitation takes place at two stages initially precipitation of the ACP and later crystallization of HAP. Also the accumulation of phosphorus precip…

Economic analysis of the scale-up and implantation of a hollow fibre membrane contactor plant for nitrogen recovery in a full-scale wastewater treatment plant

[EN] Nitrogen recovery technologies such as the hollow fibre membrane contactor are now being developed. However, an economic analysis is needed prior to their full-scale application in wastewater treatment plants. The aim of this study was to analyse the economic and environmental aspects of scaling-up this method. To achieve it, a full-scale 40,000 m3·day¿1-wastewater treatment plant influent flow rate was simulated jointly with a membrane contactor plant to evaluate the minimum costs of optimum operating conditions of membrane contactors (pH, feed flow rate and membrane surface). The optimum conditions for treating 600 m3·day¿1 of reject water was found to be 10 pH, 0.08 m3·s¿1 feed flow…

Removal and fate of endocrine disruptors chemicals under lab-scalepostreatment stage. Removal assessment using light, oxygen and microalgae

[EN] The aim of this study was to assess the effect of light, oxygen and microalgae on micropollutants removal. The studied micropollutants were 4-(1,1,3,3-tetramethylbutyl)phenol (OP), technical-nonylphenol (t-NP), 4-n-nonylphenol (4-NP), Bisphenol-A (BPA). In order to study the effect of the three variables on the micropollutants removal, a factorial design was developed. The experiments were carried out in four batch reactors which treated the effluent of an anaerobic membrane bioreactor. The gas chromatography mass spectrometry was used for the measurement of the micropollutants. The results showed that light, oxygen and microalgae affected differently to the degradation ratios of each …

Experimental study of the anaerobic urban wastewater treatment in a submerged hollow-fibre membrane bioreactor at pilot scale

The aim of this study was to assess the effect of several operational variables on both biological and separation process performance in a submerged anaerobic membrane bioreactor pilot plant that treats urban wastewater. The pilot plant is equipped with two industrial hollow-fibre ultrafiltration membrane modules (PURON¿ Koch Membrane Systems, 30m 2 of filtration surface each). It was operated under mesophilic conditions (at 33°C), 70days of SRT, and variable HRT ranging from 20 to 6h. The effects of the influent COD/SO 4-S ratio (ranging from 2 to 12) and the MLTS concentration (ranging from 6 to 22gL -1) were also analysed. The main performance results were about 87% of COD removal, efflu…

Struvite formation from the supernatants of an anaerobic digestion pilot plant

This work studied the influence of the characteristics of the supernatants on the struvite precipitation process. Eighteen experiments with the supernatants generated in an anaerobic digestion pilot plant were performed in a stirred reactor. In order to obtain the pH control during the crystallization process, a Fuzzy Logic based controller was used. High phosphorus precipitation and recovery efficiencies were obtained. The composition of the supernatants was analyzed in order to study its influence on the solids formed from those solutions. The presence of calcium reduced the percentage of phosphorus precipitated as struvite leading to the formation of amorphous calcium phosphate (ACP), wh…

Monitoring pH and ORP in a SHARON reactor

This paper analyses the valuable information provided by the on-line measurements of pH and oxidation reduction potential (ORP) in a continuous single high ammonia removal over nitrite (SHARON) reactor. A laboratory-scale SHARON reactor equipped with pH, ORP, electric conductivity and dissolved oxygen (DO) probes has been operated for more than one year. Nitrogen removal over nitrite has been achieved by adding methanol at the beginning of anoxic stages. Time evolution of pH and ORP along each cycle allows identifying the decrease in nitritation rate when ammonia is consumed during the aerobic phase and the end of the denitrification process during the anoxic phase. Therefore, monitoring pH…

Outdoor flat-panel membrane photobioreactor to treat the effluent of an anaerobic membrane bioreactor. Influence of operating, design, and environmental conditions

[EN] As microalgae have the ability to simultaneously remove nutrients from wastewater streams while producing valuable biomass, microalgae-based wastewater treatment is a win-win strategy. Although recent advances have been made in this field in lab conditions, the transition to outdoor conditions on an industrial scale must be further investigated. In this work an outdoor pilot-scale membrane photobioreactor plant was operated for tertiary sewage treatment. The effects of different parameters on microalgae performance were studied including: temperature, light irradiance (solar and artificial irradiance), hydraulic retention time (HRT), biomass retention time (BRT), air sparging system an…

Plant-wide modelling in wastewater treatment: showcasing experiences using the Biological Nutrient Removal Model

Abstract Plant-wide modelling can be considered an appropriate approach to represent the current complexity in water resource recovery facilities, reproducing all known phenomena in the different process units. Nonetheless, novel processes and new treatment schemes are still being developed and need to be fully incorporated in these models. This work presents a short chronological overview of some of the most relevant plant-wide models for wastewater treatment, as well as the authors' experience in plant-wide modelling using the general model BNRM (Biological Nutrient Removal Model), illustrating the key role of general models (also known as supermodels) in the field of wastewater treatment…

Short-term effect of ammonia concentration and salinity on activity of ammonia oxidizing bacteria.

A continuously aerated SHARON (single reactor high activity ammonia removal over nitrite) system has been operated to achieve partial nitritation. Two sets of batch experiments were carried out to study the effect of ammonia concentration and salinity on the activity of ammonia-oxidizing bacteria (AOB). Activity of AOB raised as free ammonia concentration was increased reaching its maximum value at 4.5 mg NH 3 -N l −1 . The half saturation constant for free ammonia was determined (K NH 3 = 0.32 mg NH 3 -N l −1 ). Activity decreased at TAN (total ammonium–nitrogen) concentration over 2,000 mg NH 4 -N l −1 . No free ammonia inhibition was detected. The effect of salinity was studied by adding…

Modeling light and temperature influence on ammonium removal by Scenedesmus sp. under outdoor conditions.

[EN] The ammonium removal rate of the microalga Scenedesmus sp. was studied under outdoor conditions. Microalgae were grown in a 500 L flat-plate photobioreactor and fed with the effluent of a submerged anaerobic membrane bioreactor. Temperature ranged between 9.5 WC and 32.5 WC and maximum light intensity was 1,860 μmol·m2·s1. A maximum specific ammonium removal rate of 3.71 mg NH4 þ-N·g TSS1·h1 was measured (at 22.6 WC and with a light intensity of 1,734 μmol·m2·s1). A mathematical model considering the influence of ammonium concentration, light and temperature was validated. The model successfully reproduced the observed values of ammonium removal rate obtained and it is thus p…

DESASS: A software tool for designing, simulating and optimising WWTPs

This paper presents a very useful software tool to design, simulate and optimise wastewater treatment plants. The program is called DESASS (DEsign and Simulation of Activated Sludge Systems) and has been developed by CALAGUA research group. The mathematical model implemented is the Biological Nutrient Removal Model No.1 (BNRM1) which allows simulating the most important physical, chemical and biological processes taking place in treatment plants. DESASS calculates the performance under steady or transient state of whole treatment schemes including primary settlers, volatile fatty acid generation systems by primary sludge fermentation, activated sludge systems for biological organic matter a…

A semi-industrial scale AnMBR for municipal wastewater treatment at ambient temperature: performance of the biological process

A semi-industrial scale AnMBR plant was operated for more than 600 days to evaluate the long-term operation of this technology at ambient temperature (ranging from 10 to 27 ºC), variable hydraulic retention times (HRT) (from 25 to 41 h) and influent loads (mostly between 15 and 45 kg COD·d−1). The plant was fed with sulfate-rich high-loaded municipal wastewater from the pre-treatment of a full-scale WWTP. The results showed promising AnMBR performance as the core technology for wastewater treatment, obtaining an average 87.2 ± 6.1 % COD removal during long-term operation, with 40 % of the data over 90%. Five periods were considered to evaluate the effect of HRT, influent characteristics, CO…

Unveiling microbial structures during raw microalgae digestion and co-digestion with primary sludge to produce biogas using semi-continuous AnMBR systems

[EN] Methane production from microalgae can be enhanced through anaerobic co-digestion with carbon-rich substrates and thus mitigate the inhibition risk associated with its low C:N ratio. Acclimated microbial communities for microalgae disruption can be used as a source of natural enzymes in bioenergy production. However, co-substrates with a certain microbial diversity such as primary sludge might shift the microbial structure. Substrates were generated in a Water Resource Recovery Facility (WRRF) and combined as follows: Scenedesmus or Chlorella digestion and microalgae co-digestion with primary sludge. The study was performed using two lab-scale Anaerobic Membrane Bioreactors (AnMBR). Du…

Use of neurofuzzy networks to improve wastewater flow-rate forecasting

A neurofuzzy wastewater flow-rate forecasting model (NFWFFM) has been developed and tested with actual data measured at the input of two wastewater treatment facilities which treat the wastewater corresponding to 150,000 and 1,250,000p.e., respectively. Good agreements between forecasted and actual flow-rates were obtained. The artificial intelligence algorithm uses only two input variables (day of the week and average daily flow-rate of day before) and one output variable (predicted average daily flow-rate). Using three months data for training the network, a long-term forecast (one month) is made with average errors below 10%. Results were compared with those obtained by applying the Cens…

Reliable method for assessing the COD mass balance of a submerged anaerobic membrane bioreactor (SAMBR) treating sulphate-rich municipal wastewater

The anaerobic treatment of sulphate-rich wastewater causes sulphate reducing bacteria (SRB) and methanogenic archaea (MA) to compete for the available substrate. The outcome is lower methane yield coefficient and, therefore, a reduction in the energy recovery potential of the anaerobic treatment. Moreover, in order to assess the overall chemical oxygen demand (COD) balance, it is necessary to determine how much dissolved CH4 is lost in the effluent. The aim of this study is to develop a detailed and reliable method for assessing the COD mass balance and, thereby, to establish a more precise methane yield coefficient for anaerobic systems treating sulphate-rich wastewaters. A submerged anaer…

Guidelines for alkylphenols estimation as alkylphenol polyethoxylates pollution indicator in wastewater treatment plant effluents

A solid-phase microextraction coupled with a gas chromatography-mass spectrometry method has been developed for the estimation of technical nonylphenol in the presence of other endocrine disruptors, belonging to different chemical families. The profile of the technical nonylphenol found in real samples was tested, and, given that it was similar to that provided for the standard used, reliable results were obtainable. Endocrine disruptors such as 4-n-nonylphenol, bisphenol A and 4-tert-octylphenol were simultaneously analysed. The best conditions achieved enabled the analysis of all analytes using a sample volume of 15 mL or even only 300 μL. Using such a low sample volume reduced the filtra…

Microbial community characterization during anaerobic digestion of Scenedesmus spp. under mesophilic and thermophilic conditions

