Solid-state-biased coherent detection of ultra-broadband terahertz pulses

2017

Significant progress in nonlinear and ultrafast optics has recently opened new and exciting opportunities for terahertz (THz) science and technology, which require the development of reliable THz sources, detectors, and supporting devices. In this work, we demonstrate the first solid-state technique for the coherent detection of ultra-broadband THz pulses (0.1-10 THz), relying on the electric-field-induced second-harmonic generation in a thin layer of ultraviolet fused silica. The proposed CMOS-compatible devices, which can be realized with standard microfabrication techniques, allow us to perform ultra-broadband detection with a high dynamic range by employing probe laser powers and bias v…

Fabrication of graphene ruthenium-complex heterostructures

2015

The aim of this study is to understand the photoresponse of a Ruthenium-complex/graphene heterostructure. Early work demonstrated that light detection by graphene field effect devices was enhanced by dropcasting Ruthenium Complex molecules. Here we proposed to fabricate a new class of devices where the Ruthenium-complex molecules are embedded between two layer of CVD monolayer graphene.

Homodyne Solid-State Biased Coherent Detection of Ultra-Broadband Terahertz Pulses with Static Electric Fields.

2021

We present an innovative implementation of the solid-state-biased coherent detection (SSBCD) technique, which we have recently introduced for the reconstruction of both amplitude and phase of ultra-broadband terahertz pulses. In our previous works, the SSBCD method has been operated via a heterodyne scheme, which involves demanding square-wave voltage amplifiers, phase-locked to the THz pulse train, as well as an electronic circuit for the demodulation of the readout signal. Here, we demonstrate that the SSBCD technique can be operated via a very simple homodyne scheme, exploiting plain static bias voltages. We show that the homodyne SSBCD signal turns into a bipolar transient when the stat…

Completely dielectric E-field sensor based on a Lithium Niobate MZI

2008

We report an IO electric field sensor based on a particular cofiguration of Mach-Zehnder interferometer. The device, fabricated on a Lithium Niobate substrate, is totally dielectric, without any presence of metallic electrodes. The Mach-Zehnder was achieved through soft proton exchange and poling technologies. A modulation depth of 92% and an half wave voltage of 107.8 V were measured using a triangular voltage signal.

Surface poling in lithium niobate waveguide creates efficient wavelength conversion

2004

Used with red or IR emitting laser diodes, nonlinear crystals for frequency doubling can result in a small blue emitting laser that is a viable alternative to gallium nitride-based laser diodes.

PPG embedded system for blood pressure monitoring

2014

In this work, we have designed and implemented a microcontroller-based embedded system for blood pressure monitoring through a PhotoPlethysmoGraphic (PPG) technique. In our system, it is possible to perform PPG measurements via reflectance mode. Hardware novelty of our system consists in the adoption of Silicon PhotoMultiplier detectors. The signal received from the photodetector is used to calculate the instantaneous heart rate and therefore the heart rate variability. The obtained results show that, by using our system, it is possible to easily extract both the PPG and the breath signal. These signals can be used to monitor the patients during the convalescence both in hospital and at hom…

Sorgente laser multilinea NIR-RGB in guide ottiche RPE su Nd:LiNbO3

2004

Invited Article: Ultra-broadband terahertz coherent detection via a silicon nitride-based deep sub-wavelength metallic slit

2018

We present a novel class of CMOS-compatible devices aimed to perform the solid-state-biased coherent detection of ultrashort terahertz pulses, i.e., featuring a gap-free bandwidth at least two decades-wide. Such a structure relies on a 1-µm-wide slit aperture located between two parallel aluminum pads, embedded in a 1-µm-thick layer of silicon nitride, and deposited on a quartz substrate. We show that this device can detect ultra-broadband terahertz pulses by employing unprecedented low optical probe energies of only a few tens of nanojoules. This is due to the more than one order of magnitude higher nonlinear coefficient of silicon nitride with respect to silica, the nonlinear material emp…

Random Quasi-Phae-Matching in Tantalatio di Litio: origine del fenomeno, confronto tra propagazione bulk e guidata.

2011

We observe second harmonic generation via random quasi phase matching in a 1.5μm periodically poled lithium tantalate. The presence of a slab waveguides allows the comparison between bulk and guided wave configurations.

One diode circuital model of light soaking phenomena in Dye-Sensitized Solar Cells

2018

Abstract In this work, we report on the modelling of light soaking effect on Ruthenium-based Dye Sensitized Solar cells (DSSCs). Such a phenomenon can be detected when exposing the cells at increasing hours of illumination and produces a reversible performance increase. Starting from the results obtained through the electro-optical characterization of the cells, we applied a one-diode circuital-model. Our results show a good agreement between the experimental and the simulated data, with a mean square error in the order of 10−12 and a maximum error in current lower than 0.6%. Finally such results allowed us to infer some precise trends followed by the cells main electrical parameters and of…

Silica masks for improved surface poling of lithium niobate

2005

Surface periodic poling of congruent lithium niobate was performed with the aid of photolithographically defined silica masks. The latter helped improving the control of duty cycle in the periodic domain poling, with 50:50 mark-to-space ratios. The role of silica was ascertained by numerically solving the Poisson equation.

NEAR INFRARED PICOSECOND PULSED BACKWARD SECOND-HARMONIC-GENERATION IN PERIODICALLY-POLED LITHIUM NIOBATE

2011

We report on backward second-harmonic-generation in bulk periodically-poled congruent lithium niobate with a 3.2μm period. A picosecond pulsed laser allowed us exciting a resonance at 1722nm. The resonances were also resolved by temperature tuning.

Dual-polarization-pump CW laser operation in Nd3+:LiNbO3 channel waveguides fabricated by reverse proton exchange

2008

Abstract In this work, continuous-wave laser action at 1084.5 nm at room temperature in LiNbO 3 :Nd 3+ channel waveguides, fabricated by reverse proton exchange (RPE), is reported. The sample was pumped at λ  = 808 nm in either σ or π-polarized configurations, TE- and TM-pumping schemes, being the laser emission π-polarized at all power levels. The laser characteristics, as function of the pumping scheme (TE or TM), have been obtained. In both cases, the laser emission was stable, without any reduction in the output power even under continuous pump operation at maximum power at room temperature, indicating high resistance to photorefractive damage.

Hybrid Energy Storage Systems: A Brief Overview

2022

In this paper, a brief overview on the Hybrid Energy Storage Systems (HESSs) is provided. In literature, different architectures are chosen to realize the HESSs, and they are based on the principal aim of the HESSs employment. In this paper, the most used HESS topologies are presented, with particular attention to the active, passive and semiactive topologies, highlighting their characteristics. To have a complete schematic idea of the HESSs application, a focus on the principal sizing methodologies is provided, distinguishing the conventional approaches and the advanced ones, exploiting their main applications. Together with a proper sizing, a correct power-sharing strategy is one of the H…

Rateless codes mitigation technique in a turbulent indoor Free Space Optics link

2014

Free Space Optics (FSO) links are affected by several impairments and, among them, optical turbulence is the most important factor that can degrade the link quality. Due to the presence of this phenomenon, the signal irradiance detected by the receiver fluctuates, thus causing erasure errors and fading events. In this work, we present an indoor Free Space Optics link, in which several turbulence conditions are generated by using two heating elements. We show that the generated turbulence causes erasure errors and packet losses during the data transmission, and we also compare the statistical distribution of the samples with the theoretical models. Moreover, we demonstrate how the applicatio…

Second-harmonic generation in surface periodically poled lithium niobate waveguides:On the role of multiphoton absorption

2008

Second harmonic generation is investigated in lithium niobate channels realized by proton exchange and quasi-phase-matched by surface periodic-poling. The reduction in conversion efficiency at high powers is interpreted in terms of multi-photon absorption via two-color terms, yielding an estimate of the dominating three-photon process.

Photoelectric valuation of highly efficient Dye-Sensitized Solar Cells

2015

Nowadays, a growing demand for free and clean energy requires the study and the development of new low-cost solar photovoltaic (PV) cells. Among them, Dye Sensitized Solar Cells (DSSCs) based on ruthenium complexes as sensitizers are assuming a great importance. The DSSCs under study are composed placing in succession a transparent conductive glass on which is screen-printed a mesoporous TiO2 thin film sensitized by a ruthenium based dye (N719) , an electrolytic solution containing a redox couple (I-/I3-) and another conductive glass covered by a thin transparent catalyst platinum film. In this work, we have measured the main photoelectrochemical parameters of the above mentioned DSSCs at d…

P-on-N and N-on-P silicon photomultipliers: responsivity comparison in the continuous wave regime

2013

We report the electrical and optical comparison, in continuous wave regime, of two novel classes of silicon photomultipliers (SiPMs) fabricated on silicon P-type and N-type substrate respectively. Responsivity measurements have been performed with an incident optical power from tenths of picowatts to hundreds of nanowatts and on a broad spectrum, ranging from ultraviolet to near infrared (340-820 nm). For both classes of investigated SiPMs, responsivity shows flat response versus the optical incident power, when a preset overvoltage and wavelength is applied . More in detail, this linear behavior extends up to about 10 nW for lower overvoltages, while a shrink is observed when the reverse b…

Multi-line NIR-RGB emission in Nd:LiNbO3 RPE optical waveguides

2007

Simultaneous generation of four spectral emission lines has been achieved in Nd-doped lithium niobate reverse proton exchange optical waveguide cavities. Using a pump at 800 nm, the four lines were found and they are due to lasing at 1.3735 combined with parametric conversion at 0.687, 0.574 and 0.4 mum.

Counter-propagating difference frequency mixing in diamond with terahertz waves

2013

We investigate four-wave mixing between terahertz and optical pulses in diamond. We observe the occurrence of sum and difference frequency generation, with the latter being phase-matched for terahertz pulses counter-propagating to the optical field.

Layout influence on microwave performance of graphene field effect transistors

2018

The authors report on an in-depth statistical and parametrical investigation on the microwave performance of graphene FETs on sapphire substrate. The devices differ for the gate-drain/source distance and for the gate length, having kept instead the gate width constant. Microwave S -parameters have been measured for the different devices. Their results demonstrate that the cut-off frequency does not monotonically increase with the scaling of the device geometry and that it exists an optimal region in the gate-drain/source and gate-length space which maximises the microwave performance.

Ultraviolet quasi-phase-matched second harmonic generation in surface periodically poled lithium niobate optical waveguides

2007

The compatibility of low concentration (alpha-phase) proton exchange channel waveguides with electric field surface periodic poling of congruent lithium niobate (SPPLN) crystals has been experimentally demonstrated. With such waveguides, we obtained ultraviolet second harmonic generation (SHG) by first order quasi-phase-matching (QPM), a result made possible by the fabrication, on Z-cut LN crystals, of periodic structures with a pitch down to 750 nm. Nonlinear copropagating QPM-SHG measurements have been carried out on such structures. The pump source was a Ti:sapphire laser with a tunability range of 700-980 nm and a 40 GHz linewidth. We have measured UV continuous wave light at 390 nm by …

A silicon photomultiplier-based analog front-end for DC component rejection and pulse wave recording in photoplethysmographic applications

2022

The growing attention towards healthcare and the constant technological innovations in the field of semiconductor components have allowed a widespread availability of smaller devices, suitable to be worn and able to continuously acquire physiological signals. Wearable devices are, however, more prone to yield signals corrupted by artifacts caused by movement. This issue is particularly relevant in photoplethysmographic (PPG) applications where also, to exploit the whole dynamic range of the acquisition device, the DC component of the signal should be removed and the AC component amplified. In this context, we have designed and realized an analog front-end (AFE) suitable to be integrated wit…

Design of a portable (CW) fNIRS embedded system

2014

Reliability of Short-Term Heart Rate Variability Indexes Assessed through Photoplethysmography

2018

The gold standard method to monitor heart rate variability (HRV) comprises measuring the time series of interbeat interval durations from electrocardiographic (ECG) recordings. However, due to the widespread use, simplicity and usability of photoplethysmographic (PPG) techniques, monitoring pulse rate variability (PRV) from pulse wave recordings has become a viable alternative to standard HRV analysis. The present study investigates the accuracy of PRV, measured as a surrogate of HRV, for the quantification of descriptive indexes computed in the time domain (mean, variance), frequency domain (low-to-high frequency power ratio LF/HF, HF band central frequency) and information domain (entropy…

HYDROGELS WITH ORDER POROSITY AT THE MESO-SCALE FOR SENSING

2014

Radiofrequency performances of different Graphene Field Effect Transistors geometries

2016

In this work, we investigated on microwave parameters geometry dependence in Graphene Field Effect Transistors (GFETs). A DC and RF characterization of the fabricated GFETs has been performed. The parametric analysis was carried out on 24 GFET families fabricated on the same chip and differing only for the channel length (Δ) and the gate length (Lg). In order to obtain a statistical average, each family included ten devices with the same geometry.Our study demonstrates that the output resistance and the cut-off frequency depend on both Δ and Lg. As expected, Rout increases with the graphene channel surface thus confirming the good quality of the fabrication procedures. An optimum region whi…

Random quasi-phase-matched second-harmonic generation in periodically poled lithium tantalate

2010

We observe second harmonic generation via random quasi-phase-matching in a 2.0 micron periodically poled, 1-cm-long, z-cut lithium tantalate. Away from resonance, the harmonic output profiles exhibit a characteristic pattern stemming from a stochastic domain distribution and a quadratic growth with the fundamental excitation, as well as a broadband spectral response. The results are in good agreement with a simple model and numerical simulations in the undepleted regime, assuming an anisotropic spread of the random nonlinear component. (C) 2010 Optical Society of America

Duplicazione di frequenza e tuning non lineare in guide d’onda in niobato di litio con poling periodico superficiale

2007

Time resolved confocal luminescence investigations on reverse proton exchange Nd : LiNbO3 channel waveguides

2009

In this work we report on the time and spatial resolved fluorescence of Neodymium ions in LiNbO(3) channel waveguides fabricated by Reverse Proton Exchange. The analysis of the fluorescence decay curves obtained with a sub-micrometric resolution has evidenced the presence of a relevant fluorescence quenching inside the channel waveguide. From the comparison between diffusion simulations and the spatial dependence of the (4)F(3/2) fluorescence decay rate we have concluded that the observed fluorescence quenching can be unequivocally related to the presence of H+ ions in the LiNbO(3) lattice. Nevertheless, it turns out that Reverse Proton Exchange guarantees a fluorescence quenching level sig…

Fabrication and Characterization of Dye-Sensitized Solar Cells

2014

Among the next-generation solar cells, a predominant role is played by Dye sensitized solar cells (DSSC) based on ruthenium complexes as sensitizers. They take advantage of a photoelectrochemical system to transform solar radiation into electric energy. In fact, DSSCs represent a cost-effective alternative to traditional silicon-based photovoltaic devices and they do not require expensive and sophisticated apparatus for their fabrication. In this work, we have produced and tested ruthenium DSSCs. In particular, we have measured the main parameters of these cells, such as the electrical and power performances and the efficiency levels, at different irradiance levels and at different incident…

Analysis of Lithium Niobate Surface Layer after Electric Field Periodic Poling and Proton Exchange

2004

Optical wireless GEO satellite-to-ground downlinks: rateless codes as solution for scintillation fading

2013

Scintillation fading can corrupt a satellite-to-ground optical wireless links with burst errors. Rateless codes, suitable for erasure channel, are able to eliminate or to reduce these communication errors. We analyzed the performances of three different rateless codes in a simulated Geo satellite-to-ground downlink.