[EN] Microbial communities were thoroughly characterized in a mesophilic anaerobic membrane bioreactor (AnMBR) and a thermophilic continuous stirred tank reactor (CSTR), which were both treating recalcitrant microalgal biomass dominated by Scenedesmus. 16S rRNA amplicon sequencing analysis was performed when the AnMBR achieved 70% algal biodegradation and revealed high microbial diversity, probably due to the high solid retention time (SRT) of the AnMBR configuration. The bacterial community consisted of Chloroflexi (27.9%), WWE1 (19.0%) and Proteobacteria (15.4%) as the major phyla, followed by Spirochaetes (7.7%), Bacteroidetes (5.9%) and Firmicutes (3.6%). These phyla are known to exhibi…

Mixed microalgae culture for ammonium removal in the absence of phosphorus: Effect of phosphorus supplementation and process modeling

Microalgal growth and ammonium removal in a P-free medium have been studied in two batch photobioreactors seeded with a mixed microalgal culture and operated for 46 days. A significant amount of ammonium (106 mg NH4-Nl(-1)) was removed in a P-free medium, showing that microalgal growth and phosphorus uptake are independent processes. The ammonium removal rate decreased during the experiment, partly due to a decrease in the cellular phosphorus content. After a single phosphate addition in the medium of one of the reactors, intracellular phosphorus content of the corresponding microalgal culture rapidly increased, and so did the ammonium removal rate. These results show how the amount of phos…

Application of the General Model "Biological Nutrient Removal Model No.1" to upgrade two full-scale WWTPs

In this paper, two practical case studies for upgrading two wastewater treatment plants (WWTPs) using the general model BNRM1 (Biological Nutrient Removal Model No. 1) are presented. In the first case study, the Tarragona WWTP was upgraded by reducing the phosphorus load to the anaerobic digester in order to minimize the precipitation problems. Phosphorus load reduction was accomplished by mixing the primary sludge and the secondary sludge and by elutriating the mixed sludge. In the second case study, the Alcantarilla WWTP, the nutrient removal was enhanced by maintaining a relatively low dissolved oxygen concentration in Stage A to maintain the acidogenic bacteria activity. The VFA produce…

Influence of food waste addition over microbial communities in an Anaerobic Membrane Bioreactor plant treating urban wastewater

[EN] Notorious changes in microbial communities were observed during and after the joint treatment of wastewater with Food Waste (FW) in an Anaerobic Membrane Bioreactor (AnMBR) plant. The microbial population was analysed by high-throughput sequencing of the 16S rRNA gene and dominance of Chloroflexi, Firmicutes, Synergistetes and Proteobacteria phyla was found. The relative abundance of these potential hydrolytic phyla increased as a higher fraction of FW was jointly treated. Moreover, whereas Specific Methanogenic Activity (SMA) rose from 10 to 51 mL CH4 g(-1) VS, Methanosarcinales order increased from 34.0% over 80.0% of total Archaea, being Methanosaeta the dominant genus. The effect o…

Treatment of a submerged anaerobic membrane bioreactor (SAnMBR) effluent by an activated sludge system: the role of sulphide and thiosulphate in the process.

This work studies the use of a well-known and spread activated sludge system (UCT configuration) to treat the effluent of a submerged anaerobic membrane bioreactor (SAnMBR) treating domestic waste-water. Ammonia, phosphate, dissolved methane and sulphide concentrations in the SAnMBR effluent were around 55 mg NH4-N L-1, 7 mg PO4-P L-1, 30 mg non-methane biodegradable COD L-1, and 105 mg S2- L-1 respectively. The results showed a nitrification inhibition caused by the presence of sulphur compounds at any of the solids retention time (SRT) studied (15,20 and 25 days). This inhibition could be overcome increasing the hydraulic retention time (HRT) from 13 to 26 h. Among the sulphur compounds, …

Selecting the most suitable microalgae species to treat the effluent from an anaerobic membrane bioreactor.

[EN] Conventional treatments for nutrient removal in wastewater are shifting to Anaerobic Membrane Bioreactors, which produce a high-quality effluent with minimum sludge production. The effluent resulting contains high nitrogen and phosphorus load that can be eliminated by microalgae culture. The aim of this study is to evaluate the ammonium and phosphorus removal rate of different microalgae species in the effluent of an anaerobic treatment. For that, 4 different microalgae species have been tested (Chlamydomonas reinhardtii, Scenedesmus obliquus, Chlorella vulgaris and Monoraphidium braunii) in batch monoculture and mixed conditions. Results indicate that all species are able to eliminate…

Wastewater nutrient removal in a mixed microalgae-bacteria culture: effect of light and temperature on the microalgae-bacteria competition.

[EN] The aim of this study was to evaluate the effect of light intensity and temperature on nutrient removal and biomass productivity in a microalgae¿bacteria culture and their effects on the microalgae¿bacteria competition. Three experiments were carried out at constant temperature and various light intensities: 40, 85 and 125¿µE¿m¿2¿s¿1. Other two experiments were carried out at variable temperatures: 23¿±¿2°C and 28¿±¿2°C at light intensity of 85 and 125¿µE¿m¿2¿s¿1, respectively. The photobioreactor was fed by the effluent from an anaerobic membrane bioreactor. High nitrogen and phosphorus removal efficiencies (about 99%) were achieved under the following operating conditions: 85¿125¿µE¿…

Potential use of the organic fraction of municipal solid waste in anaerobic co-digestion with wastewater in submerged anaerobic membrane technology

Food waste was characterized for its potential use as substrate for anaerobic co-digestion in a submerged anaerobic membrane bioreactor pilot plant that treats urban wastewater (WW). 90% of the particles had sizes under 0.5 mm after grinding the food waste in a commercial food waste disposer. COD, nitrogen and phosphorus concentrations were 100, 2 and 20 times higher in food waste than their average concentrations in WW, but the relative flow contribution of both streams made COD the only pollutant that increased significantly when both substrates were mixed. As sulphate concentration in food waste was in the same range as WW, co-digestion of both substrates would increase the COD/SO4-S rat…

A review on anaerobic membrane bioreactors (AnMBRs) focused on modelling and control aspects

[EN] The use of anaerobic membrane bioreactor technology (AnMBR) is rapidly expanding. However, depending on the application, AnMBR design and operation is not fully mature, and needs further research to optimize process efficiency and enhance applicability. This paper reviews state-of-the-art of AnMBR focusing on modelling and control aspects. Quantitative environmental and economic evaluation has demonstrated substantial advantages in application of AnMBR to domestic wastewater treatment, but detailed modelling is less mature. While anaerobic process modelling is generally mature, more work is needed on integrated models which include coupling between membrane performance (including fouli…

Effect of pH on biological phosphorus uptake.

An anaerobic aerobic laboratory scale sequencing batch reactor (SBR) was operated to study the effect of pH on enhanced biological phosphorus removal. Seven steady states were achieved under different operating conditions. In all of them, a slight variation in the pH value was observed during anaerobic phase. However, pH rose significantly during aerobic phase. The increase observed was due to phosphorus uptake and carbon dioxide stripping. When pH was higher than 8.2-8.25 the phosphorus uptake rate clearly decreased. The capability of Activated Sludge Model No. 2d (ASM2d) and Biological Nutrient Removal Model No. 1 (BNRM1) to simulate experimental results was evaluated. Both models success…

Insights into the biological process performance and microbial diversity during thermophilic microalgae co-digestion in an anaerobic membrane bioreactor (AnMBR)

Abstract Harvested microalgae Chlorella spp. and primary sludge were co-digested in a laboratory-scale anaerobic membrane bioreactor (AnMBR) under thermophilic conditions (55 °C). The system was run for 700 days divided into four experimental phases to determine the influence of the organic loading rate on the process performance and the microbial community. The rise in organic loading rate from 0.17 to 0.5 gCOD·L−1·d−1 led to a 35% improvement in methane production. The system reached 69% biodegradability working at 0.5 gCOD·L−1·d−1 and a high solids retention time (70 d), indicating the efficient conversion of biomass into biogas through the AnMBR configuration while avoiding possible inh…

Single and competitive adsorption of Cd and Zn onto a granular activated carbon

Single and competitive adsorption of cadmium and zinc onto granular activated carbon DARCO 12–20 mesh has been investigated. This activated carbon has been shown as an effective adsorbent for both metals. Cadmium and zinc removals increased with pH and decreased with molar metal/carbon ratio. Surface precipitation phenomena have been detected for the higher pHs and molar ratios. The adsorption process has been modelled on the surface complexation Triple Layer Model (TLM). For this purpose, the amphoteric nature of the activated carbon has been studied. Single metal adsorption data have been used to calibrate TLM parameters. A dependence of the adsorption constants on pH and molar metal/carb…

Anaerobic membrane bioreactors for resource recovery from municipal wastewater: a comprehensive review of recent advances

[EN] In a paradigm shift towards a sustainable society based on the Circular Economy, wastewater treatments are rapidly evolving towards simultaneous recovery and reuse of clean water, renewable energy, and nutrients. This review examines recent advances (from 2016 to 2020) in the potential of anaerobic membrane bioreactors (AnMBRs) to serve as the core technology for municipal wastewater (MWW) resource recovery, focusing on the latest technological advances and economic and environmental innovation perspectives. The potentials and limitations of AnMBR for further full-scale application and new platforms to address these challenges are discussed, covering systems based on co-digestion, pre-…

Calibration and simulation of ASM2d at different temperatures in a phosphorous removal pilot plant

In this work, an organic and nutrient removal pilot plant was used to study the temperature influence on phosphorus accumulating organisms. Three experiments were carried out at 13, 20 and 24.5 degrees C, achieving a high phosphorus removal percentage in all cases. The ASM2d model was calibrated at 13 and 20 degrees C and the Arrhenius equation constant was obtained for phosphorus removal processes showing that the temperature influences on the biological phosphorus removal subprocesses in a different degree. The 24.5 degrees C experiment was simulated using the model parameters obtained by means of the Arrhenius equation. The simulation results for the three experiments showed good corresp…

Effect of long residence time and high temperature over anaerobic biodegradation of Scenedesmus microalgae grown in wastewater

[EN] Anaerobic digestion of indigenous Scenedesmus spp. microalgae was studied in continuous lab-scale anaerobic reactors at different temperatures (35 degrees C and 55 degrees C), and sludge retention time - SRT (50 and 70 days). Mesophilic digestion was performed in a continuous stirred-tank reactor (CSTR) and in an anaerobic membrane bioreactor (AnMBR). Mesophilic CSTR operated at 50 days SRT only achieved 11.9% of anaerobic biodegradability whereas in the AnMBR at 70 days SRT and 50 days HRT reached 39.5%, which is even higher than the biodegradability achieved in the thermophilic CSTR at 50 days SRT (30.4%). Microbial analysis revealed a high abundance of cellulose-degraders in both re…

Endocrine disrupter compounds removal in wastewater using microalgae: Degradation kinetics assessment

[EN] This paper describes a study carried out to determine the removal kinetics of four micropollutants (4-tert-octylphenol (OP), technical-nonylphenol (t-NP), 4-nonylphenol (4-NP) and bisphenol-A (BPA)) usually found in wastewater streams. The kinetic experiments were carried out in batch reactors containing the effluent of an Anaerobic Membrane BioReactor (AnMBR) in the presence of light, oxygen and microalgae. As the degradation process of the studied micropollutants obeyed a pseudo-first-order kinetics, the second-order kinetics for each micropollutant was then calculated. The second order rate constants for the hydroxyl radical (k.(OH)) ranged from 7.0.10(+10) to 6.6.10(+12) L.mol(-1).…

A methodology for sequencing batch reactor identification with artificial neural networks: A case study

This paper presents a systematic methodology based on the application of artificial neural networks for sequencing batch reactor (SBR) identification. The SBR is a fill-and-draw biological wastewater technology, which is specially suited for nutrient removal. The proposed approach makes optimal use of the available data during the training stage and it is aimed at achieving high generalization ability. For this purpose, a wide range of experimental conditions, including different solids retention times and influent characteristics, has been used. The methodology is successfully applied to develop a soft-sensor for monitoring a laboratory-scale SBR operated for enhanced biological phosphorus…

Mathematical modelling of filtration in submerged anaerobic MBRs (SAnMBRs): long-term validation

The aim of this study was the long-term validation of a model capable of reproducing the filtration process occurring in a submerged anaerobic membrane bioreactor (SAnMBR) system. The proposed model was validated using data obtained horn a SAnMBR demonstration plant fitted with industrial-scale hollow-fibre membranes. The validation was carried out using both lightly and heavily fouled membranes operating at different bulk concentrations, gas sparging intensities and transmembrane fluxes. Across a broad spectrum of operating conditions, the model correctly forecast the respective experimental data in the long term. The simulation results revealed the importance of controlling irreversible f…

Exploring the limits of anaerobic biodegradability of urban wastewater by AnMBR technology

[EN] Anaerobic membrane bioreactors (AnMBRs) can achieve maximum energy recovery from urban wastewater (UWW) by converting influent COD into methane. The aim of this study was to assess the anaerobic biodegradability limits of urban wastewater with AnMBR technology by studying the possible degradation of the organic matter considered as non-biodegradable as observed in aerobic membrane bioreactors operated at very high sludge retention times. For this, the results obtained in an AnMBR pilot plant operated at very high SRT (140 days) treating sulfate-rich urban wastewater were compared with those previously obtained with the system operating at lower SRT (29 to 70 days). At 140 days SRT the …

Dynamic Membranes for Enhancing Resources Recovery from Municipal Wastewater

[EN] This paper studied the feasibility of using dynamic membranes (DMs) to treat municipal wastewater (MWW). Effluent from the primary settler of a full-scale wastewater treatment plant was treated using a flat 1 mu m pore size open monofilament polyamide woven mesh as supporting material. Two supporting material layers were required to self-form a DM in the short-term (17 days of operation). Different strategies (increasing the filtration flux, increasing the concentration of operating solids and coagulant dosing) were used to enhance the required forming time and pollutant capture efficiency. Higher permeate flux and increased solids were shown to be ineffective while coagulant dosing sh…

Using SOM and PCA for analysing and interpreting data from a P-removal SBR

This paper focuses on the application of Kohonen self-organizing maps (SOM) and principal component analysis (PCA) to thoroughly analyse and interpret multidimensional data from a biological process. The process is aimed at enhanced biological phosphorus removal (EBPR) from wastewater. In this work, SOM and PCA are firstly applied to the data set in order to identify and analyse the relationships among the variables in the process. Afterwards, K-means algorithm is used to find out how the observations can be grouped, on the basis of their similarity, in different classes. Finally, the information obtained using these intelligent tools is used for process interpretation and diagnosis. In the…

Nitrite inhibition of microalgae induced by the competition between microalgae and nitrifying bacteria

[EN] Outdoor microalgae cultivation systems treating anaerobic membrane bioreactor (AnMBR) effluents usually present ammonium oxidising bacteria (AOB) competition with microalgae for ammonium uptake, which can cause nitrite accumulation. In literature, nitrite effects over microalgae have shown controversial results. The present study evaluates the nitrite inhibition role in a microalgae-nitrifying bacteria culture. For this purpose, pilot- and lab-scale assays were carried out. During the continuous outdoor operation of the membrane photobioreactor (MPBR) plant, biomass retention time (BRT) of 2 d favoured AOB activity, which caused nitrite accumulation. This nitrite was confirmed to inhib…

Design of nutrient removal activated sludge systems

A mechanistic mathematical model for nutrient and organic matter removal was used to describe the behavior of a nitrification denitrification enhanced biological phosphorus removal (NDEBPR) system. This model was implemented in a user-friendly software DESASS (design and simulation of activated sludge systems). A 484-L pilot plant was operated to verify the model results. The pilot plant was operated for three years over three different sludge ages. The validity of the model was confirmed with data from the pilot plant. Also, the utility of DESASS as a valuable tool for designing NDEBPR systems was confirmed.

Phosphorus recovery by struvite crystallization in WWTPs: Influence of the sludge treatment line operation

Phosphorus recovery by struvite (MgNH(4)PO(4).6H(2)O) crystallization is one of the most widely recommended technologies for treating sludge digester liquors especially in wastewater treatments plants (WWTP) with enhanced biological phosphorus removal (EBPR). In this paper, phosphorus recovery by struvite crystallization is assessed using the rejected liquors resulting from four different operational strategies of the sludge treatment line. Phosphorus precipitation and recovery efficiencies of between 80-90% and 70-85%, respectively, were achieved in the four experiments. The precipitates formed were mainly struvite, followed by amorphous calcium phosphate and, in some experiments, by calci…

Effect of pH, cation concentration and sorbent concentration on cadmium and copper removal by a granular activated carbon

The single adsorption of cadmium and copper from aqueous solutions has been investigated on Darco 12-20 mesh granular activated carbon for a wide range of experimental conditions: pH, metal concentration and carbon concentration. The results showed the efficiency of the activated carbon as sorbent for both metals. Metal removal increases on raising pH and carbon concentration, and decreases on raising the initial metal concentration. The adsorption processes have been modelled using the surface complex formation (SCF) Triple Layer Model (TLM) with a single surface bidentate species or with an overall surface species with fractional stoichiometry. Bidentate stoichiometry considering pH, meta…

Detection and prevention of enhanced biological phosphorus removal deterioration caused by Zoogloea overabundance.

A sequencing batch reactor was operated in the conventional anaerobic-aerobic mode for enhanced biological phosphorus removal using acetate as the sole substrate. Despite the nutrients concentrations in the influent being high enough to satisfy the biological requirements, Zoogloea ramigera managed to grow in the system until it had negative effects on the process performance. The excess of exocellular polymeric material produced by this microorganism contributed to a viscous bulking phenomenon and caused important settling problems. The examination of the sludge under the microscope was a valuable tool to diagnose the cause of the imbalance in the process. The strategy adopted to avoid the…

DSC: software tool for simulation-based design of control strategies applied to wastewater treatment plants.

This paper presents a computer tool called DSC (Simulation based Controllers Design) that enables an easy design of control systems and strategies applied to wastewater treatment plants. Although the control systems are developed and evaluated by simulation, this tool aims to facilitate the direct implementation of the designed control system to the PC of the full-scale WWTP (wastewater treatment plants). The designed control system can be programmed in a dedicated control application and can be connected to either the simulation software or the SCADA of the plant. To this end, the developed DSC incorporates an OPC server (OLE for process control) which facilitates an open-standard communic…

Energy and environmental impact of an anaerobic membrane bioreactor (AnMBR) demonstration plant treating urban wastewater

Abstract In order to assess the environmental feasibility of anaerobic membrane bioreactor (AnMBR) technology for urban wastewater (UWW) treatment at ambient temperature, a demonstration plant was operated within the LIFE MEMORY project ( http://www.life-memory.eu/en/ ). This plant incorporates full-scale hollow-fiber membrane modules and was fed with the effluent from the pre-treatment of the “Alcazar de San Juan” WWTP (Alcazar de San Juan, Ciudad Real, Spain). Because of the dimensions of this plant, the system can be regarded as a previous step to the scale-up of AnMBR technology for full-scale UWW treatment. High-energy recovery potentials were achieved treating medium-/high-loaded UWW …

AnMBR, reclaimed water and fertigation: Two case studies in Italy and Spain to assess economic and technological feasibility and CO2 emissions within the EU Innovation Deal initiative

[EN] The use of anaerobic membrane bioreactor (AnMBR) technology on urban wastewater can help to alleviate droughts, by reusing the water and nutrients embedded in the effluent in agriculture (fertigation) in line with Circular Economy principles. The combination of AnMBR and fertigation reduces CO2 emissions due to the organic matter valorization and the partial avoidance of mineral fertilizer requirements. However, both AnMBR and fertigation still face technological and regulatory barriers that need to be overcome. These bottlenecks were tackled within the first Innovation Deal approved by the European Commission in 2016, and gave rise to several case studies on water reuse systems. The r…

Microalgae cultivation in wastewater: nutrient removal from anaerobic membrane bioreactor effluent

This study investigated the removal of nitrogen and phosphorus from the effluent of a submerged anaerobic membrane bioreactor (SAnMBR) by means of a lab-scale photobioreactor in which algae biomass was cultured in a semi-continuous mode for a period of 42 days. Solids retention time was 2 days and a stable pH value in the system was maintained by adding CO2. Nitrogen and phosphorus concentrations in the SAnMBR effluent fluctuated according to the operating performance of the bioreactor and the properties of its actual wastewater load. Despite these variations, the anaerobic effluent proved to be a suitable growth medium for microalgae (mean biomass productivity was 234 mgl(-1) d(-1)), achie…

Calcium effect on enhanced biological phosphorus removal.