First-Order Quasi-Phase-Matched Blue Light Generation in Surface-Poled Ti:Indiffused waveguide

2004

The application of surface periodic poling method for first order quasi-phase-matched (QPM) second harmonic generation (SHG) in Ti:indiffused lithium niobate channel waveguides, was investigated. On a 2.5 μm wide channel waveguide which was periodically poled with a period of 2.47 μm for TM waveguide mode interaction, efficient SHG was observed. The CCD camera was used for monitoring the near-field waveguide mode profiles of both the fundamental and second harmonic waves. The potential of surface domain inversion for efficient nonlinear waveguide interactions was shown after the production of 6 mW of continous-wave blue radiation.

Multiscale Information Storage of Linear Long-Range Correlated Stochastic Processes

2019

Information storage, reflecting the capability of a dynamical system to keep predictable information during its evolution over time, is a key element of intrinsic distributed computation, useful for the description of the dynamical complexity of several physical and biological processes. Here we introduce a parametric approach which allows one to compute information storage across multiple timescales in stochastic processes displaying both short-term dynamics and long-range correlations (LRC). Our analysis is performed in the popular framework of multiscale entropy, whereby a time series is first "coarse grained" at the chosen timescale through low-pass filtering and downsampling, and then …

Integrated optic surface plasmon resonance measurements in a borosilicate glass substrate

2008

The surface plasmon resonance (SPR) technique is a well-known optical method that can be used to measure the refractive index of organic nano-layers adsorbed on a thin metal film. Although there are many configurations for measuring biomolecular interactions, SPR-based techniques play a central role in many current biosensing experiments, since they are the most suited for sensitive and quantitative kinetic measurements. Here we give some results from the analysis and numerical elaboration of SPR data from integrated optics experiments in a particular borosilicate glass, chosen for its composition offering the rather low refractive index of 1.4701 at 633 nm wavelength. These data regard the…

Backward frequency doubling of near infrared picosecond pulses.

2014

We report on backward second-harmonic generation using ps laser pulses in congruent lithium niobate with 3.2 µm periodic poling. Three resonant peaks were measured between 1530 and 1730 nm, corresponding to 16th, 17th and 18th quasi-phase-matching orders in the backward configuration, with a conversion efficiency of 4.75 x 10(-5%)/W for the 16th order. We could also discriminate the contributions from inverted domains randomized in duty-cycle.

Random quasi-phase-matched second harmonic generation in periodically poled lithium tantalate

2009

We experimentally observed and explained bulk second harmonic generation via random quasi-phase-matching, derived from a periodically poled lithium tantalate sample with a randomly patterned mark-to-space-ratio.

Studio della Nonlinearità Quadratica di Zincoblende per la Generazione di TeraHertz in Guida d'Onda: un Confronto di Cristalli Differenti

2009

DFG TeraHertz generation can approach the quantum efficiency limit with much lower peak powers than bulk experiments. We give details on the model and on the waveguide geometry.

Soft proton exchanged channel waveguides in congruent lithium tantalate for frequency doubling

2010

We report on stable optical waveguides fabricated by soft-proton exchange in periodically-poled congruent lithium tantalate in the a-phase. The channel waveguides are characterized in the telecom wavelength range in terms of both linear properties and frequency doubling. The measurements yield a nonlinear coefficient of about 9.5pm/V, demonstrating that the nonlinear optical properties of lithium tantalate are left nearly unaltered by the process. (C) 2010 Optical Society of America

Space-time features of THz emitted from optical rectification occurring in sub-wavelength scales (IWOTST)

2011

Random quasi-phase matching in congruent lithium tantalate waveguides by proton exchange

2012

A report is presented on broadband second-harmonic generation in the range between 930 and 970 nm using random quasi-phase matching in a planar waveguide fabricated by soft proton exchange in congruent lithium tantalate. Bulk and waveguide measurements are compared, outlining the averaging role of guided-wave modes and their interactions with respect to spectral acceptance and near-field profile.

Continuous-Wave Backward Frequency Doubling in Periodically Poled Lithium Niobate

2010

Surface Plasmon Resonance Optical Biosensors for Mannoproteins Detection

2007

Surface periodic poling in congruent lithium tantalate

2006

Time Of Flight measurements via two LiDAR systems with SiPM and APD

2016

In this paper, we present an experimental comparison of two LiDAR systems, employing the SiPM and the APD as photodetectors, in terms of TOF measurements differing for the distance of the target and at different intensities of ambient light. The use of the APD represents the conventional approach, while the implementation of the SiPM is innovative. The performed measurements achieved very promising results, thus demonstrating the effectiveness of our LiDAR based on SiPM.

Power losses comparison between Silicon Carbide and Silicon devices for an isolated DC-DC converter

2021

In recent years, new efficient power devices have been implemented. Silicon Carbide has replaced silicon as regards the production and the utilization of many devices, such as MOSFETs, diodes, IGBTs and many others. SiC devices are characterized by a low reverse recovery charge, high carrier saturation velocity, by which it is possible to work at high frequency, and high breakdown voltage. Thanks to the great thermal conductivity and the wide bandgap, these devices can operate at high temperature and reach high voltages and currents. What is important to stress is the fact that power losses in SiC devices are lower than the silicon ones. These are the reasons why these devices are utilized …

Fabrication and electro-optical characterization of Ruthenium-based Dye-Sensitized Solar Cells

2015

In this paper, we measure the main photoelectrical parameters of Dye Sensitized Solar Cells (DSSCs) based on ruthenium complexes at different irradiance levels, incident wavelengths, temperatures and hours of light soaking

Design and Fabrication of Terahertz Bragg Gratings on a Two-Wire Waveguide

In this study, we present the design and the fabrication procedure of waveguide-integrated Bragg Gratings operating at THz frequencies.

Switching Frequency Effects on the Efficiency and Harmonic Distortion in a Three-Phase Five-Level CHBMI Prototype with Multicarrier PWM Schemes: Expe…

2022

The current climatic scenario requires the use of innovative solutions to increase the production of electricity from renewable energy sources. Multilevel Power Inverters are a promising solution to improve the penetration of renewable energy sources into the electrical grid. Moreover, the performance of MPIs is a function of the modulation strategy employed and of its features (modulation index and switching frequency). This paper presents an extended and experimental analysis of three-phase five-level Cascaded H-Bridges Multilevel Inverter performance in terms of efficiency and harmonic content considering several MC PWM modulation strategies. In detail, the CHBMI performance is analyzed …

Multivariate correlation measures reveal structure and strength of brain–body physiological networks at rest and during mental stress

2021

In this work, we extend to the multivariate case the classical correlation analysis used in the field of network physiology to probe dynamic interactions between organ systems in the human body. To this end, we define different correlation-based measures of the multivariate interaction (MI) within and between the brain and body subnetworks of the human physiological network, represented, respectively, by the time series of delta, theta, alpha, and beta electroencephalographic (EEG) wave amplitudes, and of heart rate, respiration amplitude, and pulse arrival time (PAT) variability. MI is computed: (i) considering all variables in the two subnetworks to evaluate overall brain–body interaction…

Experimental investigation on a cascode-based three-phase inverter for AC drives

2021

High speed electrical drives and machines represent a promising solution to cope with the increasing electrification in several fields, e.g. industrial electronics and mobility. According to that, power electronics is going more and more towards innovative technologies of semiconductor devices, such as Gallium-Nitride (GaN) and Silicon-Carbide (SiC), providing the opportunity of faster switching transients and therefore of higher switching frequencies. A challenging perspective is represented by gaining higher and higher switching frequencies while keeping high voltage and low power losses. In this scenario, the Cascode (CC) configuration can represent a reliable solution in order to reach …

Remote optical monitoring in remotely power assisted passive optical networks

2010

In this paper, the authors present the latest results on a simple and low cost method to achieve a dynamic and flexible network monitoring. By placing several fiber Bragg gratings (FBG) along the passive optical gigabit Ethernet infrastructure (GePON), the proposed modified optical time domain reflectometer (OTDR) is able to monitor the entire system by simply tuning its working wavelength. Furthermore, the optical network terminals (ONT), at the end users premises, have been interconnected to the trunk via an innovative cable able to both carry the optical signal as well as the power supply.

Modelling of Laser Operation in RPE Nd3+:LiNbO3 Channel Waveguides

2006

In this work, laser action in RPE Nd3+:LiNbO3 is modelled by using the overlapping integrals method. Different pumping schemes, TE or TM, have been considered in order to reproduce the experimental measurements. Calculated results indicate that the slope efficiency remains basically independent on the pumping scheme while the threshold pump power increases for TE pumping.

Studio della nonlinearità quadratica di zincoblende per la generazione di TeraHertz in guida d'onda: un confronto di cristalli differenti

2009

DFG TeraHertz generation can approach the quantum efficiency limit with much lower peak powers than bulk experiments. We give details on the model and on the waveguide geometry.

CulnSe2/Zn(S,O,OH) junction on Mo foil by electrochemical and chemical route for photovoltaic applications

2014

Electrodeposition is a convenient technique for the development of low cost materials for photovoltaic (PV) device processing. Using a single step electrodeposition route, several groups have fabricated CIS (CuInSe) and CIGS (CuInGaSe) films [1]. One of the most important requirements for successful application of one-step electrodeposition film formation, is the ability to control composition of the deposited films and to develop polycrystalline microstructures with a low surface roughness and high sintered density. In this preliminary work, CIS films were produced by single bath electrodeposition finding the optimal conditions in order to achieve a dense film with high crystallinity and u…

Responsivity measurements of SiC photodiodes

2014

We investigated the technical features of three novel classes of 4H-SiC vertical Schottky UV photodiodes (henceforth, named SiC8, SiC10, SiC20) employing Ni2Si interdigitated strips whose pitch size is 8, 10 and 20 µm respectively [1] and based on the pinch-off surface effect.

Integrated optic Surface Plasmon Resonance Measurements in Glass substrates

2007

The surface plasmon resonance (SPR) technique is an optical method that can be used to measure the refractive index of organic nano-layers adsorbed on a thin metal film. Although there are many techniques for measuring biomolecular interactions, SPR-based techniques play a central role in many current biosensing experiments, since they are most suited to sensitive and quantitative kinetic measurements. Here we give some results from the analysis and numerical elaboration of SPR data regarding the flow of different solutions with refractive indexes in the range of interest (1-1.4). After a brief discussion of the principles of SPR and of waveguide fabrication technique, we give a description…

Characterization of Ruthenium-based Dye-Sensitized solar cells

2015

In this paper, we measure the main photoelectrical parameters of Dye Sensitized Solar Cells (DSSCs) based on ruthenium complexes at different irradiance levels, incident wavelengths, temperatures and hours of light soaking.

GENERAZIONE DI SECONDA ARMONICA MEDIANTE RANDOM QUASI-PHASE-MATCHING IN TANTALATO DI LITIO POLATO PERIODICAMENTE

2009

We experimentally observed and explained bulk Second Harmonic Generation via Random Quasi-Phase-Matching, derived from a periodically poled Lithium Tantalate sample with a randomly patterned mark-to-space-ratio.

Non-uniform doping concentration CIGS absorber profile for highefficiency solar cells

2016

The quaternary chalcopyrite semiconductor alloy Cu(In,Ga)Se2 (CIGS) is nowadays commonly considered one of the most suitable materials to fabricate cost-effective and high-efficiency photovoltaic cells. Thanks to the optical and structural properties of the absorber layer and to the tunable bandgap, thin-film CIGS cells have reached efficiencies around 20%, not far from the maximum values of traditional crystalline silicon cells. This high efficiency, together with the conceivable low fabrication costs, makes CIGS cells a promising alternative to silicon technology for large-scale production. In order to further improve the cells performance, in a previous work we have already proposed a si…

Disclosing of optical properties of metal/dielectric heterostructures by Spectroscopic Ellipsometry enhanced by Surface Plasmon Resonance

2013

UV Generation in lithium niobate proton exchanged optical waveguides

2006

Stable proton exchanged waveguides in Lithium Tantalate

2008

alpha, beta(1), and kappa(2) phases are investigated for planar waveguide fabrication by proton exchange in congruent lithium tantalate. The effective indices of planar waveguide eigenmodes were monitored over time, revealing that the exchange process induces aging instabilities in all phases except alpha.

Duplicazione di frequenza in guide d'onda in Niobato di Litio con poling periodico: ruolo dell'assorbimento multifotoni

2008

Sensore di campo elettrico completamente dielettrico in ottica integrata.

2008

We report an electric field sensor based on a particular cofiguration of Mach-Zehnder interferometer (MZI). The device, fabricated on a Lithium Niobate substrate, is totally dielectric, without any presence of metallic electrodes. A modulation depth of 92% and an half wave voltage of 107.8 V were measured using a triangular voltage signal.

A portable multisensor system to assess cardiorespiratory interactions through photoplethysmography

2022

Nowadays, the ever-growing interest to health and quality of life of individuals and the advancements in electronic devices technology are pushing the development of portable and wearable biomedical devices able to pursue a minimally invasive monitoring of physiological parameters in daily-life conditions. Such devices can now carry out a real-time assessment of the subjects’ overall health status and possibly even detect ongoing diseases. In this context, we have designed and implemented a multisensor portable system able to perform synchronous real-time acquisitions of electrocardiographic (ECG), photoplethysmographic (PPG) and airflow breathing signals. We investigated cardiorespiratory …

Experimental Investigation on the Performances of Innovative PV Vertical Structures

2019

The sustainable development of our planet is considerably related to a relevant reduction of CO2 global emissions, with building consumption contributing more than 40%. In this scenario, new technological conceptions, such as building-integrated photovoltaic technology, emerged in order to satisfy the requirements of sustainability imposed by the European Union. Therefore, the aim of this work is to provide a technical and economical comparison of the performances of different vertical-mounted innovative photovoltaic systems, potentially integrated on a building instead of on traditional windows or glass walls. The proposed investigation was carried out by means of experimental tests on thr…

Monitoraggio dinamico in reti ottiche di nuova generazione

2009

Polarization effects on the laser operation in RPE Nd3+:LiNbO3 channel waveguides

2005

Analytical Model for wideband THz sources and detectors based on Optical Rectification and Electro-Optic Sampling

2013

An analytical model describing a laser based set-up for wideband THz generation and detection is presented. Particular attention is focused on the main broadband phenomena, which occur when THz radiations have to be handled.

University of Palermo: Exploiting the Optical Quadratic Nonlinearity of Zinc-Blende Semiconductors for Guided-Wave Terahertz Generation: A Material C…

2012

Content synopsis of the following paper: Matteo Cherchi, Alberto Taormina, Alessandro C. Busacca, Roberto L. Oliveri, Saverio Bivona, Alfonso C. Cino, Salvatore Stivala, Stefano Riva Sanseverino, and Claudio Leone, "Exploiting the Optical Quadratic Nonlinearity of Zinc-Blende Semiconductors for Guided-Wave Terahertz Generation: A Material Comparison", IEEE Journal of Quantum Electronics, Vol. 46, N. 3, March 2010

Surface Plasmon Resonance Measurement of Neutravidin Layer on Gold Thin Film

2006

Parametric self-trapping in the presence of randomized quasi phase matching

2010

We report on experimental evidence of parametric spatial solitons in a quadratic crystal with randomized periodic ferroelectric poling. Two-color self-focusing via quadratic cascading overcomes the diffractive nature of both fundamental and frequency-doubled beams.