The role of calcium (Ca) in enhanced biological phosphorus removal and its possible implications on the metabolic pathway have been studied. The experience has been carried out in an SBR under anaerobic–aerobic conditions for biological phosphorus removal during 8 months. The variations of influent Ca concentration showed a clear influence on the EBPR process, detecting significant changes in YPO4. These YPO4 variations were not due to influent P/COD ratio, pH, denitrification and calcium phosphate formation. The YPO4 has been found to be highly dependent on the Ca concentration, increasing as Ca concentration decreases. The results suggest that high Ca concentrations produce “inert” granul…

Fate of endocrine disruptor compounds in an anaerobic membrane bioreactor (AnMBR) coupled to an activated sludge reactor

[EN] The occurrence and fate of three groups of micropollutants - alkylphenols, pentachlorophenol and hormones - were studied in a pilot plant consisting of an anaerobic membrane bioreactor (AnMBR) coupled to an activated sludge reactor (University of Cape Town configuration - UCT). Under anaerobic conditions, the octylphenol and technical-nonylphenol soluble concentrations increased producing negative degradation ratios (i.e., -175 and -118%, respectively). However, high 4-n-nonylphenol and bisphenol-A degradation ratios (92 and 59% for 4-n-nonylphenol and bisphenol-A, respectively) as well as complete pentachlorophenol, estrone, 17 beta-estradiol and 17 alpha-ethinylestradiol removal were…

Interactions between calcium precipitation and the polyphosphate-accumulating bacteria metabolism

A sequencing batch reactor that is operated for biological phosphorus removal has been operated under different influent calcium concentrations to study the precipitation process and the possible effects of phosphorus precipitation in the biological phosphorus removal process. Four experiments were carried out under different influent calcium concentrations ranging from 10 to 90 g Ca m(-3). The experimental results and the equilibrium study, which are based on the saturation index calculation, confirm that the process controlling the calcium behaviour is the calcium phosphate precipitation. This precipitation takes place at two stages: initially, precipitation of the amorphous calcium phosp…

A modification to the Activated Sludge Model No. 2 based on the competition between phosphorus-accumulating organisms and glycogen-accumulating organisms

A modification to the ASM2 is proposed which permits representation of the competition between phosphorus accumulating organisms (PAOs) and glycogen accumulating organisms (GAOs) in a nutrient removal activated sludge system. Some important aspects, which are not considered in ASM2, are discussed. The proposed modification includes denitrification by PAOs, PAO glycogen storage capability and GAO metabolism model. It is shown that the proposed modification is capable of describing pilot plant data using a single set of stoichiometric and kinetic parameters over three different sludge ages (16, 14 and 12 days). The modified ASM2 may be applicable to a wide range of situations where PAOs and G…

Wastewater COD characterization: analysis of respirometric and physical-chemical methods for determining biodegradable organic matter fractions

BACKGROUND: In this work, a comprehensive study of the respirometric and physical–chemical methods has been performed to evaluate the information provided by these two methodologies in order to assess the biodegradable organic matter fractions of wastewater. RESULTS: First, an analysis was performed of the influence of the initial substrate on biomass ratio (F0/X0) in the assessment of readily biodegradable organic matter, SS, through respirometric experiments. In order to achieve an adequate assessment of the SS component, similar conditions (given by the initial F0/X0 ratio) must be employed in experiments that are carried to determine SS and YH (heterotrophic yield). Second, a comparativ…

Filtration process cost in submerged anaerobic membrane bioreactors (AnMBRs) for urban wastewater treatment

[EN] The objective of this study was to evaluate the effect of the main factors affecting the cost of the filtration process in submerged anaerobic membrane bioreactors (AnMBRs) for urban wastewater (UWW) treatment. Experimental data for CAPEX/OPEX calculations was obtained in an AnMBR system featuring industrial-scale hollow-fiber (HF) membranes. Results showed that operating at J(20) slightly higher than the critical flux results in minimum CAPEX/OPEX. The minimum filtration process cost ranged from Euro0.03 to Euro0.12 per m(3), mainly depending on SGD(m) (from 0.05 to 0.3 m(3)m(-2)h(-1)) and MLSS (from 5 to 25 gL-1). The optimal SGD(m) resulted in approx. 0.1 m(3)m(-2)h(-1).

Micropollutants removal in an anaerobic membrane bioreactor and in an aerobic conventional treatment plant

The paper expresses an attempt to tackle the problem due to the presence of micropollutants in wastewater which may be able to disrupt the endocrine system of some organisms. These kinds of compounds are ubiquitously present in municipal wastewater treatment plant (WWTP) effluents. The aim of this paper is to compare the fate of the alkylphenols-APs (4-(tert-octyl)) phenol, t-nonylphenol and 4-p-nonylphenol and the hormones (estrone, 17ß-estradiol and 17¿-ethinylestradiol) in a submerged anaerobic membrane bioreactor (SAMBR) pilot plant and in a conventional activated sludge wastewater treatment plant (CTP). The obtained results are also compared with the results obtained in a previous stud…

Calibration and validation of activated sludge model No.2d for Spanish municipal wastewater.

Activated Sludge Model No. 2d (ASM2d) was validated with data obtained from pilot scale plant treating municipal wastewater from the city of Valencia (Spain). First of all, ASM2d was calibrated using experimental data from anaerobic, anoxic and aerobic batches. A set of kinetic and stoichiometric parameters resulted from these assays. Differences between the values obtained and default values proposed in ASM2d can be explained by the presence of glycogen accumulating organisms (GAOs). The calibrated model was then used to simulate results from a pilot plant. Simulation using the set of parameters obtained accurately reproduces experimental results. This paper also presents a detailed proced…

Diagnosis of boron, fluorine, lead, nickel and zinc toxicity in citrus plantations in Villarreal, Spain

In the late 1980s, citrus plantations in the area of Villarreal (Spain) showed injuries similar to those previously reported for boron and fluorine toxicity. The area was affected by the disposal of industrial wastewater, mainly from ceramic industries. Conjunctive uses of surface water, groundwater and wastewater for irrigation had taken place. A survey was conducted at 25 orchards to assess leaves and soil for their boron, fluorine, lead, nickel and zinc contents. Wastewater and groundwater were also analyzed to corroborate the presence of these pollutants. The results showed that both boron and fluorine contents were greater than those reported as excess at the most part of the orchards …

Anaerobic membrane bioreactor (AnMBR) scale-up from laboratory to pilot-scale for microalgae and primary sludge co-digestion: Biological and filtration assessment

This research work proposes the scale-up evaluation in terms of biological and filtration performance from laboratory to pilot-scale of an anaerobic membrane bioreactor (AnMBR) co-digesting raw microalgae and primary sludge. Best operating conditions for this scale-up were energetically and economically assessed based on laboratory results. Economic balance showed 3% higher annual costs when operating a reactor at 100 d solids retention time (SRT) compared to 70 d SRT. Energetic balance showed a 5.5-fold increase in heat demand working at thermophilic temperature comparing to mesophilic. The AnMBR operating conditions were set at 70 d SRT and 35 °C. The pilot-scale and lab-scale co-digester…

Assessing and modeling nitrite inhibition in microalgae-bacteria consortia for wastewater treatment by means of photo-respirometric and chlorophyll fluorescence techniques

Abstract Total nitrite (TNO2 = HNO2 + NO−2) accumulation due to the activity of ammonia-oxidizing bacteria (AOB) was monitored in microalgae-bacteria consortia, and the inhibitory effect of nitrite/free nitrous acid (NO2-N/FNA) on microalgae photosynthesis and inhibition mechanism was studied. A culture of Scenedesmus was used to run two sets of batch reactors at different pH and TNO2 concentrations to evaluate the toxic potential of NO2-N and FNA. Photo-respirometric tests showed that NO2-N accumulation has a negative impact on net oxygen production rate (OPRNET). Chlorophyll a fluorescence analysis was used to examine the biochemical effects of NO2-N stress and the mechanism of NO2-N inhi…

An advanced control strategy for biological nutrient removal in continuous systems based on pH and ORP sensors

[EN] A fuzzy logic-based control system that uses low-cost sensors for controlling and optimizing the biological nitrogen removal in continuous systems has been developed. The novelty of this control system is the use of several pH, ORP, and dissolved oxygen (DO) sensors instead of on-line nitrogen sensors/analyzers. The nitrogen control system was developed and implemented in a UCT pilot plant fed with wastewater from a full-scale plant. The developed nitrification controller allows the effluent ammonium concentration to be maintained below the effluent criteria discharge with the minimum energy consumption. The denitrification process controller allows the energy consumption derived from …

Real-time optimization of the key filtration parameters in an AnMBR: Urban wastewater mono-digestion vs. co-digestion with domestic food waste

[EN] This study describes a model-based method for real-time optimization of the key filtration parameters in a submerged anaerobic membrane bioreactor (AnMBR) treating urban wastewater (UWW) and UWW mixed with domestic food waste (FW). The method consists of an initial screening to find out adequate filtration conditions and a real-time optimizer applied to a periodically calibrated filtration model for minimizing the operating costs. The initial screening consists of two statistical analyses: (1) Morris screening method to identify the key filtration parameters; (2) Monte Carlo method to establish suitable initial control inputs values. The operating filtration cost after implementing the…

Acclimatised rumen culture for raw microalgae conversion into biogas: Linking microbial community structure and operational parameters in anaerobic membrane bioreactors (AnMBR)

[EN] Ruminal fluid was inoculated in an Anaerobic Membrane Reactor (AnMBR) to produce biogas from raw Scenedesmus. This work explores the microbial ecology of the system during stable operation at different solids retention times (SRT). The 16S rRNA amplicon analysis revealed that the acclimatised community was mainly composed of Anaerolineaceae, Spirochaetaceae, Lentimicrobiaceae and Cloacimonetes fermentative and hydrolytic members. During the highest biodegradability achieved in the AnMBR (62%) the dominant microorganisms were Fervidobacterium and Methanosaeta. Different microbial community clusters were observed at different SRT conditions. Interestingly, syntrophic bacteria Gelria and …

A software for the integrated design of wastewater treatment plants

Abstract A software package has been developed for automated design of wastewater treatment plants. A user-friendly environment has been implemented to facilitate design tasks, allowing rapid evaluation of different alternatives as well as performing sensitivity analyses. Flexible treatment plant configurations can be established with preliminary, primary, biological and tertiary wastewater treatments, and sludge treatment units. A generalized steady-state model developed for biological processes is also included. The design process includes treatment units sizing, plant layout, hydraulic profile calculation and equipment assignment. The system capabilities for designing new plants and upgr…

Influence of sludge age on enhanced phosphorus removal in biological systems

The phosphorus removal process was studied in a bench-scale plant for a period of 300 days. The process was observed to depend greatly on two parameters: the amount of volatile fatty acid (VFA) taken up in the anaerobic stage and sludge age. For a given sludge age, phosphorus release versus VFA uptake in the anaerobic stage could be fitted to a straight line, while phosphorus uptake in the non-anaerobic stages fitted a logarithmic curve. Thus, phosphorus removal occurred within a limited VFA uptake range. The range width and the phosphorus removal capacity varied with sludge age.