Signal to noise ratio measurements of silicon photomultipliers in the continuous wave regime

2014

We report on our signal to noise ratio (SNR) measurements carried out, in the continuous wave regime, on a novel class of silicon photomultipliers (SiPMs) fabricated in planar technology on silicon p-type substrate.

Nanopatterned ferroelectric crystals for parametric generation

2006

We report on recent results by surface periodic poling on lithium niobate and lithium tantalate. Such approach allows periodic inversion of the second order susceptibility with nanoscale features using insulating masks. We achieved a world-best 200 nm feature size, as well as good compatibility with alpha-phase proton exchanged channel waveguides in lithium niobate. Preliminary results of surface periodic poling in lithium tantalate also show similar characteristics. Surface poling is best suited for integrated optics devices in technologically-demanding configurations such as backward second harmonic generation and counter propagating optical parametric amplification

Nano-domains definition in congruent lithium niobate by surface periodic electric-field poling

2005

Sub-Wavelength Scale THz Source via Optical Rectification and its Spatio-Temporal Properties

2011

Generazione di seconda armonica nel vicino infrarosso per quasi-accordo di fase in guide a scambio protonico in niobato di litio con polarizzazione p…

2006

Ethanol vapor optical sensors based on polystyrene opals infiltrated with hydrogel

2013

Graded Carrier Concentration Absorber Profile for High Efficiency CIGS Solar Cells

2015

We demonstrate an innovative CIGS-based solar cells model with a graded doping concentration absorber profile, capable of achieving high efficiency values. In detail, we start with an in-depth discussion concerning the parametrical study of conventional CIGS solar cells structures. We have used the wxAMPS software in order to numerically simulate cell electrical behaviour. By means of simulations, we have studied the variation of relevant physical and chemical parameters-characteristic of such devices-with changing energy gap and doping density of the absorber layer. Our results show that, in uniform CIGS cell, the efficiency, the open circuit voltage, and short circuit current heavily depe…

Multiscale Information Decomposition Dissects Control Mechanisms of Heart Rate Variability at Rest and During Physiological Stress.

2019

Heart rate variability (HRV

Electrochemical and chemical synthesis of CIS/Zn(S,O,OH) for thin film solar cells

2014

In this work, we are reporting results on the electrodeposition of the CuInSe2 thin films on molybdenum thin foil substrates. We have used an aqueous non-buffered electrolyte and a careful choice of deposition parameters to ensure a good quality and composition of the deposited films. In addition, CdS was replaced in the buffer layer with a wider bandgap Zn(S,O,OH) film obtained by chemical bath deposition. The deposited films were annealed in inert atmosphere at different temperatures. The influence of annealing temperature on the properties of the films is briefly discussed. Films were also characterized by photoelectrochemical and I-V measurements. Structural characterization was carried…

PPG/ECG Multisite Combo System Based on SiPM Technology

2019

Two versions of a PPG/ECG combined system have been realized and tested. In a first version a multisite system has been equipped by integrating 3 PPG optodes and 3 ECG leads, whereas in another setup a portable version has been carried out. Both versions have been realized by equipping the optical probes with SiPM detectors. SiPM technology is expected to bring relevant advantages in PPG systems and overcome the limitations of physiological information extracted by state of the art PPG, such as poor sensitivity of detectors used for backscattered light detection and motion artifacts seriously affecting the measurements repeatability and pulse waveform stability. This contribution presents t…

Exact Reconstruction of Sub-wavelength THz Source Profile via Combination of Knife-edge Technique and Time-domain Spectroscopy

2013

Generazione di Seconda Armonica per Quasi-Phase-Matching Random in Tantalato di Litio con Poling Periodico

2009

We experimentally observed and explained bulk Second Harmonic Generation via Random Quasi-Phase-Matching, derived from a periodically poled Lithium Tantalate sample with a randomly patterned mark-to-space-ratio.

Feasibility of Linear Parametric Estimation of Dynamic Information Measures to assess Physiological Stress from Short-Term Cardiovascular Variability

2021

Extensive efforts have been recently devoted to implement fast and reliable algorithms capable of assessing the physiological response of the organism to physiological stress. In this study, we propose the comparison between model-free and linear parametric methods as regards their ability to detect alterations in the dynamics and in the complexity of cardiovascular and respiratory variability evoked by postural and mental stress. Dynamic entropy (DE) and information storage (IS) measures were calculated on three physiological time-series, i.e. heart period, respiratory volume and systolic arterial pressure, on 61 healthy subjects monitored in resting conditions as well as during head-up ti…

Advanced piezoresistive sensor achieved by amphiphilic nanointerfaces of graphene oxide and biodegradable polymer blends

2018

This work focuses on the preparation of a piezoresistive sensor device, by exploiting an amphiphilic sample of graphene oxide (GO) as a compatibilizer for poly (lactic acid) (PLA)-Poly (ethylene-glycol) (PEG) blends. The presence of GO determined a high stiffening and strengthening effect, without affecting toughness, and allowed a good stability of mechanical properties up to 40 days. Moreover, GO endowed the materials with electrical properties highly sensitive to pressure and strain variations: the biodegradable pressure sensor showed a responsivity of 35 μA/MPa from 0.6 to 8.5 MPa, a responsivity around 19 μA/MPa from 8.5 to 25 MPa. For lower pressure values (around 0.16–0.45 MPa), inst…

GENERAZIONE DI SECONDA ARMONICA IN GUIDA D’ONDA IN TANTALATO DI LITIO CONGRUENTE CON POLING PERIODICO E CONVERSIONE DI LUNGHEZZA D’ONDA IN BANDA C + L

2010

Here we show the results obtained by the characterization of a lithium-tantalate based device for second-harmonic-generation and all-optical wavelength conversion. The waveguides have been obtained by proton-exchange in a periodically-poled congruent lithium tantalate substrate.

N-on-P and P-on-N Silicon Photomultipliers: Responsivity comparison in the continuous wave regime

2013

We report on the electrical and optical comparison, in continuous wave regime, of two novel classes of silicon photomultipliers fabricated in planar technology on silicon P-type and Ntype substrate respectively. A physical explanation of the experimental results is provided.

Signal to noise ratio measurements of silicon photomultipliers

2014

We report on our signal to noise ratio (SNR) measurements carried out, in the continuous wave regime, on a novel class of silicon photomultipliers (SiPMs) fabricated in planar technology on silicon p-type substrate. SiPMs are large area detectors consisting of a parallel array of Geiger Mode APDs with individual integrated quenching resistors. Each photodiode is an independent photon counting microcell and is connected to a common analog output to produce a summation signal proportional to the number of detected photons [1], [2]. SNR of SiPMs is expressed by the ratio of the SiPM average signal current and the RMS deviation of the overall current (i.e., the overall shot noise current). The …

Responsivity measurements of SiC Schottky photodiodes

2014

We investigated the technical features of three novel classes of 4H-SiC vertical Schottky UV detectors employing Ni2Si interdigitated strips whose pitch size is 8, 10 and 20 µm, respectively, based on the pinch-off surface effect.

Signal to Noise Ratio of Silicon Photomultipliers measured in the Continuous Wave Regime

2014

We performed a Signal to Noise Ratio characterization, in the continuous wave regime, at different bias voltages, frequencies and temperatures, on a novel class of silicon photomultipliers fabricated in planar technology on silicon p-type substrate. Signal to Noise Ratio has been measured as the ratio of the photogenerated current, filtered and averaged by a lock-in amplifier, and the Root Mean Square deviation of the overall current flowing to the device. The measured noise takes into account the shot noise, resulting from the photocurrent and the dark current. We have also performed a comparison between our SiPMs and a photomultiplier tube in terms of Signal to Noise Ratio, as a function …

Statistical analysis of RaptorQ failure probability applied to a data recovery software

2014

In this work, we have implemented a data recovery software integrating the most recent rateless codes, i.e., RaptorQ codes. Thanks to the above-mentioned software, it is possible to recover data loss occurring on several kinds of network conditions. We have performed a statistical analysis of failure probabilities at several configurations of RaptorQ parameters. We have found a good agreement with the theoretical values of a random linear fountain code over Galois Field GF(256). Moreover, we have shown that the probability of having a certain number of failed decoded source blocks - when sending a fixed size file - follows a Poisson distribution.

UV Generation in Surface Periodically Poled Lithium nimbate Proton Exchanged Optical Waveguides

2006

Packet loss recovery in an indoor Free Space Optics link using rateless codes

2014

Free Space Optics (FSO) systems present some important advantages if compared to Radio Frequency links, but they can be affected by several impairments that degrade the link quality and availability. In particular, due to temporary interruptions of the line-of-sight condition between the transmitter and the receiver, packet loss can occur during data transmission. In this work, we present an indoor Free Space Optics link, in which we have systematically generated interruptions of the beam. We demonstrate how the application of the most recent rateless codes, i.e., RaptorQ codes, can strongly improve the link quality by reducing packet loss. In particular, results show that the Packet Error …

Nonlinear Robust Control of a Quadratic Boost Converter in a Wide Operation Range, Based on Extended Linearization Method

2022

This paper proposes a control system for a quadratic boost DC/DC converter in a wide range of operations, based on an inner loop with a sliding mode controller, for reaching a desired equilibrium state, and an outer loop with integral-type controller, for assuring robustness against load and input voltage variations and converter parameter uncertainties. The sliding mode controller is designed with the extended linearization method and assures local asymptotic stability, whereas the integral controller is designed using classical frequency methods, and assures input–output stability. It is shown that the proposed controller also deals with the sudden changes in the nominal operating conditi…

Wideband THz time domain spectroscopy based on optical rectification and electro-optic sampling

2013

We present an analytical model describing the full electromagnetic propagation in a THz time-domain spectroscopy (THz-TDS) system, from the THz pulses via Optical Rectification to the detection via Electro Optic-Sampling. While several investigations deal singularly with the many elements that constitute a THz-TDS, in our work we pay particular attention to the modelling of the time-frequency behaviour of all the stages which compose the experimental set-up. Therefore, our model considers the following main aspects: (i) pump beam focusing into the generation crystal; (ii) phase-matching inside both the generation and detection crystals; (iii) chromatic dispersion and absorption inside the c…

Responsivity measurements of silicon carbide Schottky photodiodes in the UV range

2014

We report on the design and the electro-optical characterization of new classes of 4H-SiC Schottky UV detectors, fabricated employing Ni 2 Si interdigitated strips. We have measured, in dark conditions, the forward and reverse I-V characteristics as a function of temperature and C-V characteristics. Responsivity measurements of the devices, as function of wavelength in the UV range, of package temperature and of applied reverse bias are reported. We also compared devices featuring different strip pitch sizes, discussing their performances, and found the device exhibiting best results.

Design and development of a continuous wave functional near infrared spectroscopy system

2014

Functional Near InfraRed Spectroscopy uses light sources and optical detectors for human brain monitoring. In this paper, a portable, low cost, battery-operated, multi-channel, continuous wave fNIRS embedded system, hosting up to 64 LED sources and 128 Silicon PhotoMultiplier optical detectors, is reported on. The designed system is based on a scalable architecture, in which each probe consists of 8 modular and flexible stands, able to host 4 bi-color LEDs as light sources, 16 silicon photomultipliers as photodetectors and a temperature sensor. The hardware structure allows to easily set up several relevant parameters: the timing of the LEDs, the optical power emitted by the LEDs; the acqui…

Optical turbulence measurements and channel modeling of an indoor Free Space Optics link (Abstract)

2014

Nonlinear brain-heart interactions in children with focal epilepsy assessed by mutual information of EEG and heart rate variability

2019

Network physiology is a recent approach describing the human body as an integrated network composed of several organ systems which continuously interact to produce healthy and diseased states. In this work, we apply the network physiology paradigm to study dynamical interactions between EEG activity and heart rate variability in children suffering from focal epilepsy. We aim to study the characteristics of brainheart coupling between, before, and after seizures to better understand the physiological mechanisms underlying seizure onset in the pre-ictal phase and the recovery of normal autonomic function in the post-ictal phase. In perspective, linking the dynamic information of brain-heart c…

CIGS PV Module Characteristic Curves Under Chemical Composition and Thickness Variations

2014

This paper analyzes how the electrical characteristics of a CIGS photovoltaic module are affected by the chemical composition and by the thickness variations of the CIGS absorber. The electrical characteristics here considered are the short circuit current, the open circuit voltage, the efficiency and the power peak. The chemical composition is varied by tuning the ratio between gallium and indium. This analysis has been performed by means of the wxAMPS software, developed by the University of Illinois. The above variations have been taken into account on a PV module made of 72 cells. This analysis has been carried out employing a PV module mathematical model developed and implemented by th…

Design and realization of a portable multichannel continuous wave fNIRS

2014

A design and implementation of a portable functional Near InfraRed Spectroscopy embedded system prototype is described. In this theoretical and experimental work, we present an embedded system hosting 64 LED sources and 128 Silicon PhotoMultiplier detectors (SiPM). The elementary part of the structure is a flexible probe “leaf” consisting of 16 SiPMs, 4 couples of LEDs, each operating at two wavelengths, and a temperature sensor. The hardware system is based on an ARM main microcontroller that allows to perform both the switching time of LEDs and the acquisition of the SiPM outputs. The performed preliminary experimental tests achieved very promising results, thus demonstrating the effectiv…

Nonlinear Disorder Mapping Through Three-Wave Mixing

2010

We implement a simple and powerful approach to characterize the domain distribution in the bulk of quadratic ferroelectric crystals via far-field second-harmonic spectroscopy. The approach is demonstrated in a lithium tantalate sample with periodic electric field poling and random mark-to-space ratio.

Design and development of a fNIRS system prototype based on SiPM detectors

2014

Functional Near Infrared Spectroscopy (fNIRS) uses near infrared sources and detectors to measure changes in absorption due to neurovascular dynamics in response to brain activation. The use of Silicon Photomultipliers (SiPMs) in a fNIRS system has been estimated potentially able to increase the spatial resolution. Dedicated SiPM sensors have been designed and fabricated by using an optimized process. Electrical and optical characterizations are presented. The design and implementation of a portable fNIRS embedded system, hosting up to 64 IR-LED sources and 128 SiPM sensors, has been carried out. The system has been based on a scalable architecture whose elementary leaf is a flexible board …

Design and implementation of a portable fNIRS embedded system

2015

We report on the design, development and operation of a portable, low cost, battery-operated, multi-channel, functional Near Infrared Spectroscopy embedded system, hosting up to 64 optical sources and 128 Silicon PhotoMultiplier optical detectors. The system is realized as a scalable architecture, whose elementary leaf consists of a probe board provided with 16 SiPMs, 4 couples of bi-color LED, and a temperature sensor, built on a flexible stand. The hardware structure is very versatile because it is possible to handle both the switching time of the LED and the acquisition of the photodetectors, via an ARM based microcontroller.

UV quasi-phase-matched second harmonic in LiTaO3 channel waveguide

2008

Progettazione e realizzazione di un sistema Continuous Wave fNIRS basato su tecnologia SiPM

2014

Guide a scambio protonico in Tantalato di Litio stabili nel tempo

2008

Synergistic and Redundant Brain-Heart Information in Patients with Focal Epilepsy

2020

In this work, partial information decomposition (PID) was applied to the time series of heart rate and EEG amplitude variability to investigate the dynamical interactions in brain-heart coupling before and after epileptic seizures. From ECG and EEG signals collected on 23 children suffering from focal epilepsy, the RR intervals and the EEG variance at ipsilateral and contralateral temporal electrodes were computed in four different time windows before and after the seizures. Static PID was used to obtain redundant, unique and synergistic components of the total information shared between the series of RR and EEG variance. Results highlight, in the progression from preictal to postictal stat…

Design of a Multichannel Continuous Wave fNIRS System implemented with SiPM

2013

Performance Investigation of Fountaine Codes on a Simulated Terrestrial Free Space Optical Channel

2012

Mixed-Mode Operation of Hybrid Phase-Change Nanophotonic Circuits

2016

Phase change materials (PCMs) are highly attractive for nonvolatile electrical and all-optical memory applications because of unique features such as ultrafast and reversible phase transitions, long-term endurance, and high scalability to nanoscale dimensions. Understanding their transient characteristics upon phase transition in both the electrical and the optical domains is essential for using PCMs in future multifunctional optoelectronic circuits. Here, we use a PCM nanowire embedded into a nanophotonic circuit to study switching dynamics in mixed-mode operation. Evanescent coupling between light traveling along waveguides and a phase-change nanowire enables reversible phase transition b…

Analysis of Lithium Niobate Surface after Electric Field Periodic Poling and Proton Exchange

2004

Phosphate ions detection by using an electrochemical sensor based on laser-scribed graphene oxide on paper

2023

In this work, electrodes based on laser-scribed reduced graphene oxide were fabricated using filter paper as the substrate. To fabricate the electrodes, a water suspension of graphene oxide was filtered to produce a continuous and uniform film of graphene oxide on the filter paper surface. Subsequently, a CO2 laser was used to "write" the working, counter and reference eelctroes by reducing graphene oxide in specific areas to define complete sensors. Referecnce electrodes were then coated with a commercial Ag/AgCl conductive paste to produce a quasi Ag/AgCl reference. As fabricated devices were employed as electrochemical sensors for detection of phosphate ions in water by employing the mol…

Monitoring System of Passive Optical Networks with Remotely Power Supply of Optical Network Terminals

2011

In this paper, the authors, present last results on a low cost method to monitoring Passive-Optical-Network, which it uses Fiber-Bragg-Gratings and a modified Optical-Time-Domain-Reflectometer, and a remote power supply of Optical-Network-Terminals by a bivalent-use cable.

Correlated channel model for terrestrial Free Space Optics: performance analysis of rateless codes

2012

We describe a novel correlated channel model able to predict random temporal fluctuations of optical signal irradiance caused by scintillation. With regards to the same channel, we also report simulation results on the error mitigation performance of Luby-Transform and Raptor codes.

Fabrication and analysis of the layout impact in Graphene Field Effect Transistors (GFETs)

2016

In this work we focused on the analysis of Graphene Field Effect Transistor (GFET) microwave parameters dependence on geometries. In particular, a statistical, experimental investigation of the cut-off frequency (ft) dependency on both the gate-drain/source distance (Δ) and the gate length (Lg) was carried out. 24 GFET families on the same chip were fabricated, each one made of 10 identical (same geometry) devices. The analysis of the measured data shows that ft is both Δ and Lg dependent, and that there exists an optimal region in Δ and Lg design space.

Low-invasive multisensor real-time acquisition system for the assessment of cardiorespiratory and skin conductance parameters

2022

In recent years, the attention to the health and comfort of the individual, together with the electronic miniaturization progress, have led to an increased interest in the development of biomedical devices that are able to acquire a multitude of biomedical signals. Such devices should be wearable and comfortable during daily use, to be thus suitable for continuously monitoring psychophysical health states. In this context, we have designed and realized a portable biomedical device capable of real-time acquisition of electrocardiographic (ECG), photoplethysmographic (PPG), breathing and galvanic skin response (GSR) signals, for a noninvasive monitoring of multiple physiological parameters. T…

The role of nonlinear optical absorption in narrowband difference-frequency terahertz-wave generation

2010

We present a general analysis of the influence of nonlinear optical absorption on terahertz generation via optical difference frequency generation, when reaching for the quantum conversion efficiency limit. By casting the equations governing the process in a suitably normalized form, including either two-photon- or three-photon-absorption terms, we have been able to plot universal charts for phase matched optical-to-terahertz conversion for different values of the nonlinear absorption coefficients. We apply our analysis to some experiments reported to date, in order to understand to what extent multiphoton absorption could have played a role and also to predict the maximum achievable conver…

Confocal optical techniques to study channel waveguides in LiNbO3

2008

Electrical characterization of deoxyribonucleic acid hybridization in metal-oxide-semiconductor-like structures

2012

In this work, metal-oxide-semiconductor (MOS)-like sensors in which deoxyribonucleic acid (DNA) strands are covalently immobilized either on Si oxide or on a gold surface were electrically characterized. Si oxide fabrication process allowed us to have a surface insensitive to the solution pH. A significant shift in the flat band voltage was measured after single strand DNA immobilization (+0.47 +/- 0.04 V) and after the complementary strand binding (+0.07 +/- 0.02 V). The results show that DNA sensing can be performed using a MOS structure which can be easily integrated in a more complex design, thus avoiding the problems related to the integration of micro-electrochemical cells.

Surface Periodic Poling in Lithium Niobate and Lithium Tantalate

2005

Periodic Poling of Lithium Niobate crystals (PPLN) by means of electric field has revealed the best technique for finely tailoring PPLN structures and parameters, which play a central role in many current researches in the field of nonlinear integrated optics. Besides the most studied technique of bulk poling, recently a novel technique where domain inversion occurs just in a surface layer using photoresist or silica masks has been devised and studied. This surface periodic poling (SPP) approach is best suited when light is confined in a thin surface guiding layer or stripe, as in the case of optical waveguide devices. Also, we found that SPP respect to bulk poling offers two orders of magn…

Backward second-harmonic generation of near infrared picosecond pulses

2014

We report on backward second-harmonic generation using picosecond laser pulses in congruent lithium niobate with 3.2 µm periodic poling. By tuning both the pump wavelength and the sample temperature, we observed three resonant peaks in the range 1530-1730 nm, corresponding to 16th, 17th and 18th quasi-phase-matching orders, respectively. A maximum conversion efficiency of 0.475% was achieved at the 16th order with a 10 kW peak pump power. The latter is the highest conversion reported in bulk to date, for the backward configuration, with an improvement greater than 50% with respect to those previously achieved with nanosecond pulses for the same order of resonance.

Low invasive multisensor acquisition system for real-time monitoring of cardiovascular and respiratory parameters

2020

The recent advances in multiparametric monitoring of biosignals and management of big data prompt for the development of devices and techniques for the extraction of indicators with physiological relevance. In this context, we have designed and realized a portable electronic system, equipped with simple biomedical sensors, able to synchronously record multiple electrocardiographic (ECG), photoplethysmographic (PPG) and breathing signals, for carrying out a non-invasive monitoring of several cardiovascular parameters. In this work, we show the results of preliminary measurements performed following a specific physiological protocol (i.e., deep breathing with 10 s per cycle). The system allow…

Dependence of Terahertz Emission and Detection in Photoconductive Antennas on Laser Parameters

In this study, we employ a standard Terahertz time-domain spectroscopy (THz-TDS) setup based on two photoconductive antennas (PCAs) for THz radiation generation and detection. The characterization of the emission and detection performance as a function of the input pulse wavelength and bandwidth is performed.

Responsivity measurements of 4H-SiC Schottky photodiodes for UV light monitoring

2014

We report on the design and the electro-optical characterization of a novel class of 4H-SiC vertical Schottky UV detectors, based on the pinch-off surface effect and obtained employing Ni2Si interdigitated strips. We have measured, in dark conditions, the forward and reverse I–V characteristics as a function of the temperature and the C–V characteristics. Responsivity measurements of the devices, as a function of the wavelength (in the 200 – 400 nm range), of the package temperature and of the applied reverse bias are reported. We compared devices featured by different strip pitch size, and found that the 10 μm device pitch exhibits the best results, being the best compromise in terms of fu…

Comparison on the use of PV systems in the vertical walls

2015

In this article the preliminary evaluation of the performance of a photovoltaic window is presented. The aim is to trace the behavior of next-generation systems, which favor architectonical integration. Three different systems have been taken into account: a dye sensitized solar cell (DSSC), blue and grey caved silicon panels. The systems can be placed behind a window or behind a wall of glass blocks.

Universal charts for optical difference frequency generation in the terahertz domain

2010

We present a universal and rigorous approach to study difference frequency generation in the terahertz domain, keeping the number of degrees of freedom to a minimum, through the definition of a suitable figure of merit. The proposed method relies on suitably normalized charts, that enable to predict the optical-to-terahertz conversion efficiency of any system based on wave propagation in quadratic nonlinear materials. The predictions of our approach are found to be in good agreement with the best experimental results reported to date, enabling also to estimate the d22 nonlinear coefficient of high quality GaSe.

Generazione di seconda armonica per quasi accordo di fase in guide a canale su LiNbO3 periodicamente polato in superficie.

2005

Opals infiltrated with a stimuli-responsive hydrogel for ethanol vapor sensing

2013

We report on a novel class of optical materials for ethanol vapor sensing, based on polystyrene opals infiltrated with an innovative stimuli responsive hydrogel. We describe the fabrication process of the bare polystyrene opals and their subsequent infiltration. The optical characterization of the photonic crystal templates was performed to prove the good quality of the samples. Measurements on the infiltrated opals showed that the transmission spectra in the visible range strongly change at varying concentrations of ethanol vapor. The fabricated structures show a linear optical response in the visible range, for high values of ethanol concentration.

Electrical characterization of high-efficiency bifacial silicon solar cells

2018

This work presents a preliminary study on the electrical characterization of high efficiency bifacial solar cells. An opening discussion on the state-of-the-art of such advanced technology is initially proposed and the experimental characterization of some prototypes is described. From this analysis, it can be stated that the bifacial silicon solar cells can be a very promising technology with high electrical performances and efficiency.

Characterization of PP-cLT Waveguides for phase conjugation in the C + L band of Optical Communications

2010

5th EOS Topical Meeting on Optical Microsystems, Poster OμS13_1569798553: Analytical Model for wideband THz sources and detectors based on Optical Re…

2013

Broadband Second-Harmonic Generation via Random Quasi-Phase-Matching in PPLT

2010

We demonstrated broadband second-harmonic generation via random Quasi-Phase-Matching in periodically poled Lithium Tantalate.

All-Optical frequency Shifter in a Periodically Poled Lithium Tantalate Waveguide

2011

A frequency shifting device is fabricated and tested in a congruent Lithium Tantalate waveguide. Periodic poling for quasi-phase-matching and channels for operation in the near-infrared C-band were obtained, demonstrating a two-stage parametric conversion.

A new Frequency Domain Measure of Causality based on Partial Spectral Decomposition of Autoregressive Processes and its Application to Cardiovascular…

2019

We present a new method to quantify in the frequency domain the strength of directed interactions between linear stochastic processes. This issue is traditionally addressed by the directed coherence (DC), a popular causality measure derived from the spectral representation of vector autoregressive (AR) processes. Here, to overcome intrinsic limitations of the DC when it needs to be objectively quantified within specific frequency bands, we propose an approach based on spectral decomposition, which allows to isolate oscillatory components related to the pole representation of the vector AR process in the Z-domain. Relating the causal and non-causal power content of these components we obtain…

Correlated Channel Model for terrestrial Free Space Optics and project specifications evaluation of LT code in OOK modulation

2011

Free Space Optics is a wireless line-of-sight communication system able to offer good bandwidth performance as well as straightforward installation and relocation. So that it represents a modern technology that allow to realize large bandwidth communication particularly when it is not possible to employ physical cable or radio technologies. Examples of FSO applications are: wireless backaul, fiber backup, temporary links, metro network extension and last mile access[1]. FSO is based on optical signals propagation in air and that is why it suffers of impairments which depend on atmospheric conditions. In detail, FSO suffers of scattering (i. e. Rayleigh and Mie) losses, absorption and scinti…

Brain Monitoring Via an Innovative CW-FNIRS System

2015

Functional Near InfraRed Spectroscopy (fNIRS) is an imaging technique mainly devoted to human brain monitoring. It is used as a non-invasive technique, in medical field, in order to measure the oxygen concentration of blood. This because the relatively good transparency of biological materials in the near infrared allows sufficient photon transmission through tissues. Within the so-called fNIRS range (650-900 nm), the main absorbers are blood chromophores, in particular the oxygenated and deoxygenated haemoglobin (HbO2 and Hb, respectively). When two or more wavelengths are used, changes of such chromophores can be computed by employing the modified Beer-Lambert law, thus providing importan…

Electrical characterization of highefficiency bifacial silicon solar cells

2018

This work presents a preliminary study on the electrical characterization of high efficiency bifacial solar cells. An opening discussion on the state-of-the-art of such advanced technology is initially proposed and the experimental characterization of some prototypes is described. From this analysis, it can be stated that the bifacial silicon solar cells can be a very promising technology with high electrical performances and efficiency.

Model Analysis of Hydrometeor Scattering Effects on Free Space Near-Infrared Links

2012

A promising technology for peer-to-peer connections and urban area networks is represented by wireless communications through free space using optical carrier (Free Space Optics, FSO). This technology ensures high data rates, with relatively low error rates, low power consumption and inherent security. Nevertheless FSO links are quite sensitive to atmospheric condition. Fog droplets, but also raindrops and snowflakes, may introduce severe path attenuation which drastically reduces the channel availability. A parametric model to simulate droplets scattering effects over the FSO link in terms of extinction coefficient, albedo factor and asymmetry coefficient as function of the particle water …

Parametrical study of multilayer structures for CIGS solar cells

2014

In this paper, a numerical analysis of relevant electrical parameters of multilayer structures for CIGS-based solar cells was carried out, employing the simulation software wxAMPS. In particular, we have focused on thin film cells having a ZnO:Al/ZnO/CdS/CIGS structure with a Molybdenum back contact. The aim of this work is to establish good theoretical reference values for an ongoing experimental activity, where our technology of choice is the single-step electrodeposition. In detail, we have analyzed how the main electrical properties change with the bang gap and the thickness of the absorber layer, for such a type of solar cell structure. Our results show that both efficiency and fill fa…

Continuous-Wave Backward Frequency Doubling in Periodically Poled Lithium Niobate

2010

We report on backward second-harmonic- generation in periodically poled lithium niobate with a 3.2 micron QPM period. A tunable continuous-wave Ti:Sapphire laser allowed us exciting two resonant orders. Experimental data compared well with standard theory.