Thermophilic anaerobic conversion of raw microalgae: Microbial community diversity in high solids retention systems

[EN] The potential of microbial communities for efficient anaerobic conversion of raw microalgae was evaluated in this work. A long-term operated thermophilic digester was fed with three different Organic Loading Rates (OLR) (0.2, 0.3 and 0.4¿g·L¿1·d¿1) reaching 32¿41% biodegradability values. The microbial community analysis revealed a remarkable presence of microorganisms that exhibit high hydrolytic capabilities such as Thermotogae (~44.5%), Firmicutes (~17.6%) and Dictyoglomi, Aminicenantes, Atribacteria and Planctomycetes (below ~5.5%) phyla. The suggested metabolic role of these phyla highlights the importance of protein hydrolysis and fermentation when only degrading microalgae. The …

Real-time control strategy for nitrogen removal via nitrite in a SHARON reactor using pH and ORP sensors

This paper presents a real-time control strategy for nitrogen removal via nitrite in a continuous flow SHARON reactor using on-line available and industrially feasible sensors (pH and ORP). The developed control strategy optimizes the length of aerobic and anoxic phases as well as the external carbon source addition. This strategy, implemented in a laboratory-scale SHARON reactor fed with synthetic wastewater and real dewatering sludge supernatant, was able to cope with step variations in influent flow rate and ammonium concentration. The main advantages of this control strategy over the traditional operation mode with fixed carbon source dosification and fixed length cycle operation were: …

Economic and environmental sustainability of submerged anaerobic MBR-based (AnMBR-based) technology as compared to aerobic-based technologies for moderate-/high-loaded urban wastewater treatment

[EN] The objective of this study was to assess the economic and environmental sustainability of submerged anaerobic membrane bioreactors (AnMBRs) in comparison with aerobic-based technologies for moderate-/high-loaded urban wastewater (UWW) treatment. To this aim, a combined approach of steady-state performance modelling, life cycle analysis (LCA) and life cycle costing (LCC) was used, in which AnMBR (coupled with an aerobic-based post-treatment) was compared to aerobic membrane bioreactor (AeMBR) and conventional activated sludge (CAS). AnMBR with CAS-based post-treatment for nutrient removal was identified as a sustainable option for moderate-/high-loaded UWW treatment: low energy consump…

An integral approach to sludge handling in a WWTP operated for EBPR aiming phosphorus recovery: simulation of alternatives, LCA and LCC analyses

[EN] As phosphorus is a non-renewable resource mainly used to produce fertilizers and helps to provide food all over the world, the proper management of its reserves is a global concern since it is expected to become scarcer in the near future. In this work we assessed two different sludge line configurations aiming for P extraction and recovery before anaerobic digestion and compared them with the classical configuration. This study has been performed by simulation with the model BNRM2 integrated in the software package DESASS 7.1. Configuration 1 was based on the production of a PO4-enriched stream from sludge via elutriation in the primary thickeners, while Configuration 2 was based on t…

Widening the applicability of AnMBR for urban wastewater treatment through PDMS membranes for dissolved methane capture: Effect of temperature and hydrodynamics.

[EN] AnMBR technology is a promising alternative to achieve future energy-efficiency and environmental-friendly urban wastewater (UWW) treatment. However, the large amount of dissolved methane lost in the effluent represents a potential high environmental impact that hinder the feasibility of this technology for full-scale applications. The use of degassing membranes (DM) to capture the dissolved methane from AnMBR effluents can be considered as an interesting alternative to solve this problem although further research is required to assess the suitability of this emerging technology. The aim of this study was to assess the effect of operating temperature and hydrodynamics on the capture of…

Effect of pH, substrate and free nitrous acid concentrations on ammonium oxidation rate.

Respirometric techniques have been used to determine the effect of pH, free nitrous acid (FNA) and substrate concentration on the activity of the ammonium oxidizing bacteria (AOB) present in an activated sludge reactor. With this aim, bacterial activity has been measured at different pH values (ranging from 6.2 to 9.7), total ammonium nitrogen concentrations (ranging from 0.1 to 10 mg TAN L-1) and total nitrite concentrations (ranging from 3 to 43 mg NO2-N L-1). According to the results obtained, the most appropriate kinetic expression for the growth of AOB in activated sludge reactors has been established. Substrate half saturation constant and FNA and pH inhibition constants have been obt…

A plant-wide energy model for wastewater treatment plants: application to anaerobic membrane bioreactor technology

[EN] The aim of this study is to propose a detailed and comprehensive plant-wide model for assessing the energy demand of different wastewater treatment systems (beyond the traditional activated sludge) in both steady- and unsteady-state conditions. The proposed model makes it possible to calculate power and heat requirements (W and Q, respectively), and to recover both power and heat from methane and hydrogen capture. In order to account for the effect of biological processes on heat requirements, the model has been coupled to the extended version of the BNRM2 plant-wide mathematical model, which is implemented in DESSAS simulation software. Two case studies have been evaluated to assess t…

Effect of sludge age on microbial consortia developed in MFCs

BACKGROUND This work is focused on the assessment of the performance of mini-scale air-breathing microbial fuel cells (MFCs), by monitoring the evolution of the bio-electrogenic activity for a period of 40 days and by comparing the microorganisms populations developed in each of the MFC after this period. RESULTS Five MFCs were operated at sludge ages ranging from 1.4 to 10.0 days. Results showed the superb performance of the MFC operating under a sludge age of 2.5 days. Desulfuromonas, Syntrophothermus, Solitalea, Acholeplasma, Propionicimonas, Desulfobacula and Sphaerochaeta are proposed as potential responsible for the bio-electrogenic activity. CONCLUSIONS Microbial population analysis …

MAB2.0 project: Integrating algae production into wastewater treatment

Abstract Different species of microalgae are highly efficient in removing nutrients from wastewater streams and are able to grow using flue gas as a CO2 source. These features indicate that application of microalgae has a promising outlook in wastewater treatment. However, practical aspects and process of integration of algae cultivation into an existing wastewater treatment line have not been investigated. The Climate-KIC co-funded Microalgae Biorefinery 2.0 project developed and demonstrated this integration process through a case study. The purpose of this paper is to introduce this process by phases and protocols, as well as report on the challenges and bottlenecks identified in the cas…

Study of the influence of temperature and precipitations on the levels of BTEX in natural waters.

Assessment of seasonal changes in surface water quality is an important aspect for evaluating temporal variation of water due to natural or anthropogenic inputs of point and non-point sources. The objective of this paper was to investigate the influence of seasonal temperature fluctuations and precipitations on the levels of BTEX in natural waters. Principal component analysis (PCA) was used to evaluate the seasonal correlations of BTEX levels in water and to extract the parameters that are most important in assessing seasonal variations of water quality. This study was carried out as a part of VOCs monitoring program in natural water samples from Mediterranean coast. To carry out this proj…

Economic and environmental sustainability of an AnMBR treating urban wastewater and organic fraction of municipal solid waste

[EN] The objective of this study was to evaluate the economic and environmental sustainability of a sub- merged anaerobic membrane bioreactor (AnMBR) treating urban wastewater (UWW) and organic fraction of municipal solid waste (OFMSW) at ambient temperature in mild/hot climates. To this aim, power requirements, energy recovery from methane (biogas methane and methane dissolved in the effluent), consumption of reagents for membrane cleaning, and sludge handling (polyelectrolyte and energy consumption) and disposal (farmland, landfilling and incineration) were evaluated within different operating scenarios. Results showed that, for the operating conditions considered in this study, AnMBR tec…

Design methodology for submerged anaerobic membrane bioreactors (AnMBR): A case study

[EN] The main objective of this study is to propose guidelines for designing submerged anaerobic MBR (AnMBR) technology for municipal wastewater treatment. The design methodology was devised on the basis of simulation and experimental results from an AnMBR plant featuring industrial-scale hollow-fibre membranes. The proposed methodology aims to minimise both capital expenditure and operating expenses, and the key parameters considered were: hydraulic retention time, solids retention time, mixed liquor suspended solids concentration in the membrane tank, 20 C-standardised critical flux, specificgas demand per square metre of membrane area, and flow of sludge being recycled from the membrane …

An improved sampling strategy based on trajectory design for application of the Morris method to systems with many input factors

[EN] In this paper, a revised version of the Morris approach, which includes an improved sampling strategy based on trajectory design, has been adapted to the screening of the most influential parameters of a fuzzy controller applied to WWTPs. Due to the high number of parameters, a systematic approach has been proposed to apply this improved sampling strategy with low computational demand. In order to find out the proper repetition number of elementary effects of each input factor on model output (EEi) calculations, an iterative and automatic procedure has been applied. The results show that the sampling strategy has a significant effect on the parameter significance ranking and that rando…

Adsorption of Heavy Metals from Aqueous Solutions onto Activated Carbon in Single Cu and Ni Systems and in Binary Cu-Ni, Cu-Cd and Cu-Zn Systems

Single copper and nickel adsorption from aqueous solutions onto a granular activated carbon is reported. Metal removals increase on raising pH and temperature, and decrease on raising the initial metal concentration at constant carbon dose. The adsorption processes are modelled using the surface complex formation (SCF) Triple Layer Model (TLM) with an overall surface bidentate species. A dependence of the SCF constant on pH, initial molar metal/carbon ratio and temperature is observed, and a correlation for log Kads is determined. The SCF model successfully predicts copper and nickel removals in single metal solutions. Adsorption in the binary metal systems copper–nickel, copper–cadmium and…

Global sensitivity and uncertainty analysis of a microalgae model for wastewater treatment.

The results of a global sensitivity and uncertainty analysis of a microalgae model applied to a Membrane Photobioreactor (MPBR) pilot plant were assessed. The main goals of this study were: (I) to identify the sensitivity factors of the model through the Morris screening method, i.e. the most influential factors; (II) to calibrate the influential factors online or offline; and (III) to assess the model's uncertainty. Four experimental periods were evaluated, which encompassed a wide range of environmental and operational conditions. Eleven influential factors (e.g. maximum specific growth rate, light intensity and maximum temperature) were identified in the model from a set of 34 kinetic pa…

Effect of temperature on ammonium removal in Scenedesmus sp

The effect of temperature on microalgal ammonium uptake was investigated by carrying out four batch experiments in which a mixed culture of microalgae, composed mainly of Scenedesmus sp., was cultivated under different temperatures within the usual temperature working range in Mediterranean climate (15-34 ºC). Ammonium removal rates increased with temperature up to 26 ºC and stabilized thereafter. Ratkowsky and Cardinal Temperatures models successfully reproduced the experimental data. Optimum (31.3 ºC), minimum (8.8 ºC) and maximum (46.1 ºC) temperatures for ammonium removal by Scenedesmus sp. under the studied conditions were obtained as model parameters. These temperature-related paramet…

Effect of pH and HNO2 concentration on the activity of ammonia-oxidizing bacteria in a partial nitritation reactor

Ammonia-oxidizing bacteria (AOB) are very sensitive to environmental conditions and wastewater treatment plant operational parameters. One of the most important factors affecting their activity is pH. Its effect is associated with: NH3/NH4 þ and HNO2/NO2 chemical equilibriums and biological reaction rates. The aim of this study was to quantify and model the effect of pH and free nitrous acid (FNA) concentration on the activity of AOB present in a lab-scale partial nitritation reactor. For this purpose, two sets of batch experiments were carried out using biomass from this reactor. Fluorescent in situ hybridization analysis showed that Nitrosomona eutropha and Nitrosomona europaea species we…

Modelling hydrolysis: Simultaneous versus sequential biodegradation of the hydrolysable fractions

Hydrolysis is considered the limiting step during solid waste anaerobic digestion (including co-digestion of sludge and biosolids). Mechanisms of hydrolysis are mechanistically not well understood with detrimental impact on model predictive capability. The common approach to multiple substrates is to consider simultaneous degradation of the substrates. This may not have the capacity to separate the different kinetics. Sequential degradation of substrates is theoretically supported by microbial capacity and the composite nature of substrates (bioaccessibility concept). However, this has not been experimentally assessed. Sequential chemical fractionation has been successfully used to define i…

Global sensitivity analysis of a filtration model for submerged anaerobic membrane bioreactors (AnMBR)