Impact of GFETs geometries on RF performances

2016

Graphene is a relatively new material whose unique properties have attracted significant interest for its use in electronic and photonic applications. In particular, field effect has been proved in graphene samples and the observed high carrier mobility makes graphene an interesting solution for high frequency electronics. In this work, we focused on the analysis of microwave parameters dependence on geometries in Graphene Field Effect Transistors (GFETs). In particular, a statistical, experimental investigation of the cut-off frequency (fT) and of the output impedance (Zout) dependency on both the gate-drain/source distance (Δ) and the gate length (Lg) was carried out. 24 GFET families wer…

Responsivity measurements of N-on-P and P-on-N silicon photomultipliers in the continuous wave regime

2013

We report the electrical and optical comparison, in continuous wave regime, of two novel classes of silicon photomultipliers (SiPMs) fabricated in planar technology on silicon P-type and N-type substrate respectively. Responsivity measurements have been performed with an incident optical power from tenths of picowatts to hundreds of nanowatts and on a broad spectrum, ranging from ultraviolet to near infrared (340-820 nm). For both classes of investigated SiPMs, responsivity shows flat response versus the optical incident power, when a preset overvoltage and wavelength is applied . More in detail, this linear behavior extends up to about 10 nW for lower overvoltages, while a shrink is observ…

Graphene Field-Effect Transistors Employing Different Thin Oxide Films: A Comparative Study

2019

In this work, we report on a comparison among graphene field-effect transistors (GFETs) employing different dielectrics as gate layers to evaluate their microwave response. In particular, aluminum oxide (Al$_{2}$O$_{3}$), titanium oxide (TiO$_{2}$), and hafnium oxide (HfO$_{2}$) have been tested. GFETs have been fabricated on a single chip and a statistical analysis has been performed on a set of 24 devices for each type of oxide. Direct current and microwave measurements have been carried out on such GFETs and short circuit current gain and maximum available gain have been chosen as quality factors to evaluate their microwave performance. Our results show that all of the devices belonging …

Anomalous electrical parameters improvement in Ruthenium DSSC

2018

. In this work, we present a series of measurements carried out on Ruthenium-based Dye Sensitized Solar Cells (DSSCs) after the application of different external electrical field values. Such measurements have been performed both in the dark and by illuminating the sample with sunlight emitted by a solar simulator (AM1.5G spectrum with a power irradiance of 1000 W/m2). Our results demonstrate that the initial electrical bias field modifies in both cases the behavior of the cell in terms of an anomalous improvement of the main electrical parameters.

Experimental characterization of Ruthenium-based Dye Sensitized Solar Cells and study of light-soaking effect impact on performance

2016

In this paper, we present an experimental investigation on the performance of Ruthenium-based Dye Sensitized Solar Cells (DSSCs) at different irradiance levels, incident wavelengths and hours of illumination. In particular, the measurements have been aimed at studying the performance variation due to light soaking effect since this phenomenon has noteworthy practical implications, such as stability tests of DSSCs. Our results show that the short circuit current density, the open circuit voltage and the conversion efficiency η increase with the hours of light soaking. Finally, the observed phenomenon is reversible, and thus the performance decreases again when the cell is kept in the dark.

Hydrogel films engineered in a mesoscopically ordered structure and responsive to ethanol vapors

2014

Abstract Responsive hydrogels filling the interstitial spaces of photonic crystals can form mesoscopically structured materials, which exhibit reversible shifts in the Bragg diffracted light as a response of environmental changes. These materials can be used to generate chemical or biochemical sensors. The present work reports on the synthesis and characterization of ethanol responsive hydrogels that can be used in the design of novel breathalyzers. The dynamic mechanical behavior of the macroscopic hydrogels and their swelling features in the presence of different liquids or vapors have been investigated to orientate the choice of the best responsive material and curing process. The swelli…

Electro-Optical characterization of Silicon Carbide Schottky photodiodes

2014

Surface Periodic Domain Engineering in Congruent Lithium Tantalate Crystals

2006

First experiments with the novel electric field Surface Periodic Poling technique have been carried out on Lithium Tantalate. Optimal poling parameters gave 50:50 mark-to-space ratio in the micron scale with good uniformity and high repeatability.

Error mitigation using RaptorQ codes in an experimental indoor free space optical link under the influence of turbulence

2015

In free space optical (FSO) communications, several factors can strongly affect the link quality. Among them, one of the most important impairments that can degrade the FSO link quality and its reliability even under the clear sky conditions consists of optical turbulence. In this work, the authors investigate the generation of both weak and moderate turbulence regimes in an indoor environment to assess the FSO link quality. In particular, they show that, due to the presence of the turbulence, the link experiences both erasure errors and packet losses during transmission, and also compare the experimental statistical distribution of samples with the predicted Gamma Gamma model. Furthermore,…

Ultraviolet quasi-phase-matched second harmonic generation in surface periodically poled Lithium Niobate optical waveguides

2006

Nonlinear Disorder Mapping via Wave Mixing in poled Lithium Tantalate

2010

We introduce and test a simple approach for the characterization of domain distribution in bulk quadratic ferroelectric crystals, specifically periodically poled Lithium Tantalate with random mark-to space ratio.

Modelling of Quasi-TM0,0 Laser Operation in RPE:Nd3+:LiNbO3 Channel Waveguides.

2007

Fabrication of Graphene Field Effect Transistors (GFET) possessing a photoelectrical response

2014

Affordable, ultra-broadband coherent detection of terahertz pulses via CMOS-compatible solid-state devices

2017

We demonstrate the first fully solid-state technique for the coherent detection of ultra-broadband THz pulses (0.1-10 THz), relying on the electric-field-induced second-harmonic generation attained in integrated CMOS-compatible devices.

Characterization of thin film CIG(S,SE)2 submodules using solar simulator and laser beam induced current techniques (Versione estesa)

2015

In this work, the electrical and optical characterization of CIG(S, Se)2 sub-modules using both a solar simulator equipment and the Laser Beam Induced Current (LBIC) technique is presented. By using the solar simulator and a proper set-up, the electrical parameters of the modules at varying irradiance and temperatures are determined. In addition, the LBIC measurements are carried out to analyze the 2D photocurrent uniformity of the modules at two different wavelengths. Dispersion values of extracted parameters can be very useful for practically tuning the modelling stage at device/module level.

Observation of collapse arrest in pure kerr media sustained by a parametric interaction

2013

We demonstrate a parametric interaction based on four wave mixing that can arrest the collapse and stabilize solitary propagation in a pure Kerr material by controlling the wavelength of the interacting beams.

Continuous-wave backward frequency doubling in periodically poled lithium niobate

2010

We report on backward second-harmonic-generation in bulk periodically poled congruent lithium niobate with a 3.2 microns period. A tunable continuous-wave Ti:sapphire laser allowed us exciting two resonant quasi-phase-matching orders in the backward configuration. The resonances were also resolved by temperature tuning and interpolated with standard theory to extract relevant information on the sample.

A validity and reliability study of Conditional Entropy Measures of Pulse Rate Variability

2019

In this work, we present the feasibility to use a simpler methodological approach for the assessment of the short-term complexity of Heart Rate Variability (HRV). Specifically, we propose to exploit Pulse Rate Variability (PRV) recorded through photoplethysmography in place of HRV measured from the ECG, and to compute complexity via a linear Gaussian approximation in place of the standard model-free methods (e.g., nearest neighbor entropy estimates) usually applied to HRV. Linear PRV-based and model-free HRV-based complexity measures were compared via statistical tests, correlation analysis and Bland-Altman plots, demonstrating an overall good agreement. These results support the applicabil…

High resolution x-ray investigation of periodically poled lithium tantalate crystals with short periodicity

2009

Domain engineering technology in lithium tantalate is a well studied approach for nonlinear optical applications. However, for several cases of interest, the realization of short period structures (< 2 ��m) is required, which make their characterization difficult with standard techniques. In this work, we show that high resolution x-ray diffraction is a convenient approach for the characterization of such structures, allowing us to obtain in a nondestructive fashion information such as the average domain period, the domain wall inclination, and the overall structure quality.

AUTOFOCALIZZAZIONE VIA RANDOM QUASI-PHASE-MATCHING IN GUIDE D’ONDA DI TANTALATO di LITIO

2010

We observe self-localization of light beams via second harmonic generation in a quasi-phase-matched proton-exchanged Lithium Tantalate slab waveguide in the presence of a random component of the periodically-poled grating.

TOTAL INTERNAL REFLECTION ELLIPSOMETRY FOR THE SPECTROSCOPIC INVESTIGATION OF ULTRATHIN SILVER/OXIDE FILMS

2013

Investigation on Metal–Oxide Graphene Field-Effect Transistors With Clamped Geometries

2019

In this work, we report on the design, fabrication and characterization of Metal-Oxide Graphene Field-effect Transistors (MOGFETs) exploiting novel clamped gate geometries aimed at enhancing the device transconductance. The fabricated devices employ clamped metal contacts also for source and drain, as well as an optimized graphene meandered pattern for source contacting, in order to reduce parasitic resistance. Our experimental results demonstrate that MOGFETs with the proposed structure show improved high frequency performance, in terms of maximum available gain and transition frequency values, as a consequence of the higher equivalent transconductance obtained.

Measurements of Silicon Photomultipliers Responsivity

2012

We present some results on the optical characterization of Silicon Photomultipliers designed for medical imaging applications. In particular we will discuss our responsivity measurements performed with very low incident optical power and on a broad spectrum

Space-time features of THz emission from optical rectification in sub-wavelength areas

2011

We present our investigation on the THz space-time emission characteristic induced by the non-paraxial generation regime in highly localized THz generation via optical rectification on sub-wavelength areas.

Nanotechnology in lithium niobate for integrated optic frequency conversion in the UV

2017

In the domain of Earth Explorer satellites nanoengineered nonlinear crystals can optimize UV tunable solid-state laser converters. Lightweight sources can be based on Lithium Niobate (LN) domain engineering by electric field poling and guided wave interactions. In this Communication we report the preliminary experimental results and the very first demonstration of UltraViolet second-harmonic generation by first-order quasi-phase-matching in a surface-periodically-poled proton-exchanged LN waveguide. The pump source was a Ti-Sapphire laser with a tunability range of 700- 980 nm and a 40 GHz linewidth. We have measured UV continuous-wave light at 390 nm by means of a lock-in amplifier and of …

Photoelectrical response of Graphene Field Effect Transistors (GFETs)

2016

In this work, we present Graphene Field Effect Transistors (GFETs) with photoelectrical response due to the photovoltaiceffect. Our final aim is to use a GFET to down convert an optical to a radiofrequency signal. The technological steps used for the devices fabrication as well as the photoelectrical characterization will be reported. Photoelectrical measurements were performed by using a 405 nm laser diode source, whose output beam was pulse amplitude-modulated at 1.33 kHz by means of a laser driver. The electrical signal out of the GFETs (in a common source amplifier configuration) was measured using a lock-in amplifier synchronized to the same reference frequency of the laser driver. Thi…

Nanotecnologie in Niobato di Litio per la conversione di frequenza in ottica integrata nel campo UV.

2007

Terahertz Time-Domain Spectroscopy setup based on photoconductive antennas

2016

Despite the technical difficulties in developing efficient and compact sources and detectors for Terahertz (THz) radiation, this region of the electromagnetic spectrum is attracting an ever-increasing interest, due to its peculiar and high-potential applications in several fields, such as wideband communications, medicine, biology, non-destructive testing, security and defense. Within such contexts, the most widespread approach aiming to deal with THz pulses is based on the THz Time-Domain Spectroscopy (THz-TDS) system. In this work, we present our experimental results obtained by means of a THz-TDS set-up based on photoconductive antennas for both the generation and detection stage. It is …

Optical sensors for ethanol vapor based on polystyrene opals infiltrated with hydrogel

2013

This paper deals with a novel class of optical sensors for ethanol vapor, based on polystyrene opals infiltrated with a hydrogel sensitive to ethanol. Optical characterization of such opals has been performed, proving their effectiveness as sensors

Parametric conversion in micrometer and sub-micrometer structured ferroelectric crystals by surface poling

2012

We report on recent technological improvements concerning nonlinear patterning of lithium niobate and lithium tantalate in the micrometer and submicrometer scales using surface periodic poling for ferroelectric domain inversion. The fabricated samples were employed for frequency doubling via quasiphase-matching both in bulk and guided wave geometries, including forward and backward configurations and wavelength conversion in bands C and L. We also investigated short-period quasiperiodic samples with randomly distributed mark-to-space ratios.

Comparison of short-term heart rate variability indexes evaluated through electrocardiographic and continuous blood pressure monitoring

2019

Heart rate variability (HRV) analysis represents an important tool for the characterization of complex cardiovascular control. HRV indexes are usually calculated from electrocardiographic (ECG) recordings after measuring the time duration between consecutive R peaks, and this is considered the gold standard. An alternative method consists of assessing the pulse rate variability (PRV) from signals acquired through photoplethysmography, a technique also employed for the continuous noninvasive monitoring of blood pressure. In this work, we carry out a thorough analysis and comparison of short-term variability indexes computed from HRV time series obtained from the ECG and from PRV time series …

Guided-wave frequency doubling in surface periodically poled lithium niobate: competing effects

2007

We carried out second-harmonic generation in quasi-phase-matched ? -phase lithium niobate channel waveguides realized by proton exchange and surface periodic poling. Owing to a limited ferroelectric domain depth, we could observe the interplay between second-harmonic generation and self-phase modulation due to cascading and cubic effects, resulting in a nonlinear resonance shift. Data reduction allowed us to evaluate both the quadratic nonlinearity in the near infrared as well as the depth of the uninverted domains. © 2007 Optical

Asymmetric Dual-Grating Micro-Slit Configuration for Broadband Solid State Coherent Detection of THz Pulses

2016

We demonstrated solid-state broadband coherent Terahertz characterization based on the Terahertz Field Induced Second Harmonic effect in Silica. The THz detector consists of an asymmetric micro-slit array which can be operated at 200V applied bias.

Characterization of PP-cLT Waveguides for Second-Harmonic-Generation and Wavelength-Conversion in the C + L Band of Optical Communications

2010

We report the characterization of single-mode optical waveguides at telecom wavelength, realized in congruent lithium-tantalate. We demonstrate that waveguides realized by proton-exchange show a nonlinear coefficient matching that expected in a bulk crystal.