The results of a global sensitivity analysis of a filtration model for submerged anaerobic MBRs (AnMBRs) are assessed in this paper. This study aimed to (1) identify the less- (or non-) influential factors of the model in order to facilitate model calibration and (2) validate the modelling approach (i.e. to determine the need for each of the proposed factors to be included in the model). The sensitivity analysis was conducted using a revised version of the Morris screening method. The dynamic simulations were conducted using long-term data obtained from an AnMBR plant fitted with industrial-scale hollow-fibre membranes. Of the 14 factors in the model, six were identified as influential, i.e…

Performance of an outdoor membrane photobioreactor for resource recovery from anaerobically treated sewage

[EN] The objective of this work was to evaluate the performance of a pilot scale membrane photobioreactor (MPBR) for treating the effluent of an anaerobic membrane bioreactor (AnMBR) system. In particular, new experimental data on microalgae productivity, nutrient recovery, CO2 biofixation and energy recovery potential was obtained under different operating conditions, which would facilitate moving towards cost-effective microalgae cultivation on wastewater. To this aim, a 2.2-m(3) MPBR equipped with two commercial-scale hollow-fibre ultrafiltration membrane modules was operated treating the nutrient-loaded effluent from an AnMBR for sewage treatment. The influence of several design, enviro…

Comprehensive assessment of the microalgae-nitrifying bacteria competition in microalgae-based wastewater treatment systems: Relevant factors, evaluation methods and control strategies

[EN] Due to their capacity to assimilate carbon dioxide and nutrients, microalgae-based cultivation systems have emerged as a green solution for intensive wastewater treatment. However, when large concentrations of ammonium are present the competition between microalgae and ammonium-oxidising bacteria plays a significant role. Microalgae use ammonium to synthesise proteins, photosynthetic pigments and nucleic acids, while ammonium-oxidising bacteria use it as a source of electrons and oxidise it to nitrite.Several authors have studied the isolated factors that influence microalgae-nitrifying bacteria competition, although a comprehensive analysis of this interesting topic is still lacking. …

Nitrogen recovery using a membrane contactor: Modelling nitrogen and pH evolution

[EN] A hollow fibre membrane contactor has been applied for nitrogen recovery from anaerobic digestion supernatant at different operating conditions obtaining nitrogen recovery efficiencies over 99 %. A mathematical model able to represent the time evolution of pH and nitrogen concentration during the recovery process is presented in this paper. The developed model accurately reproduced the results obtained in 26 experiments carried out at different pH values (from 9 to 11), temperatures (from 25 to 35 degrees C), membrane surfaces (from 1.2 to 2.4 m(2)) and feed flow rates (from 0.33 x 10(-5) to 5.83 x 10(-5) m(3)/s) predicting the variations in nitrogen recovery rates measured at the diff…

Methane recovery efficiency in a submerged anaerobic membrane bioreactor (SAnMBR) treating sulphate-rich urban wastewater: Evaluation of methane losses with the effluent

The present paper presents a submerged anaerobic membrane bioreactor (SAnMBR) as a sustainable approach for urban wastewater treatment at 33 and 20 C, since greenhouse gas emissions are reduced and energy recovery is enhanced. Compared to other anaerobic systems, such as UASB reactors, the membrane technology allows the use of biogas-assisted mixing which enhances the methane stripping from the liquid phase bulk. The methane saturation index obtained for the whole period (1.00 ± 0.04) evidenced that the equilibrium condition was reached and the methane loss with the effluent was reduced. The methane recovery efficiency obtained at 20 C (53.6%) was slightly lower than at 33 C (57.4%) due to …

PDMS membranes for feasible recovery of dissolved methane from AnMBR effluents

[EN] This study aimed to evaluate the feasibility of degassing membrane (DM) technology for recovering dissolved methane from AnMBR effluents. For that purpose, a PDMS membrane module was operated for treating the effluent from an AnMBR prototype-plant, which treated urban wastewater (UWW) at ambient temperature. Different transmembrane pressures and liquid flow rates were applied for evaluating methane recovery efficiency. Maximum methane recoveries were achieved when increasing the vacuum pressure and reducing the liquid flow rate, reaching a maximum methane recovery efficiency of around 80% at a transmembrane pressure (TMP) of 0.8 bars and a treatment flow rate (Q(L)) of 50 L h(-1). The …

The operating cost of an anaerobic membrane bioreactor (AnMBR) treating sulphate-rich urban wastewater

The objective of this study was to evaluate the operating cost of an anaerobic membrane bioreactor (AnMBR) treating sulphate-rich urban wastewater (UWW) at ambient temperature (ranging from 17 to 33 degrees C). To this aim, energy consumption, methane production, and sludge handling and recycling to land were evaluated. The results revealed that optimising specific gas demand with respect to permeate volume (SGDp) and sludge retention time (for given ambient temperature conditions) is essential to maximise energy savings (minimum energy demand: 0.07 kW h m(-3)). Moreover, low/moderate sludge productions were obtained (minimum value: 0.16 kg TSS kg(-1) CODRemoved), which further enhanced the…

Optimum design and operation of primary sludge fermentation schemes for volatile fatty acids production.

This paper presents a model-knowledge based algorithm for optimising the primary sludge fermentation process design and operation. This is a recently used method to obtain the volatile fatty acids (VFA), needed to improve biological nutrient removal processes, directly from the raw wastewater. The proposed algorithm consists in a heuristic reasoning algorithm based on the expert knowledge of the process. Only effluent VFA and the sludge blanket height (SBH) have to be set as design criteria, and the optimisation algorithm obtains the minimum return sludge and waste sludge flow rates which fulfil those design criteria. A pilot plant fed with municipal raw wastewater was operated in order to …

Outdoor microalgae-based urban wastewater treatment: recent advances, applications and future perspectives

[EN] Although microalgae-based wastewater treatment has been traditionally carried out in extensive waste stabilization ponds, recent trends focus on the use of microalgae to apply the circular economy principles in the wastewater treatment sector due to the capacity of algae to absorb carbon dioxide while recovering nutrients from sewage. To this aim, the development of new intensive microalgae-based systems with higher efficiency and level of process control is required. Results obtained for these systems at lab scale are generally promising. However, upscaling to outdoor conditions is often uncertain. Some advances have been made in terms of applying open systems at large scale. However,…

Fermentation and elutriation of primary sludge: Effect of SRT on process performance

Abstract A primary sludge fermentation–elutriation pilot plant was operated using in-line and side-stream schemes. The influence of solids retention time, recirculation sludge flow-rate and solids concentration on the fermentation–elutriation process performance has been assessed in this paper. The use of high elutriation flows (12% of influent flow) improved the volatile fatty acids (VFA) concentration in the effluent stream. Suspended solids removal efficiency decreased in the primary settler when the solids retention time (SRT) was increased from 4 to 8 days. Disintegration step during hydrolysis process was pointed out as the main reason for that decrease. Maximum VFA productions were a…

Water resource recovery by means of microalgae cultivation in outdoor photobioreactors using the effluent from an anaerobic membrane bioreactor fed with pre-treated sewage.

[EN] With the aim of assessing the potential of microalgae cultivation for water resource recovery (WRR), the performance of three 0.55 m3 flat-plate photobioreactors (PBRs) was evaluated in terms of nutrient removal rate (NRR) and biomass production. The PBRs were operated outdoor (at ambient temperature and light intensity) using as growth media the nutrient-rich effluent from an AnMBR fed with pre-treated sewage. Solar irradiance was the most determining factor affecting NRR. Biomass productivity was significantly affected by temperatures below 20 °C. The maximum biomass productivity (52.3 mg VSS·L−1·d−1) and NRR (5.84 mg NH4-N·L−1·d−1 and 0.85 mg PO4-P·L−1·…

Anaerobic membrane bioreactors (AnMBR) treating urban wastewater in mild climates

[EN] Feasibility of an AnMBR demonstration plant treating urban wastewater (UWW) at temperatures around 25-30 degrees C was assessed during a 350-day experimental period. The plant was fed with the effluent from the pretreatment of a full-scale municipal WWTP, characterized by high COD and sulfate concentrations. Biodegradability of the UWW reached values up to 87%, although a portion of the biodegradable COD was consumed by sulfate reducing organisms. Effluent COD remained below effluent discharge limits, achieving COD removals above 90%. System operation resulted in a reduction of sludge production of 36-58% compared to theoretical aerobic sludge productions. The membranes were operated a…

A supervisory control system for optimising nitrogen removal and aeration energy consumption in wastewater treatment plants

A fuzzy logic supervisory control system for optimising nitrogen removal and aeration energy consumption has been developed. This control system allows optimising and controlling the dissolved oxygen (DO) concentration in the aerobic reactors, the blowers discharge pressure and the effluent ammonia and nitrate concentrations. DO is controlled by adjusting control valve opening and blower discharge pressure is controlled by modifying rotational speed of the blowers. Optimum nitrification/denitrification is achieved by modifying the DO set point in the last aerobic reactor and the internal recirculation. This system has been tested by simulation in a Bardenpho process using the Activated Slud…

Occurrence of priority pollutants in WWTP effluents and Mediterranean coastal waters of Spain

A comprehensive study aimed at evaluating the occurrence, significance of concentrations and spatial distribution of priority pollutants (PPs) along the Comunidad Valenciana coastal waters (Spain) was carried out in order to fulfil the European Water Framework Directive (WFD). Additionally, PP concentrations were also analysed in the effluent of 28 WWTPs distributed along the studied area. In coastal waters 36 organic pollutants of the 71 analysed, including 26 PPs were detected although many of them with low frequency of occurrence. Only 13 compounds, which belong to four different classes (VOCs, organochlorinated pesticides, phthalates and tributyltin compounds (TBT)) showed a frequency o…

Multivariate SPC of a sequencing batch reactor for wastewater treatment

Data from a sequencing batch reactor (SBR) operated for enhanced biological phosphorus removal from wastewater have been analysed in order to propose an efficient MSPC scheme of the process. Different multivariate bilinear approaches have been applied and compared in terms of their capabilities for on-line and off-line fault detection and diagnosis. The typical three-way data structure from a batch process was unfolded batch-wise and variable-wise. In the latter case, two models were built: with (AT) and without (WKFH) removing the main non-linear behaviour of the process data. Since the process consists of several stages, the monitoring strategies tested include: one model for all stages a…

Biological Nutrient Removal Model No. 2 (BNRM2): a general model for wastewater treatment plants

This paper presents the plant-wide model Biological Nutrient Removal Model No. 2 (BNRM2). Since nitrite was not considered in the BNRM1, and this previous model also failed to accurately simulate the anaerobic digestion because precipitation processes were not considered, an extension of BNRM1 has been developed. This extension comprises all the components and processes required to simulate nitrogen removal via nitrite and the formation of the solids most likely to precipitate in anaerobic digesters. The solids considered in BNRM2 are: struvite, amorphous calcium phosphate, hidroxyapatite, newberite, vivianite, strengite, variscite, and calcium carbonate. With regard to nitrogen removal via…