Measuring the Rate of Information Exchange in Point-Process Data With Application to Cardiovascular Variability

2022

The amount of information exchanged per unit of time between two dynamic processes is an important concept for the analysis of complex systems. Theoretical formulations and data-efficient estimators have been recently introduced for this quantity, known as the mutual information rate (MIR), allowing its continuous-time computation for event-based data sets measured as realizations of coupled point processes. This work presents the implementation of MIR for point process applications in Network Physiology and cardiovascular variability, which typically feature short and noisy experimental time series. We assess the bias of MIR estimated for uncoupled point processes in the frame of surrogate…

Rateless Codes Performance Analysis in Correlated Channel Model for GEO Free Space Optics Downlinks

2012

Optical dynamic monitoring in next generation networks, 10th International Conference on Telecommunications

2009

A portable electronic system for non-invasive real-time acquisition of multiple physiological signals

2019

In this work, we have designed and realised a portable and compact electronic system for the synchronous acquisition of multiple physiological signals. The system employs a Texas Instruments ADS1298 front-end with 24-bit resolution for data acquisition and supports up to 8 channels and 4 kHz sampling rate. The front-end communicates via SPI with a STM32 microcontroller which pre-processes the data and sends them through USB or Bluetooth to a suitable PC application. The system has been realized for the simultaneous acquisition of electrocardiographic (ECG) and photoplethysmographic (PPG) signals, but it can also be employed for acquiring other typologies of signals, e.g. breathing or electr…

Quasi Phase Matched UV Second Harmonic Generation in Lithium Tantalate soft PE Waveguides

2008

We report on first experimental results on UltraViolet second-harmonic generation by first-order quasiphase-matching in a surface periodically poled proton exchanged Lithium Tantalate waveguide. We have achieved a good compatibility with alpha phase proton exchanged channel waveguides in Lithium Tantalate. We held the sample in a temperature controlled oven kept at a constant temperature of 250 °C, to reduce photorefractive damage. The pump source was a Ti-Sapphire laser with a tunability range of 700 - 980 nm and a 40-GHz linewidth. Continuous wave UV light at 365.4 nm was produced with a conversion efficiency of 6.6% W-1cm-2.

Silicon Photomultipliers Signal-to-Noise Ratio in the Continuous Wave Regime

2014

 Abstract— We report on Signal-to-Noise Ratio measurements carried out, in the continuous wave regime, at different bias voltages, frequencies and temperatures, on a class of silicon photomultipliers fabricated in planar technology on silicon p- type substrate. Signal-to-Noise Ratio has been measured as the ratio of the photogenerated current, filtered and averaged by a lock-in amplifier, and the Root Mean Square deviation of the same current. The measured noise takes into account the shot noise, resulting from the photocurrent and the dark current. We have also performed a comparison between our SiPMs and a photomultiplier tube in terms of Signal-to-Noise Ratio, as a function of the tempe…

Silicon nitride-based deep sub-λ slit for ultra-broadband THz coherent detection

2018

We report on the characterization of a new type of CMOS-compatible device for terahertz solid-state biased coherent detection, which relies on a 1-µm-wide metallic slit embedded in a thin film of PECVD-grown silicon nitride.

Measurements of Silicon Photomultipliers Responsivity in Continuous Wave Regime

2013

We report on the electrical and optical characterization, in continuous wave regime, of a novel class of silicon photomultipliers fabricated in standard planar technology on a silicon p-type substrate. Responsivity measurements, performed with an incident optical power down to tenths of picowatts, at different reverse bias voltages and on a broad (340–820 nm) spectrum, will be shown and discussed. The device temperature was monitored, allowing us to give a physical interpretation of the measurements. The obtained results demonstrate that such novel silicon photomultipliers are suitable as sensitive power meters for low photon fluxes.

Space-time Features of THz Emitted from Optical Rectification Occurring in Sub-wavelength Scales

2011

Counter-propagating frequency mixing with Terahertz waves in diamond

2013

Frequency conversion by means of Kerr nonlinearity is one of the most common and exploited nonlinear optical processes in the UV, visible, IR, and mid-IR spectral regions. Here we show that wave mixing of an optical field and a terahertz wave can be achieved in diamond, resulting in the frequency conversion of the terahertz radiation either by sum- or difference-frequency generation. In the latter case, we show that this process is phase matched and most efficient in a counterpropagating geometry.

Feasibility of Ultra-Short-Term Analysis of Heart Rate and Systolic Arterial Pressure Variability at Rest and during Stress via Time-Domain and Entro…

2022

Heart Rate Variability (HRV) and Blood Pressure Variability (BPV) are widely employed tools for characterizing the complex behavior of cardiovascular dynamics. Usually, HRV and BPV analyses are carried out through short-term (ST) measurements, which exploit ~five-minute-long recordings. Recent research efforts are focused on reducing the time series length, assessing whether and to what extent Ultra-Short-Term (UST) analysis is capable of extracting information about cardiovascular variability from very short recordings. In this work, we compare ST and UST measures computed on electrocardiographic R-R intervals and systolic arterial pressure time series obtained at rest and during both post…

Rateless Codes Performance Tests On Terrestrial FSO Time-Correlated Channel Model

2012

Free Space Optics (FSO) links are affected by several impairments: optical turbulence, scattering, absorption, and pointing. In particular, atmospheric optical turbulence generates optical power fluctuations at the receiver that can degrade communications with fading events, especially, in high data rate links. A way to mitigate FSO link outages can be to add a coding to communications. Nevertheless, in order to study innovative solutions (software or hardware) and to improve the FSO link performance it needs accurate testing models. In this paper we describe an accurate time-correlated channel model able to predict random temporal fluctuations of optical signal irradiance caused by optical…

Fabbricazione di guide PE in LiTaO3 prive di instabilità

2008

Indoor free space optics link under the weak turbulence regime: Measurements and model validation

2015

In this study, the authors present the measurements performed on a free space optics (FSO) communications link using an indoor atmospheric chamber. In particular, the authors have generated several different optical turbulence conditions, demonstrating how even the weak turbulence regime can strongly affect the FSO link performance. The authors have carried out an in-depth analysis of the data collected during the measurements, and calculated the turbulence strength (i.e. scintillation index and Rytov variance) and the important performance metrics (i.e. the Q-factor and bit error rate) to evaluate the FSO link quality. Moreover, the authors have tested, for the first time, an appositely de…

Periodically nanostructured hydrogels for ethanol vapors sensing

2013

Chemical sensing using optics has been under extensive research all over the world during last decades and many optical chemical sensors are nowadays finding increasing applications in industry, environmental monitoring, medicine, biomedicine and chemical analysis. These optical sensors can be based on various optical principles, such as absorbance, reflectance or transmittance, luminescence and fluorescence, covering different regions of the spectrum (UV, visible, IR, NIR). Optical chemical sensors have several advantages over conventional electricity-based sensors, in terms of selectivity, immunity to electromagnetic interference, higher sensitivity, and they are also relatively inexpensi…

MAPPATURA DEL DISORDINE NON LINEARE MEDIANTE INTERAZIONE PARAMETRICA A TRE ONDE

2010

We introduce a simple approach for characterizing the ferroelectric domain distribution in bulk quadratic crystals. The approach is demonstrated in a lithium tantalate sample with periodic electric field poling and random mark-to-space ratio.

Information Dynamics of Electric Field Intensity before and during the COVID-19 Pandemic.

2022

This work investigates the temporal statistical structure of time series of electric field (EF) intensity recorded with the aim of exploring the dynamical patterns associated with periods with different human activity in urban areas. The analyzed time series were obtained from a sensor of the EMF RATEL monitoring system installed in the campus area of the University of Novi Sad, Serbia. The sensor performs wideband cumulative EF intensity monitoring of all active commercial EF sources, thus including those linked to human utilization of wireless communication systems. Monitoring was performed continuously during the years 2019 and 2020, allowing us to investigate the effects on the patterns…

Fading mitigation coding techniques for space to ground free space optical communications (Euro Med Telco 2014)

2014

In this manuscript, a Geostationary satellite-toground Free Space Optics (FSO) downlink channel model has been implemented, which is able to predict temporal irradiance fluctuations caused by scintillation at a wide range of turbulence conditions and for different values of the zenith angle. In order to mitigate fading events that occur in FSO communications, we have also tested the performance of three different families of Rateless Codes (Luby Transform, Raptor and RaptorQ) into our model and found that RaptorQ is the best candidate to mitigate errors in FSO links.

Electro-optic dynamics in thermally poled Ge core doped silica fibre

2003

The electro-optic (EO) dynamics of a twin hole germania core doped fibre when an applied electric field at elevated temperature modifies the symmetry of glass is reported. An EO peak was recorded after 10 min poling. The results were interpreted with a two-space charge model.

Simulation of parasitic effects on Silicon Carbide devices for automotive electric traction

2020

Wide Band Gap (WBG) semiconductors are increasingly addressed towards Electric Vehicle (EV) applications, due to their significant advantages in terms of high-voltage and low-losses performances, suitable for high power applications. Nevertheless, the packaging in WBG devices represents a challenge for designers due to the notable impact that inductive and capacitive parasitic components can bring in high switching frequency regime in terms of noise and power losses. In this paper, a comparison between conventional Silicon (Si) and emerging Silicon-Carbide (SiC) power switching devices is presented. The effects of inductive parasitic effects and switching frequency are investigated in simul…

Moderate-to-Strong Turbulence Generation in a Laboratory Indoor Free Space Optics Link and Error Mitigation via RaptorQ Codes

2016

Free Space Optics (FSO) is rapidly gaining interest as a line-of sight communication technology that offers capabilities similar - in terms of bandwidth and transfer rates - to optical fibre, also possessing several advantages compared with traditional radio frequency links. However, FSO link quality can be strongly affected by unfavourable weather conditions and also by the phenomenon of optical turbulence, even in clear sky. In this work, we have implemented an indoor FSO link and generated moderate-to-strong turbulence conditions along the optical path by using heaters and a mechanical ventilation system. In this way, we have been able to investigate the effects of the generated turbulen…

Electro-optical characterization of highly efficient Dye-Sensitized solar cells

2015

Nowadays, a growing demand for free and clean energy requires the study and the development of new low-cost solar photovoltaic (PV) cells. Among them, Dye Sensitized Solar Cells (DSSCs) based on ruthenium complexes as sensitizers are assuming a great importance. The DSSCs under study are composed placing in succession a transparent conductive glass on which is screen-printed a mesoporous TiO2 thin film sensitized by a ruthenium based dye (N719), an electrolytic solution containing a redox couple (I-/I3-) and another conductive glass covered by a thin transparent catalyst platinum film. In this work, we have measured the main photoelectrochemical parameters of the above mentioned DSSCs at di…

Respiratory Sinus Arrhythmia Mechanisms in Young Obese Subjects

2020

Autonomic nervous system (ANS) activity and imbalance between its sympathetic and parasympathetic components are important factors contributing to the initiation and progression of many cardiovascular disorders related to obesity. The results on respiratory sinus arrhythmia (RSA) magnitude changes as a parasympathetic index were not straightforward in previous studies on young obese subjects. Considering the potentially unbalanced ANS regulation with impaired parasympathetic control in obese patients, the aim of this study was to compare the relative contribution of baroreflex and non-baroreflex (central) mechanisms to the origin of RSA in obese vs. control subjects. To this end, we applied…

Role of nonlinear absorption during frequency doubling in lithium niobate waveguides.

2007

GENERAZIONE DI SECONDA ARMONICA RETRO-PROPAGANTE IN NIOBATO DI LITIO CON POLING PERIODICO

2010

We report on backward second-harmonic-generation in bulk periodically poled congruent lithium niobate with a 3.2 micron period. A tunable continuous-wave Ti:Sapphire laser allowed us exciting two resonant quasi-phase-matched orders. Resonances were also resolved by temperature tuning.

Optical characterization of polystyrene direct opals and of inverse-opal hydrogels

2012

Recovery Capabilities of Rateless Codes on Simulated Turbulent Terrestrial Free Space Optics Channel Model

2013

Free Space Optics (FSO) links are affected by several impairments: optical turbulence, scattering, absorption, and pointing. In particular, atmospheric optical turbulence generates optical power fluctuations at the receiver that can degrade communications with fading events, especially in high data rate links. Innovative solutions require an improvement of FSO link performances, together with testing models and appropriate channel codes. In this paper, we describe a high-resolution time-correlated channel model able to predict random temporal fluctuations of optical signal irradiance caused by optical turbulence. Concerning the same channel, we also report simulation results on the error mi…

Progettazione e realizzazione di biosensori a risonanza plasmonica superficiale in ottica integrata.

2007

Mutual Information Analysis of Brain-Body Interactions during different Levels of Mental stress

2019

In this work, we analyze brain-heart interactions during different mental states computing mutual information (MI) between the dynamic activity of different physiological systems. In 18 healthy subjects monitored in a relaxed resting state and during a mental arithmetic and a serious game task, multichannel EEG, one lead ECG, respiration and blood volume pulse were collected via wireless non-invasive biosensors. From these signals, synchronous 300-second time series were extracted measuring brain activity via the δ, θ, α, and β EEG power, and activity of the body district via the ECG R-R interval η, the respiratory amplitude ϱ and the pulse arrival time π. MI was computed using a linear est…

Cardiovascular parameters detection using a Photoplethismographic system

2016

We propose an innovative, cost-effective and easy to employ photoplethysmographic (PPG) system using Silicon Photomultipliers (SiPMs) sensors to measure cardiovascular parameters that can potentially represent markers for arterial stiffness

Spatio-temporal Characteristics of THz Emission at the Subwavelength Scale via Optical Rectification

2011

Highly localized THz emission via optical rectification in thin nonlinear crystals is a promising method for subwavelength microscopy. We present here the peculiar THz spatio-temporal characteristics induced by the non-paraxial generation regime.

Minimally Invasive Assessment of Mental Stress based on Wearable Wireless Physiological Sensors and Multivariate Biosignal Processing

2019

The development of connected health technologies for the continuous monitoring of the psychophysical state of individuals performing daily life activities requires the aggregation of non-intrusive sensors and the availability of methods and algorithms for extracting the relevant physiological information. The present study proposes an integrated approach for the objective assessment of mental stress which combines wirelessly connected low invasive biosensors with multivariate physiological time series analysis. In a group of 18 healthy subjects monitored in a relaxed resting state and during two experimental conditions inducing mental stress and sustained attention (respectively, mental ari…

Measurements of Silicon Photomultipliers Responsivity in Continuous Wave

2012

Proton exchange channel waveguides compatible with surface domain engineering in Lithium Niobate crystals

2006

First experiments of proton exchange channel waveguides compatible with electric field surface periodic poling of congruent lithium niobate crystals are addressed. Picosecond nonlinear copropagating QPM-SHG measurements have been carried out on such structures.

Generazione di luce UV per interazione QPM/SHG in guida ottica di niobato di litio congruente

2006

Surface periodic poling in congruent lithium tantalate

2006

The first demonstration of surface periodic poling of lithium tantalate at high voltages is reported. Periodic domain inversion with mark-to-space ratios close to the optimum 50:50 was successfully achieved down to micrometre periods with good uniformity and repeatability.

Ingegnerizzazione dei domini ferroelettrici nel niobato di litio per applicazioni nonlineari

2005

Nanotecnologie SPPLN con maschere in silica e fotoresist

2004

CIGS THIN FILM BY ONE-STEP ELECTRODEPOSITION FOR SOLAR CELLS

2013

In this work, we present a cost-effective technique to produce CIGS thin films for solar cells by means of a single-step electrodeposition. In fact, electrodeposition is known as an easy technique for building low cost materials for photovoltaic device processing. Morphological, structural and optical characterization of these films has been performed.

Variazione della pressione sistolica e diastolica con la respirazione

2016

L’attività di ricerca in corso riguarda la possibilità di ricavare dati clinicamente significativi dai segnali ottici PPG (PhotoPletysmoGraphy). Il segnale PPG viene utilizzato per ricavare informazioni sul volume e sulla saturazione del sangue che interessa il distretto illuminato dalla luce IR (infrarosso) usata per l’analisi. Il volume di sangue contenuto nel segmento di arteria esaminato dipende dalla pressione e dal ciclo cardiaco, attraverso la rigidità dell’arteria.