Kinetic modeling of autotrophic microalgae mainline processes for sewage treatment in phosphorus-replete and -deplete culture conditions

[EN] A kinetic model of autotrophic microalgal growth in sewage was developed to determine the biokinetic processes involved, including carbon-, nitrogen- and phosphorus-limited microalgal growth, dependence on light intensity, temperature and pH, light attenuation and gas exchange to the atmosphere. A new feature was the differentiation between two metabolic pathways of phosphorus consumption according to the availability of extracellular phosphorus. Two scenarios were differentiated: phosphorus-replete and -deplete culture conditions. In the former, the microalgae absorbed phosphorus to grow and store polyphosphate. In the latter the microalgae used the stored polyphosphate as a phosphoru…

A filtration model applied to submerged anaerobic MBRs (SAnMBRs)

The aim of this study was to develop a model able to correctly reproduce the filtration process of submerged anaerobic MBRs (SAnMBRs). The proposed model was calibrated and validated in a SAnMBR demonstration plant fitted with industrial-scale hollow-fibre membranes. Three suspended components were contemplated in the model: total solids concentration; dry mass of cake on the membrane surface; and dry mass of irreversible fouling on the membrane surface. The model addressed the following physical processes: the build-up and compression of the cake layer during filtration; cake layer removal using biogas sparging to scour the membrane; cake layer removal during back-flushing; and the consoli…

Modelling of an activated primary settling tank including the fermentation process and VFA elutriation

A complete model of a primary settler including both sedimentation and biological processes is presented. It is a one-dimensional model based on the solids flux concept and the conservation of mass that uses the Takács model for the settling velocity, which is corrected by a compression function in the lower layers. The biological model is based on the ASM2 and enlarged with the fermentation model proposed by this research group. The settler was split in ten layers and the flux terms in the mass balance for each layer is obtained by means of the settling model. A pilot plant has been operated to study the primary sludge fermentation and volatile fatty acids (VFA) elutriation in a primary se…

Sludge management modeling to enhance P-recovery as struvite in wastewater treatment plants

[EN] Interest in phosphorus (P) recovery and reuse has increased in recent years as supplies of P are declining. After use, most of the P remains in wastewater, making Wastewater Treatment Plants (WWTPs) a vital part of P recycling. In this work, a new sludge management operation was studied by modeling in order to recover Pin the form of struvite and minimize operating problems due to uncontrolled P precipitation in WWTPs. During the study, intensive analytical campaigns were carried out on the water and sludge lines. The results identified the anaerobic digester as a "hot spot" of uncontrolled P precipitation (9.5 gP/kg sludge) and highlighted possible operating problems due to the accumu…

Effect of intracellular P content on phosphate removal in Scenedesmus sp. Experimental study and kinetic expression

The present work determines the effect of phosphorus content on phosphate uptake rate in a mixed culture of Chlorophyceae in which the genus Scenedesmus dominates. Phosphate uptake rate was determined in eighteen laboratory batch experiments, with samples taken from a progressively more P-starved culture in which a minimum P content of 0.11% (w/w) was achieved. The results obtained showed that the higher the internal biomass P content, the lower the phosphate removal rate. The highest specific phosphate removal rate was 6.5 mgPO4 P gTSS -1 h -1 . Microalgae with a P content around 1% (w/w) attained 10% of this highest removal rate, whereas those with a P content of 0.6% (w/w) presented 50% …

Fermentation of municipal primary sludge: effect of SRT and solids concentration on volatile fatty acid production

Laboratory bench-scale experiments were conducted to investigate the performance of primary sludge fermentation for volatile fatty acids production. Primary sludges from two major wastewater treatment plants located in Valencia (Pinedo and Carraixet) were used. Experiments were performed at solids retention times between 4 and 10 days, and total volatile solids concentrations between 0.6% and 2.8%. Operation at two temperatures (20 degrees C and 30 degrees C) was also checked. Results indicated the importance of feed sludge characteristics on volatile fatty acids yields, being approximately double for the Carraixet wastewater treatment plant sludge than for the Pinedo plant. In both cases, …

Estudio del proceso de desnitrificación en un reactor SBR alimentado con el afluente de un reactor anaerobio de membranas sumergidas SAnMER

El tratamiento o postratamiento de efluentes anaerobios sugiere del estudio de diversos procesos que permitan la eliminación o remoción de los contaminantes presentes. El objetivo de este trabajo consistió en el estudio de la capacidad de desnitrificación en condiciones anóxicas utilizando los distintos dadores de electrones, disponibles en el efluente del reactor SAnMBR tales como: ácidos grasos volátiles, metano disuelto y sulfuro. La importancia de este estudio radica en la posibilidad de utilizar los ácidos grasos volátiles, el metano y el sulfuro disuelto como dadores de electrones, para la eliminación de nitrógeno. El metano disuelto es una fuente de carbono muy barato y un gas de efe…

Identificación de bacterias filamentosas Thiothrix en el tratamiento del efluente de un reactor anaerobio de membranas sumergidas (SAnMBR)

En el tratamiento biológico de aguas residuales participan diversos microorganismos entre los que se encuentran las bacterias filamentosas. El crecimiento excesivo e incontrolado de estos microorganismos genera problemas asociados al esponjamiento de los fangos conocido como bulking y la formación de espumas o foaming. La correcta identificación de estos organismos tiene un papel importante en la toma de decisiones para la correcta operación de las plantas de tratamiento de agua residual. Los tratamientos anaerobios empleados para el tratamiento de aguas residuales urbanas e industriales, con un contenido alto de sulfatos en el afluente, generan efluentes que contienen concentraciones impor…

Control of activated sludge settleability using preaeration and preprecipitation

This paper deals with the addition of a preaeration and a preprecipitation stage to a conventional activated sludge process. The experiments were carried out in a pilot plant using wastewater from the city of Valencia (Spain) as feed. The effect of the F/M ratio and sludge age on sludge settleability was established. In both cases, process stability was observed to increase with respect to the conventional process. Good sludge settleability was thus assured in a greater F/M ratio range. A comparative economic study was also carried out.

Use of rumen microorganisms to boost the anaerobic biodegradability of microalgae

[EN] A laboratory bioreactor using rumen microorganisms to treat Scenedesmus spp. biomass was operated for 190 days. At first the bioreactor operated as a Rumen-like Fermenter (RF) with a Sludge Retention Time (SRT) of 7 days. The RF was subsequently transformed into an anaerobic digestion system including two configurations: continuously-stirred tank reactor and anaerobic membrane bioreactor in which different SRT values of up to 100 days were assessed. Methane production peaked at 214 mL CH4 g−1 CODIn with a SRT of 100 days. COD removal and BDP peaked at above 70% and 60%, respectively, at the highest SRT, with no pre-treatment prior to microalgae digestion. The waste sludge product…

Anaerobic treatment of urban wastewater in membrane bioreactors: evaluation of seasonal temperature variations

The objective of this study was to evaluate the effect of seasonal temperature variations on the anaerobic treatment of urban wastewater in membrane bioreactors (MBRs). To this aim, sludge production, energy recovery potential, chemical oxygen demand (COD) removal and membrane permeability were evaluated in a submerged anaerobic MBR fitted with industrial-scale membrane units. The plant was operated for 172 days, between summer and winter seasons. Sludge production increased and energy recovery potential decreased when temperature decreased. COD removal and membrane permeability remained nearby stable throughout the whole experimental period.

Short and long-term experiments on the effect of sulphide on microalgae cultivation in tertiary sewage treatment.

[EN] Microalgae cultivation appears to be a promising technology for treating nutrient-rich effluents from anaerobic membrane bioreactors, as microalgae are able to consume nutrients from sewage without an organic carbon source, although the sulphide formed during the anaerobic treatment does have negative effects on microalgae growth. Short and long-term experiments were carried out on the effects of sulphide on a mixed microalgae culture. The short-term experiments showed that the oxygen production rate (OPR) dropped as sulphide concentration increased: a concentration of 5 mg S L¿1 reduced OPR by 43%, while a concentration of 50 mg S L¿1 came close to completely inhibiting microalgae gro…

Sewage sludge management for phosphorus recovery as struvite in EBPR wastewater treatment plants

The influence of separate and mixed thickening of primary and secondary sludge on struvite recovery was studied. Phosphorus precipitation in the digester was reduced from 13.7 g of phosphorus per kg of treated sludge in the separate thickening experiment to 5.9 in the mixed thickening experiment. This lessening of the uncontrolled precipitation means a reduction of the operational problems and enhances the phosphorus availability for its later crystallization. High phosphorus precipitation and recovery efficiencies were achieved in both crystallization experiments. However, mixed thickening configuration showed a lower percentage of phosphorus precipitated as struvite due to the presence of…

Model-based automatic tuning of a filtration control system for submerged anaerobic membrane bioreactors (AnMBR)

This paper describes a model-based method to optimise filtration in submerged AnMBRs. The method is applied to an advanced knowledge-based control system and considers three statistical methods: (1) sensitivity analysis (Morris screening method) to identify an input subset for the advanced controller; (2) Monte Carlo method (trajectory-based random sampling) to find suitable initial values for the control inputs; and (3) optimisation algorithm (performing as a supervisory controller) to re-calibrate these control inputs in order to minimise plant operating costs. The model-based supervisory controller proposed allowed filtration to be optimised with low computational demands (about 5min). E…

Optimisation of sludge line management to enhance phosphorus recovery in WWTP

The management of the sludge treatment line can be optimized to reduce uncontrolled phosphorus precipitation in the anaerobic digester and to enhance phosphorus recovery in WWTP. In this paper, four operational strategies, which are based on the handling of the prefermented primary sludge and the secondary sludge from an EBPR process, have been tested in a pilot plant. The separated or mixed sludge thickening, the use of a stirred contact tank and the elutriation of the thickened sludge are the main strategies studied. Both the reduction of phosphorus precipitation in the digester and the supernatant suitability for a struvite crystallization process were assessed in each configuration. The…

Environmental impact of submerged anaerobic MBR (SAnMBR) technology used to treat urban wastewater at different temperatures

[EN] The objective of this study was to assess the environmental impact of a submerged anaerobic MBR (SAnMBR) system in the treatment of urban wastewater at different temperatures: ambient temperature (20 and 33 degrees C), and a controlled temperature (33 degrees C). To this end, an overall energy balance (OEB) and life cycle assessment (LCA), both based on real process data, were carried out. Four factors were considered in this study; (1) energy consumption during wastewater treatment; (2) energy recovered from biogas capture; (3) potential recovery of nutrients from the final effluent; and (4) sludge disposal. The OEB and LCA showed SAnMBR to be a promising technology for treating urban…

Precipitation assessment in wastewater treatment plants operated for biological nutrient removal: a case study in Murcia, Spain.