A prototypal PCB board for the EMI characterization of SiC-based innovative switching devices

2020

In this paper, a preliminary PCB board for the electromagnetic interference (EMI) characterization of innovative silicon-carbide (SiC) based switching devices is presented. Packaging technological issues can determine hurdles in the high-frequency switching and high power regime where wide band gap semiconductors are intended today for Electric Vehicle (EV) applications. In particular, the parasitic inductances that emerge in such devices, must be assessed, by using e.g. EMI techniques. In this specific case, the EMI characterization is supposed to be carried out in a semi-anechoic chamber, available at the University of Palermo (UNIPA), to assess the electromagnetic disturbances according …

Photoresponse of graphene ruthenium-complex heterostructures

2015

The aim of this study is to understand the photoresponse of a Ruthenium-complex/graphene heterostructure. Early work demonstrated that light detection by graphene field effect devices was enhanced by dropcasting Ruthenium Complex molecules. Here we proposed to fabricate a new class of devices where the Ruthenium-complex molecules are embedded between two layer of CVD monolayer graphene.

Implementation on NI-SOM sbRIO-9651 and Experimental Validation of Multi-Carrier PWM Techniques for Three-Phase Five Level Cascaded H-Bridge Inverter

2021

Multilevel Power Inverters (MPIs) represent a valid solution to improve the performances of energy production systems from renewable energy sources. Furthermore, the use of novel FPGA control systems allows simplifying the implementation of multicarrier PWM techniques for MPIs with computational benefits. This paper describes the implementation of several multicarrier PWM techniques on NI-SOM sbRIO-9651 for the control of a three-phase five-level cascaded H-bridge inverter. In detail, sbRIO-9651 is a control system in the field of Power Electronics and Drives (PED) programmable in the LabVIEW graphical programming environment. The paper is focused on modulation techniques implementation, te…

Comparison of frequency domain measures based on spectral decomposition for spontaneous baroreflex sensitivity assessment after Acute Myocardial Infa…

2021

Abstract The objective of this study is to present a new method to assess in the frequency domain the directed interactions between the spontaneous variability of systolic arterial pressure (SAP) and heart period (HP) from their linear model representation, and to apply it for studying the baroreflex control of arterial pressure in healthy physiological states and after acute myocardial infarction (AMI). The method is based on pole decomposition of the model transfer function and on the following evaluation of causal measures of coupling and gain from the poles associated to low frequency (0.04−0.15 Hz) oscillatory components. It is compared with traditional non-causal approaches for the sp…

Fading mitigation coding techniques for space to ground free space optical communications

2014

Exploiting the optical quadratic nonlinearity of zinc-blende semiconductors for guided-wave terahertz generation: A material comparison

2010

We present a detailed analysis and comparison of dielectric waveguides made of CdTe, GaP, GaAs and InP for modal phase matched optical difference frequency generation (DFG) in the terahertz domain. From the form of the DFG equations, we derived the definition of a very general figure of merit (FOM). In turn, this FOM enabled us to compare different configurations, by taking into account linear and nonlinear susceptibility dispersion, terahertz absorption, and a rigorous evaluation of the waveguide modes properties. The most efficient waveguides found with this procedure are predicted to approach the quantum efficiency limit with input optical power in the order of kWs.

Luby Transform Performance Tests on Time-Correlated Channel Model for Geo Free Space Optics Downlinks

2012

A wideband THz Time Domain Spectroscopy system based on pulsed laser: model and experiments

2014

Electrical characterization of low power CIGSSe photovoltaic modules

2015

This paper presents the electrical characterization of low power CIGSSe photovoltaic (PV) modules. Such investigation is achieved to perform a comparison of their performances with conventional silicon PV modules. For this purpose, a test bench, suitable for the characterization of both traditional and innovative low power modules, has been set-up and experimental results are accurately described and discussed.

Time, frequency and information domain analysis of short-term heart rate variability before and after focal and generalized seizures in epileptic chi…

2019

OBJECTIVE In this work we explore the potential of combining standard time and frequency domain indexes with novel information measures, to characterize pre- and post-ictal heart rate variability (HRV) in epileptic children, with the aim of differentiating focal and generalized epilepsy regarding the autonomic control mechanisms. APPROACH We analyze short-term HRV in 37 children suffering from generalized or focal epilepsy, monitored 10 s, 300 s, 600 s and 1800 s both before and after seizure episodes. Nine indexes are computed in time (mean, standard deviation of normal-to-normal intervals, root mean square of the successive differences (RMSSD)), frequency (low-to-high frequency power rati…

Electro-optical characterization of ruthenium-based dye sensitized solar cells: A study of light soaking, ageing and temperature effects

2017

Abstract In this work, we report on the electro-optical characterization of Dye Sensitized Solar Cells (DSSCs) which use ruthenium complexes as sensitizers. In particular, several kinds of measurements have been performed to study the electrical performances and the efficiency levels of the cells at different operating conditions. In detail, the measurements have been conducted at varying temperatures and hours of light soaking. Our results show that the short circuit current density J SC , the open circuit voltage V OC and the conversion efficiency η increase with the hours of light soaking, while they decrease with temperature. A thorough investigation on the light soaking process at the …

Characterization of Thin Film Cig(S,Se)2 Submodules Using Solar Simulator and Laser Beam Induced Current Techniques

2015

In this work, the electrical and optical characterization of CIG(S,Se)2 sub-modules using both a solar simulator equipment and the Laser Beam Induced Current (LBIC) technique is presented. By using the solar simulator and a proper set-up, the electrical parameters of the modules at varying irradiance and temperatures are determined. In addition, the LBIC measurements are carried out to analyze the 2D photocurrent uniformity of the modules at two different wavelengths. Dispersion values of extracted parameters can be very useful for practically tuning the modelling stage at device/module level.

Integrated frequency shifter in periodically poled lithium tantalate waveguide

2010

A frequency shifting device is fabricated and tested in a ferroelectric waveguide in a low-photorefractivity crystal. Periodic poling for quasi-phase-matching and channels for operation in the near-infrared C-band were obtained in congruent lithium tantalate, demonstrating for the first time both wave confinement and two-stage parametric conversion in such waveguides.

PV systems in the vertical walls: A comparison of innovative structures

2016

This paper presents the performance comparison of PV windows with the purpose of tracing the behavior of next-generation systems, which could favor architectonical integration. More in detail, a dye sensitized solar cell (DSSC) and blue and grey thin film silicon panels have been analyzed. The systems can be placed behind a window or behind a wall of glass blocks. The three generation systems are then compared in terms of both efficiency and Fill Factor.

Novel Configuration for a C-Band Axial Vircator With High Output Power

2022

We present a novel configuration for an axial virtual cathode oscillator (Vircator) operating in the C-band and designed for high output power applications. In order to enhance the efficiency, we have employed a geometry with up to seven reflectors along the drift space. While in previous research works this optimization process has been performed only varying the reflectors radii while using a fixed distance between reflectors,in our work we propose an optimization in terms of both reflectors radii and distances. Our optimized structure for the axial Vircator is able to provide an efficiency up to 15.6% and an output power of 1.6 GW in the C-band, with a working voltage of 510 kV and a cat…

Thin Film CIGS Solar Cells, Photovoltaic Modules, and the Problems of Modeling

2013

Starting from the results regarding a nonvacuum technique to fabricate CIGS thin films for solar cells by means of single-step electrodeposition, we focus on the methodological problems of modeling at cell structure and photovoltaic module levels. As a matter of fact, electrodeposition is known as a practical alternative to costly vacuum-based technologies for semiconductor processing in the photovoltaic device sector, but it can lead to quite different structural and electrical properties. For this reason, a greater effort is required to ensure that the perspectives of the electrical engineer and the material scientist are given an opportunity for a closer comparison and a common language.…

Adaptive scheduling of acceleration and gyroscope for motion artifact cancelation in photoplethysmography

2022

Background and objective: Recently, various algorithms have been introduced using wrist-worn photo-plethysmography (PPG) to provide high accuracy of instantaneous heart rate (HR) estimation, including during high-intensity exercise. Most studies focus on using acceleration and/or gyroscope signals for the motion artifact (MA) reference, which attenuates or cancels out noise from the MA-corrupted PPG signals. We aim to open and pave the path to find an appropriate MA reference selection for MA cancelation in PPG.Methods: We investigated how the acceleration and gyroscope reference signals correlate with the MAs of the distorted PPG signals and derived both mathematically and experimentally a…

Electrochemical Conversion of Dichloroacetic Acid to Chloroacetic Acid in Conventional Cell and in Two Microfluidic Reactors

2013

The electrochemical conversion of dichloroacetic acid to chloracetic acid is investigated in conventional cells and in microreactors. Two different microreactors are used: the first is a filter press cell equipped with PTFE micrometric spacers, easy to assemble and disassemble and available for a large variety of electrodes and solvents; the second is made using an adhesive spacer, micromilling and press and could easily be developed on an industrial scale. The electrochemical synthesis is performed successfully in the microreactors equipped with a graphite cathode under proper operative conditions. The performance of the process strongly depends on the nature of the cathode and, for micror…

SPATIOTEMPORAL FEATURES OF THZ GENERATED VIA OPTICAL RECTIFICATION IN SUB-WAVELENGTH TRANSVERSE DIMENSION

2011

Second Harmonic Generation via Random Quasi-phase Matching in a Periodically Poled Lithium Tantalate Waveguide

2011

We observe second harmonic generation via random quasi phase matching in a 1.5μm periodically poled lithium tantalate. The presence of a slab waveguide allows the comparison between bulk and guided wave configurations.

TOF LiDAR with SiPM technology

2016

LiDAR (Light Detection And Ranging) systems measures the distance from the sensor to the target by determining the time between the release of the laser pulse to the receiving of the backscattered pulse. The interest in LiDAR technology has exploded in recent years since the applications are numerous. Here, we would highlight the Advanced Driver Assistance Systems (ADAS) and for rendezvous & docking operations between spacecraft. We built two LiDAR systems differing for the detector: a Silicon Photomultiplier (SiPM) and an Avalanche Photodiode (APD). The advantages of the SiPM approach has been extensively discussed in [1]. The comparison between these systems has been performed in terms of…

Prima dimostrazione di generazione UV per QPM in guide ottiche PE il LiTaO3

2008

Light Soaking measurements on Ruthenium-based Dye Sensitized Solar Cells

2016

An interesting phenomenon occurring in Dye Sensitized Solar Cells (DSSCs) when exposed to an uninterrupted period of illumination is the so-called light soaking effect, which consists in the increase of the main electrical parameters of the cell, such as the photocurrent and the efficiency. Studying such an effect has noteworthy practical implications, ranging from the optimization of the manufacturing process to stability tests of DSSCs. In this paper, we present an experimental investigation on the performance variation, due to light soaking, of Ruthenium-based DSSCs.

Spatial and spectral properties of small area THz generation for sub-wavelength microscopy

2010

A highly localized THz source is a promising candidate for sub-wavelength microscopy, due to its superior radiation power throughput with respect to others near-field techniques. Here, we report on the spatial and the spectral near-field properties of our highly localized THz source.

Continuous Wave fNIRS with Silicon Photomultiplier

2015

This work is focused on the development of a Continuous Wave (CW) NIRS integrated system with multi-wavelength LED sources between 700 and 950 nm and a Silicon Photomultiplier detector (SiPM) developed by STMicroelectronics. The Signal Noise Rate (SNR), measured placing the LEDs and an SiPM in a direct contact with the surface of a plastic phantom mimicking a real human head, results higher than the calculated minimum, required to detect small variation in the HbO2 and HHb concentration, till a source detector separation (SDS) of 6 cm.

Signal to Noise Ratio of Silicon Photomultipliers: a study in the Continuous Wave Regime

2014

We report on Signal to Noise Ratio measurements carried out, in the continuous wave regime, at different bias voltages, frequencies and temperatures, on a novel class of silicon photomultipliers fabricated in planar technology on silicon p-type substrate. Signal to Noise Ratio has been measured as the ratio of the photogenerated current, filtered and averaged by a lock-in amplifier, and the Root Mean Square deviation of the same current. The measured noise takes into account the shot noise, resulting from the photocurrent and the dark current. We have also performed a comparison between our SiPMs and a photomultiplier tube in terms of Signal to Noise Ratio, as a function of the temperature …

CIGS Thin Film by One-Step Electrodeposition Deposition for Solar Cells

2013

Frequency doubling in surface periodically-poled lithium niobate waveguides: role of cascading and nonlinear absorption

2008

Nanotecnologie SPPLN per Dispositivi a Cristalli Fotonici

2004

Counter-propagating difference-frequency generation in diamond with terahertz fields

2013

The nonlinear interaction of terahertz (THz) pulses with optical fields in Kerr, gaseous media is a key ingredient for broadband THz detection schemes [1]. Terahertz field-induced second harmonic generation in solid-state media has also been considered for THz detection and as a tool e.g. for liquid dynamics investigations [2,3], while four-wave mixing has been addressed as a possible mechanism for THz generation [4,5]. © 2013 IEEE.

Photovoltaic module characteristics from CIGS solar cell modelling

2013

We describe our approach to the task of modelling, both at single cell structure and complete module levels, during the solar cell technology development process. This can give very helpful indications, in terms of global photovoltaic module characteristics, for the assessment of intermediate research results and planning of further experiments. We make reference specifically to the fabrication of thin film CIGS solar cells by means of single-step electrodeposition, a technique which appears fairly easy and low-cost but, at the same time, can lead to quite different structural and electrical properties.

SNR measurements of silicon photomultipliers in the continuous wave regime

2014

We report on our Signal-to-Noise Ratio (SNR) measurements carried out, in the continuous wave regime, at different frequencies and at various temperatures, on a novel class of silicon photomultipliers (SiPMs) fabricated in planar technology on silicon p-type substrate. SNR of SiPMs is given by the ratio of the photogenerated current, filtered and averaged by a lock-in amplifier, and the Root Mean Square (RMS) deviation of the same current. In our measurements, we have employed a 10 Hz equivalent noise bandwidth, around the lock-in amplifier reference frequency. The measured noise takes into account the shot noise, resulting from the photocurrent and the dark current, while background light …

Interference-Based Chromatic Coatings by Ion Plating Plasma Assisted Deposition Technology

2010

The goal of replacing widespread and inexpensive galvanic treatments with suitable vacuum deposition techniques, in order to eliminate the environmental hazards and their polluting effects, is becoming, in some cases, more tangible. Shorter cleaning cycles, shorter pump-down times, reduced heating times of substrates and higher deposition rates allow the costs of new plasma-assisted processes to become competitive with respect to galvanic ones. Moreover, vacuum treatments offer superior mechanical and optical properties and non-conductive substrates (like glass, ceramics, plastics) can be more easily coated. This work describes the results obtained with Ion Plating Plasma Assisted depositio…

Imaginary distance BPM as an efficient tool for modelling optical waveguide fabrication by ion diffusion

2006

Photocurrent generation in Graphene Field Effect Transistors (GFETs)

2016

In this work, we focused on the study of Graphene Field Effect Transistors (GFETs) photoelectrical response due to the combination of photovoltaic and photo-thermoelectric effects. The technological steps for the transistors fabrication together with their electro-optic response will be presented. Measurements were performed by using a 405 nm laser diode with AM modulation at 1.33 KHz shined onto the sample under test. GFETs electrical output signals were measured by using a lock-in amplifier synchronized to the same reference frequency of the laser driver. This gave us the possibility to evaluate the optical characteristics as a function of both the incident laser power and the static pola…

Nonlinear Disorder Mapping via Three Wave Mixing in Poled Lithium Tantalate

2010

We introduce and test a simple approach for the characterization of domain distribution in bulk quadratic ferroelectric crystals, such as periodically poled Lithium Tantalate with random mark-to space ratio.

Vascular resistance arm of the baroreflex: methodology and comparison with the cardiac chronotropic arm.

2020

Baroreflex response consists of cardiac chronotropic (effect on heart rate), cardiac inotropic (on contractility), venous (on venous return) and vascular (on vascular resistance) arms. Because of its measurement simplicity, cardiac chronotropic arm is most often analysed. The aim was to introduce a method to assess vascular baroreflex arm, and to characterize its changes during stress. We evaluated the effect of orthostasis and mental arithmetics (MA) in 39 (22 female, median age: 18.7 yrs.) and 36 (21 female, 19.2 yrs.) healthy volunteers, respectively. We recorded systolic and mean blood pressure (SBP and MBP) by volume-clamp method and R-R interval (RR) by ECG. Cardiac output (CO) was re…

Poling periodico superficiale in tantalato di litio congruente

2006

PARAMETRIC SELF-TRAPPING OF OPTICAL BEAMS VIA RANDOM QUASI PHASE MATCHING IN LITHIUM TANTALATE WAVEGUIDE

2011

We report on experimental evidence of parametric spatial solitons in a lithium tantalate waveguide with randomized periodic ferroelectric poling. Two-color self-focusing via quadratic cascading overcomes the diffractive nature of both fundamental and frequency-doubled beams.

Features of randomized electric-field assisted domain inversion in lithium tantalate

2011

We report on bulk and guided-wave second-harmonic generation via random Quasi-Phase-Matching in Lithium Tantalate. By acquiring the far-field profiles at several wavelengths, we extract statistical information on the distribution of the quadratic nonlinearity as well as its average period, both at the surface and in the bulk of the sample. By investigating the distribution in the two regions we demonstrate a non-invasive approach to the study of poling dynamics.

CuInSe2/Zn(S,O,OH) junction by electrochemical and chemical route for photovoltaic applications (GE 2014)

2014

Electrodeposition is a convenient technique for the development of low cost materials for photovoltaic (PV) device processing. Using a single step electrodeposition route, several groups have fabricated CIS (CuInSe) and CIGS (CuInGaSe) films. One of the most important requirements for successful application of one-step electrodeposition film formation is the ability to control composition of the deposited films and to develop polycrystalline microstructures with a low surface roughness and high sintered density.

Nonlinear Disorder Mapping Via Three-Wave Mixing in Quadratic Crystals

2010

Optical turbulence measurements and channel modeling of an indoor Free Space Optics link

2014

Photonic crystal hydrogel films responsive to ethanol vapors

2013

Employing Microwave Graphene Field Effect Transistors for Infrared Radiation Detection

2018

In this work, we investigate the possibility of employing graphene field effect transistors, specifically designed for microwave applications, as infrared detectors for telecom applications. Our devices have been fabricated on a sapphire substrate employing CVD-grown transferred graphene. The roles of both the gate dielectric and the DC bias conditions have been evaluated in order to maximize the infrared generated signal through an experimental investigation of the signal-to-noise ratio dependence on the transistor operating point.

Ostruzione polmonare ed aritmia respiratoria

2019

Il monitoraggio di pazienti tramite segnali fotopletismografici (PhotoPlethysmoGram, PPG) acquisiti sul polso, arteria radiale, piuttosto che sulla punta dell’indice, permette di ottenere un segnale più stabile e con maggiori informazioni, come la gittata cardiaca, la durata della contrazione ventricolare e la chiusura dell’aorta. In questo lavoro è presentata un’attività preliminare per rilevare condizioni come l’ostruzione polmonare e le apnee notturne. Si è indagato l’andamento dell’aritmia respiratoria in relazione ad eventuali difficoltà respiratorie. Per il momento ci si è limitati ad osservare soggetti sani e l’ostruzione è stata simulata facendo respirare i soggetti attraverso una c…

Prima sorgente nell’UV in ottica integrata ottenuta per QPM-SHG in Tantalato di Litio

2008

Development of a CW-fNIRS System for brain monitoring

2014

A portable system for multiple parameters monitoring: towards assessment of health conditions and stress level in the automotive field

2019

In this work, an electronic portable combo system able to synchronously acquire multiple signals, e.g. electrocardiographic (ECG), photoplethysmographic (PPG) and breathing waveforms, is presented. The realized system is also capable of showing in real time some physiological parameters which can be used for assessing health/stress status of the volunteer, such as heart rate and breathing frequency and their trends over time. Thanks to the use of non-invasive PPG probes, of batteries as power supply, and to the possibility to add in the future additional sensors to acquire other signals, the system could also be employed inside vehicles for assessing the status of the driver. Finally, the r…

Physiological parameters measurements in a cardiac cycle via a combo PPG-ECG system

2015

In this paper, we present an innovative way to measure some physiological parameters (such as the pre-ejection period, the pulse transit time, the blood pressure) in a cardiac cycle. A combo PPG-ECG system has been developed and employed to extract both the ECG signal from standard limb leads and simultaneously the photoplethysmography signal from the wrist and the forearm, to calculate the pre-ejection period. This system represents an easy and non-invasive technique to determine these biomedical parameters without using expensive impedance cardiography equipment.

Guide d’onda a scambio protonico in cristalli ferroelettrici con domini ingegnerizzati superficialmente

2006

Blood Pressure Monitoring with a PPG Embedded System

2014

Backward Frequency Doubling in Periodically Poled Lithium Niobate in the Pulsed Regime

2011

Frequency doubling in surface periodically poled lithium niobate waveguides: Competing effects

2007

We fabricated α-phase pro ton-exchanged (PE) lithium niobate (LN) channel waveguides quasi phase-matched (QPM) via surface periodic poling (SPP) and carried out the first experimental demonstration of second harmonic generation (SHG) in such devices.[1] Experiments were performed by employing an optical parametric amplifier/oscillator producing 25 ps pulses in the range 1.1-1.6 μm with a line-width less than 2cm−1 and a repetition rate of 10Hz. SHG measurements were performed either at a fixed wavelength by varying the fundamental frequency (FF) input power or by scanning the FF wavelength, ratioing the second harmonic (SH) output to the FF input to obtain the conversion efficiency. By repe…

Fabrication and characterization of graphene field effect transistors (GFET)

2015

Graphene is a flat monolayer of carbon atoms tightly packed into a two-dimensional (2D) honeycomb lattice. This peculiarity is responsible of extraordinary physical properties. Graphene exhibits a strong ambipolar field effect and thanks to its huge charge carrier mobility, graphene is a suitable material for high frequency Electronics. Graphene field effect transistors (GFET) for high frequency applications have recently received much attention and significant progress has been achieved in this area. GFETs have been already made by using pre-patterned metal or graphene nanoribbon (GNR) back-gates and hexagonal boron nitride as a dielectric spacer. Among the most employed techniques for the…

P-on-N and N-on-P silicon photomultipliers: an in-depth analysis in the continuous wave regime

2013

We report on the electrical and optical comparison, in the continuous wave regime, of two novel classes of silicon photomultipliers fabricated in planar technology on silicon P-type (N-on-P class) and N-type (P-on-N class) substrates respectively.

Numerical Model of THz sources and detectors based on Optical Rectification and Electro-Optic Sampling

2013

A model describing a laser based set-up for wideband THz generation and detection is presented. Particular attention is focused on the main broadband phenomena, which occur when THz radiations have to be handled.

ELECTROCHEMICAL TREATMENT OF WASTE WATERS CONTAMINATED BY ORGANIC POLLUTANTS: A LOOK ON SOME NEW APPROACHES

2012

Recent researches have demonstrated that electrochemical methods offer an attractive alternative to traditional routes for treating wastewaters containing toxic or/and refractory organic pollutants. These methods use a clean reagent, as the electron, very mild operative conditions (ambient temperature and pressure) and can be run with limited operative costs. Despite of the above mentioned advantages, electrochemical processes present some important disadvantages such as: • the cost of some electrodic materials such as silver (for reduction processes) and boron doped diamond (for oxidation ones). On the other hand, the cost of silver based electrodic materials can be considerably lowered by…

Feasibility of Ultra-short Term Complexity Analysis of Heart Rate Variability in Resting State and During Orthostatic Stress

2022

In this work, we study ultra-short term (UST) complexity of Heart Rate Variability (HRV) and its agreement with analysis of standard short-term (ST) HRV recordings obtained at rest and during orthostatic stress. Conditional Entropy (CE) measures have been computed using both a linear Gaussian approximation and a more accurate model-free approach based on nearest neighbors. The agreement between UST and ST indices has been compared via statistical tests and correlation analysis, suggesting the feasibility of exploiting faster algorithms and shorter time series for detecting changes in cardiovascular control during various states.

Optical turbulence measurements and channel modeling of an indoor Free Space Optics link (Versione estesa)

2014

In this work, we propose an indoor experimental set-up able to generate several optical turbulence conditions in a Free Space Optics link. Using this set-up, we prove the effectiveness of an irradiance time-series generator based on the Gamma-Gamma model and able to predict the irradiance fluctuations at the receiver, under both weak and moderate turbulence conditions.

Model-Based Transfer Entropy Analysis of Brain-Body Interactions with Penalized regression techniques

2020

The human body can be seen as a functional network depicting the dynamical interactions between different organ systems. This exchange of information is often evaluated with information-theoretic approaches which comprise the use of vector autoregressive (VAR) and state space (SS) models, normally identified with the Ordinary Least Squares (OLS). However, the number of time series to be included in the model is strictly related to the length of data recorded thus limiting the use of the classical approach. In this work, a new method based on penalized regressions, the so-called LASSO, was compared with OLS on physiological time-series extracted from 18 subjects during different stress condi…

Fading mitigation coding techniques for space to ground free space optical communications

2014

In this manuscript, a Geostationary satellite-toground Free Space Optics (FSO) downlink channel model has been implemented, which is able to predict temporal irradiance fluctuations caused by scintillation at a wide range of turbulence conditions and for different values of the zenith angle. In order to mitigate fading events that occur in FSO communications, we have also tested the performance of three different families of Rateless Codes (Luby Transform, Raptor and RaptorQ) into our model and found that RaptorQ is the best candidate to mitigate errors in FSO links. Keywords— Optical Wireless Communications; Space-toGround FSO links, time-series, rateless codes; fading mitigation

Wearable Multisensor Ring-Shaped Probe for Assessing Stress and Blood Oxygenation: Design and Preliminary Measurements

2023

The increasing interest in innovative solutions for health and physiological monitoring has recently fostered the development of smaller biomedical devices. These devices are capable of recording an increasingly large number of biosignals simultaneously, while maximizing the user’s comfort. In this study, we have designed and realized a novel wearable multisensor ring-shaped probe that enables synchronous, real-time acquisition of photoplethysmographic (PPG) and galvanic skin response (GSR) signals. The device integrates both the PPG and GSR sensors onto a single probe that can be easily placed on the finger, thereby minimizing the device footprint and overall size. The system enables the e…

A LiDAR Prototype with Silicon Photomultiplier and MEMS Mirrors

2018

In this paper, we present a low cost prototype of a Time-Of-Flight (TOF) LiDAR system, employing a SiPM as photo detector and MEMS mirrors in order to steer the nanosecond pulsed optical beam with a scanning angle of +/-6°. Preliminary TOF measurements have been performed both indoor and outdoor to test the limits of the system.

Microwave parameters dependence on Graphene Field Effect Transistors (GFETs) dimensions

2016

Graphene is a relatively new material whose unique properties have attracted significant interest for its use in electronic and photonic applications. In particular, field effect has been proved in graphene samples and this feature, together with the high carrier mobility observed, makes graphene an interesting solution for high frequency electronics. In our work, we performed a statistical analysis in order to evaluate the microwave parameters dependence on Graphene Field Effect Transistors (GFETs) dimensions. In more detail, for the first time, we studied the behavior of the cut-off frequency (ft) and of the output impedance (Zout) at varying both the gate-drain/gate-source distance (Δ) a…

Wideband THz time domain spectroscopy set-up based on ultrafast pulsed laser: model and experiments

2014

We present an analytical model describing the full electromagnetic propagation in a THz Time Domain Spectroscopy (THz-TDS) laser based system. We pay particular attention to the modelling of the time-frequency behavior of all the stages, which compose our experimental set-up. In particular, our model takes into account the following features: pump beam focusing into the generation crystal; phase-matching between pump and THz pulses inside both the generation and detection crystals; chromatic dispersion and absorption inside the materials; Fabry-Perot effect in both the crystals; diffraction along the propagation, focalization and overlapping between THz and probe beams; Electro-Optic Sampli…

Modelling of wideband THz sources and detectors based on Optical Rectification and Electro-Optic Sampling

2012

Nonstoichiometric silica mask to fabricate reverse proton-exchange waveguides in lithium niobate crystals

2004

Producing channel waveguides requires a photolithographic mask, but the standard technique of using thermally evaporated metal films for proton exchange has proved to be unsuitable for withstanding the rather aggressive process of reverse proton exchange. We report the fabrication of a nonstoichiometric silica mask by ion-plating plasma-assisted deposition. This mask is strong enough to resist both direct and reverse proton exchange and is also compatible with anisotropic dry etching for patterning the mask and with electric field poling. Our technique is a practical alternative to the use of SiO2 sputtered masks.

Comparison in terms of TOF measurements between APD and SiPM for LiDAR applications

2016

We present an experimental comparison of two LiDAR systems, employing the SiPM and the APD as photodetectors, in terms of TOF measurements differing for the distance of the target and at different intensities of ambient light. The use of the APD represents the conventional approach, while the implementation of the SiPM is innovative. The performed measurements achieved very promising results, thus demonstrating the effectiveness of our LiDAR based on SiPM.

Comparison between SiC and GaN switching devices in fast-recharging systems for electric vehicles

2023

Recently, the improvement of the semiconductor devices to achieve higher efficiency and higher power density has risen to interest. Si carbide and gallium nitride offer faster switching frequency and lower losses; however, the knowledge of the behaviour of these devices is not mature. In this paper, a system for fast charging of batteries for electric vehicles based on an isolated DC-DC converter equipped with both SiC and GaN devices is presented and an interesting experimental comparison among these two technologies will be given in terms of dynamic performances, electromagnetic compatibility, stability, efficiency, and so on.

Infrared detection in multifunctional graphene-based transistors

2016

In the last years great attention has been paid to graphene-based devices for optoelectronic applications such as photodetection. In this work, we report on Graphene Field Effect Transistors (GFETs) photoelectrical response due to the photo-transistor effect. Photoelectrical measurements were performed using a 1.55 μm erbium fiber laser. Optical measurements as a function of both the incident laser power and the DC bias of the fabricated devices have been carried out and show that photocurrent increases with the power of the IR beam illuminating the sample.