The Murcia Este Wastewater Treatment Plant is the largest wastewater treatment plant in Murcia (Spain). The plant operators have continuously found pipe blockage and accumulation of solids on equipment surfaces during the anaerobic digestion and post-digestion processes. This work studies the precipitation problems in the Murcia Este Wastewater Treatment Plant in order to locate the sources of precipitation and its causes from an exhaustive mass balance analysis. The DAF thickener and anaerobic digester mass balances suggest that most of the polyphosphate is released during excess sludge thickening. Despite the high concentrations achieved in the thickened sludge, precipitation does not occ…

On-line monitoring of photosynthetic activity based on pH data to assess microalgae cultivation

[EN] Microalgae performance of outdoor cultivation systems is influenced by environmental and operating dynamics. Monitoring and control systems are needed to maximise biomass productivity and nutrient recovery. The goal of this work was to corroborate that pH data could be used to monitor microalgae performance by means of data from an outdoor membrane photobioreactor (MPBR) plant. In this system, microalgae photosynthetic activity was favoured over other physical and biological processes, so that the pH data dynamics was theoretically related to the microalgae carbon uptake rate (CUR). Shortand long-term continuous operations were tested to corroborate the relationship between the first d…

Effect of light intensity, light duration and photoperiods in the performance of an outdoor photobioreactor for urban wastewater treatment

[EN] A series of eight experiments were carried out to analyse the effects of light intensity, light duration and photoperiods on a microalgae culture for treating AnMBR effluent at an outdoor photobioreactor (PBR) plant. Improved performance was achieved in terms of nutrient recovery rates, biomass productivity and effluent nutrient concentrations at a higher net photon flux. However, the higher irradiance was also responsible for lower biomass productivity:light irradiance ratios. None of the experiments with different lighting regimes and the same net photon flux showed any significant differences. The data obtained suggest that microalgae performance in this system did not depend on the…

Study of the factors affecting activated sludge settling in domestic wastewater treatment plants

A study has been made of the influence of the process parameters on the settling characteristics of sludge in domestic wastewater treatment plants. The experiments were conducted at a pilot plant situated at the Wastewater Treatment Plant of Valencia, Spain (1,000,000 inhabitants). The influent to the pilot plant was the same as that of the plant. It was found that F/M ratios in the range of 0.25-0.60 g DBO5/g MLVSS day produce values of SVI representative of good settleability of the sludge. Values of sulphide concentration in the influent above 1.0 mg/l negatively affect the process, causing bulking and floating sludge. High values of fats were found to have no influence on the SVI, but d…

Biological nutrient removal model No.1 (BNRM1)

This paper presents the results of the work carried out by the CALAGUA Group on Mathematical Modelling of Biological Treatment Processes: the Biological Nutrient Removal Model No.1. This model is based on a new concept for dynamic simulation of wastewater treatment plants: a unique model can be used to design, simulate and optimize the whole plant, as it includes most of the biological and physico-chemical processes taking place in all treatment operations. The physical processes included are: settling and clarification processes (flocculated settling, hindered settling and thickening), volatile fatty acids elutriation and gasÐliquid transfer. The chemical interactions included comprise aci…

Energy saving in the aeration process by fuzzy logic control

An aeration fuzzy logic based control system has been developed and tested in the main aerobic reactor of a BARDENPHO process pilot plant. This system has been compared with two ordinary aeration process controllers: one- and two-aeration-level on/off controllers. Energy savings of about 40% over the one-level on/off controller and a more stable closed-loop response have been obtained. Thus, an improvement of about 60% in average deviation can be accomplished by the use of an AFLBC.

Identification and quantification of microbial populations in activated sludge and anaerobic digestion processes

Eight different phenotypes were studied in an activated sludge process (AeR) and anaerobic digester AnD) in a full-scale wastewater treatment plant by means of fluorescent in situ hybridization (FISH) and automated FISH quantification software. The phenotypes were ammonia-oxidizing bacteria, nitrite-oxidizing bacteria, denitrifying bacteria, phosphate-accumulating organisms (PAO), glycogen-accumulating organisms (GAO), sulphate-reducing bacteria (SRB), methanotrophic bacteria and methanogenic archaea. Some findings were unexpected: (a) Presence of PAO, GAO and denitrifiers in the AeR possibly due to unexpected environmental conditions caused by oxygen deficiencies or its ability to survive …

Comparison of different predictive models for nutrient estimation in a sequencing batch reactor for wastewater treatment

Abstract In this paper different predictive models for nutrient estimation in a sequencing batch reactor (SBR) for wastewater treatment are compared: principal component regression (PCR), partial least squares (PLS), and artificial neural networks (ANNs). Two unfolding procedures were used: batch-wise and variable-wise. For the latter unfolding method, X and Y matrix augmentation with lagged variables were used in some models to incorporate process dynamics. The results have shown that batch-wise unfolding PLS models outperform the other approaches. The ANN models are good predictive models, but in this particular case-study, they do not outperform those multivariate projection models that …

Struvite precipitation assessment in anaerobic digestion processes

Struvite precipitation causes important operational problems during the sludge treatment process, especially when EBPR sludge is treated. Predicting struvite formation is critical to be able to design process alternative that best minimises struvite precipitation. With this aim, phosphorus precipitation in an anaerobic digestion pilot plant was studied using experimental data and mass balance analysis. The results obtained showed significant phosphorus precipitation as struvite (58% of the fixed phosphorus) and a low precipitation of calcium phosphates (15%), forming mainly hydroxyapatite (HAP). The rest of the phosphorus fixed in the digester (27%) was attributed to adsorption processes on…

Dataset to assess the shadow effect of an outdoor microalgae culture

[EN] This data in brief (DIB) article is related to a Research article [1]. Microalgae biomass absorb the light photons that are supplied to the culture, reducing the light availability in the inner parts of the photobioreactors. This is known as self-shading or shadow effect. This effect has been widely studied in lab conditions, but information about self-shading in outdoor photobioreactors is scarce. How this shadow effect affects the light availability in an outdoor photobioreactor was evaluated. In addition, advantages and disadvantages of different artificial light sources which can overcome light limitation are described.

Instrumentation, control, and automation for submerged anaerobic membrane bioreactors

A submerged anaerobic membrane bioreactor (AnMBR) demonstration plant with two commercial hollow-fibre ultrafiltration systems (PURON® , Koch Membrane Systems, PUR-PSH31) was designed and operated for urban wastewater treatment. An instrumentation, control, and automation (ICA) system was designed and implemented for proper process performance. Several single-input-single-output (SISO) feedback control loops based on conventional on off and PID algorithms were implemented to control the following operating variables: flow-rates (influent, permeate, sludge recycling and wasting, and recycled biogas through both reactor and membrane tanks), sludge wasting volume, temperature, transmembrane pr…

A pilot-scale study of struvite precipitation in a stirred tank reactor: Conditions influencing the process

Currently, the two most developed techniques for recovering phosphorus from wastewater consist of the formation of calcium phosphates and struvite (MgNH(4)PO(4).6H(2)O). In this work the influence of the operational conditions on the struvite precipitation process (pH in the reactor, hydraulic retention time, and magnesium:phosphorus, nitrogen:phosphorus, and calcium:magnesium molar ratios) have been studied. Twenty-three experiments with artificial wastewater were performed in a stirred reactor. In order to obtain the pH value maintenance during the crystallization process, a fuzzy logic control has been developed. High phosphorus removal efficiencies were reliably achieved precipitating t…

Monitoring pH and electric conductivity in an EBPR sequencing batch reactor

This paper presents laboratory-scale experimentation carried out to study enhanced biological phosphorus removal. Two anaerobic aerobic (A/O) sequencing batch reactors (SBR) have been operated during more than one year to investigate the information provided by monitoring pH and electric conductivity under stationary and transient conditions. Continuous measurements of these parameters allow detecting the end of anaerobic phosphorus release, of aerobic phosphorus uptake and of initial denitrification, as well as incomplete acetic acid uptake. These results suggest the possibility of using pH and electric conductivity as control parameters to determine the length of both anaerobic and aerobi…

Nonlinear control of an activated sludge aeration process: use of fuzzy techniques for tuning PID controllers

In this paper, several tuning algorithms, specifically ITAE, IMC and Cohen and Coon, were applied in order to tune an activated sludge aeration PID controller. Performance results of these controllers were compared by simulation with those obtained by using a nonlinear fuzzy PID controller. In order to design this controller, a trial and error procedure was used to determine, as a function of error at current time and at a previous time, sets of parameters (including controller gain, integral time and derivative time) which achieve satisfactory response of a PID controller actuating over the aeration process. Once these sets of data were obtained, neural networks were used to obtain fuzzy m…

Modelling biological and chemically induced precipitation of calcium phosphate in enhanced biological phosphorus removal systems

The biologically induced precipitation processes can be important in wastewater treatment, in particular treating raw wastewater with high calcium concentration combined with Enhanced Biological Phosphorus Removal. Currently, there is little information and experience in modelling jointly biological and chemical processes. This paper presents a calcium phosphate precipitation model and its inclusion in the Activated Sludge Model No 2d (ASM2d). The proposed precipitation model considers that aqueous phase reactions quickly achieve the chemical equilibrium and that aqueous-solid change is kinetically governed. The model was calibrated using data from four experiments in a Sequencing Batch Rea…

Improving membrane photobioreactor performance by reducing light path: operating conditions and key performance indicators

[EN] Microalgae cultivation has been receiving increasing interest in wastewater remediation due to their ability to assimilate nutrients present in wastewater streams. In this respect, cultivating microalgae in membrane photobioreactors (MPBRs) allows decoupling the solid retention time (SRT) from the hydraulic retention time (HRT), which enables to increase the nutrient load to the photobioreactors (PBRs) while avoiding the wash out of the microalgae biomass. The reduction of the PBR light path from 25 to 10 cm increased the nitrogen and phosphorus recovery rates, microalgae biomass productivity and photosynthetic efficiency by 150, 103, 194 and 67%, respectively.The areal biomass product…

A systematic approach for fine-tuning of fuzzy controllers applied to WWTPs

A systematic approach for fine-tuning fuzzy controllers has been developed and evaluated for an aeration control system implemented in a WWTP. The challenge with the application of fuzzy controllers to WWTPs is simply that they contain many parameters, which need to be adjusted for different WWTP applications. To this end, a methodology based on model simulations is used that employs three statistical methods: (i) Monte-Carlo procedure: to find proper initial conditions, (ii) Identifiability analysis: to find an identifiable parameter subset of the fuzzy controller and (iii) minimization algorithm: to fine-tune the identifiable parameter subset of the controller. Indeed, the initial locatio…

P-recovery in a pilot-scale struvite crystallisation reactor for source separated urine systems using seawater and magnesium chloride as magnesium sources

[EN] Practical recovery of a non-renewable nutrient, such as phosphorus (P), is essential to support modern agriculture in the near future. The high P content of urine, makes it an attractive source for practicing the recovery of this crucial nutrient. This paper presents the experimental results at pilot-plant scale of struvite crystallisation from a source-separated urine stream using two different magnesium sources, namely magnesium chloride and seawater. The latter was chosen as sustainable option to perform P-recovery in coastal areas. Real seawater was used to assess in a more realistic way its efficiency to precipitate P as struvite, since its composition (with noticeable concentrati…